MSI GE40 User manual

GE40/CR42 (MS-1492) Disassemble Guide
■1、BATTERYPACK
■2、HDD&ODD MODULE/BOTTOMDOOR
■3、THERMAL-KIT、DRAMMODULE
■4、CPU&WLANMODULE
■5、SEPARATEUPPERCASEAND LOWERCASE
■6、LOWERCASEASSY
■7、LCDMODULE ASSY

GE40/CR42 (MS-1492) Disassemble Guide
■1、BATTERYPACK
1.1：Move the “Unlock’ button base on left picture
shows;
1.2:Push the “Release” button and move the battery
pack base on left picture.
Component
P/N
Qty
Battery Pack
S9N-4362210-M47
1

GE40/CR42 (MS-1492) Disassemble Guide
■2、HDD&ODD MODULE/BOTTOMDOOR
2.1：Remove the 2 screws (M2.5*5mm), then Remove
the 2 screws (M2.5*6mm),last Remove the 2 screws
(M3*3.5mm)，remove the Bottom door.
Attention: the screw driver touque is: 1.7-2.0Kgf-cm
Component
P/N
Qty
Bottom door
307-491J213-Y31
1
Screw
E43-1303013-G68
2
Screw
E43-1256001-H29
2
Screw
E43-1255001-H29
2
2.2：Remove the 1 screws (M2.5*5mm);then remove
ODD Module.
Attention: the screw driver touque is: 1.7-2.0Kgf-cm
Component
P/N
Qty
ODD MODULE
S7D-2170016-T87
1
screw
E43-1255001-H29
1
2.3 ：Remove the HDD Module according to the
direction as pic shows.
Component
P/N
Qt
HDD MODULE
S71-2475702-W36
1
2.5*5mm
2.5*6mm
3*3.5mm

GE40/CR42 (MS-1492) Disassemble Guide
■3、THERMAL-KIT、DRAMMODULE
3.1:Push the two side shielding of DRAM as pic
shows;.
Component
P/N
Qty
DRAM Module
S7C-S56AD01-K37
2
3.2:Remove the 2 screws(M2.5*5mm) and FAN
cable, after that remove the Fan.
Attention：the screw driver torque is 1.5-2.0Kgf-cm
Component
P/N
Qty
Fan
E33-0800261-MC2
1
Screw
E43-1255001-H29
2
3.3：Remove the 3 screws (M2.5*5mm) ，after that
remove the heatsink.
Attention：the screw driver torque is 1.2-2.0Kgf-cm
Component
P/
Qty
Screw
E43-1255001-H29
3
HEATSINK
E31-0804090-CA9
1

GE40/CR42 (MS-1492) Disassemble Guide
■4、CPU&WLAN MODULE
4.1:Open the CPU Slot with hexagonal screwdriver
, then remove CPU Module as below.
Component
P/N
Qty
CPU
A13-22201G6-I06
1
4.2：Remove 1 screw(M2*3mm); then remove the
two sides wireless card antenna as pic shows:
Attention: the screw driver torque is: 1.8-2.0Kgf-cm
Component
P/N
Qty
Wreless card
S57-08000J0-T46
1
Screw
E43-1203003-H29
1

GE40/CR42 (MS-1492) Disassemble Guide
■5、SEPARATE UPPER CASE AND LOWER CASE
■
5.1：Remove the Keyboard as pic shows.
Componen
P/N
Qty
Keyboard
S1N-2EUS291-SA0
1
5.2：Disconnect Keyboard Cable as pic shows.

GE40/CR42 (MS-1492) Disassemble Guide
■5、SEPARATE UPPER CASE AND LOWER CASE
■
5.3：Remove the 8 screws(M2.5*5mm);
Attention: the screw driver torque is: 2.0-2.5Kgf-cm
Component
P/N
Qty
Screw
E43-1255001-H29
8
5.4：Remove lower case，then remove DC IN
Module;
Component
P/N
Qty
DC IN
K10-3006142-V03
1
5.5：Remove the LVDS cable as pic shows:
Component
P/N
Qty
LVDS Cable
K19-3040045-H39
1

GE40/CR42 (MS-1492) Disassemble Guide
■6、LOWER CASE ASSY
6.1：Remove the MIC cable as pic shows:
6.2：Remove the Audio Board,Then Remove the
Audio cable as pic shows.
Component
P/N
Qty
Audio Board
607-1492A-02S
1
6.3：Draw Out Antenna and MIC Cable as pis
shows.
Audio

GE40/CR42 (MS-1492) Disassemble Guide
■6、LOWER CASE ASSY
■
6.4：Remove the 1 screws (M2.5*5mm)and Remove
the 1 screws (M2*3.5mm)that stabilize the left LCD
hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component
P/N
Qty
Screw
E43-1255001-H29
1
Screw
E43-1203501-H29
1
6.5：Remove the 1 screws (M2.5*5mm)and Remove
the 1 screws (M2*3.5mm)that stabilize the Right LCD
hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component
P/N
Qty
screw
E43-1255001-H29
1
screw
E43-1203501-H29
1
6.6:Disconnect Touchpad Cable as pic shows,then
remove MB.
Component
P/N
Qty
MB
607-14921-02S
1

GE40/CR42 (MS-1492) Disassemble Guide
■6、LOWER CASE ASSY
6.7：Remove the left Power cable.
6.8：Remove the Hall Switch cable.
6.9：Remove the Power board.
Component
P/N
Qty
Power board
607-1492B-01S
1