MSI MS-1722 - Whitebook ID1 - 17 User manual

GX720 （MS-1722）Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■3、THERMAL-KIT And CPU Module
■ 4、RAM、WLAN And TUNER Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■10、LCD MODULE ASSY

GX720（MS-1722）Disassemble SOP
■ 1、Battery Pack
1-1：Push the battery Unlock button as below;
1-2：Push the battery Release button as below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-1566210-SJ3 1

GX720（MS-1722）Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1：Remove the following 5pcs M2.5*5mm screws with Screw Driver.
Note：Screw driver torque is 2.0~2.5kgf.cm
2-2：Remove Bottom Door Assy as below;
NO. Part Name Part No. Qty
1Screw E43-I250551-H29 5
2BOTTOM DOOR ASSY 307-721J211-Y31 1

GX720（MS-1722）Disassemble SOP
■ 3、THERMAL-KIT And CPU Module
3-1：Remove 4pcs M2.5*5mm screws, CPU Fan sink Cable and CPU Fan.
Note：Screw driver torque is 2.0~2.5kgf.cm
Cable
41
3
2
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 4
2 CPU FAN E33-0800050-F05 1

GX720（MS-1722）Disassemble SOP
3-2：Remove the following 4pcs M2.5*5mm screws, then remove CPU Thermal Module as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
3
2
4
1
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 4
2 CPU Thermal Module E31-0800610-F05 1

GX720（MS-1722）Disassemble SOP
3-3：Remove 4pcs M2.5*5mm screws, Then remove MECH HEATSINK as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
1
2
3
4
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 4
2 MECH HEATSINK E31-0403610-F05 1

GX720（MS-1722）Disassemble SOP
3-4：Open the CPU Slot ;
3-5：Remove CPU Module as below;
NO. Part Name Part No. Qty
1 CPU Module A09-2420176-I06 1

GX720（MS-1722）Disassemble SOP
3-6：Remove 2pcs M2.5*5mm screws, Then remove VGA Card Module as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 2
2 VGA card 602-V114-01S 1

GX720（MS-1722）Disassemble SOP
■4、RAM、WLAN And TUNER Module
4-1：Push the RAM locks away;
4-2：Take off the RAM Module as below:
NO. Part Name Part No. Qty
1 RAM Module S7C-S346801-T10 2

GX720（MS-1722）Disassemble SOP
4-3：Remove 1pcs M2*3mm screw, and then remove ANTENNA/HIGH-TEK/R-L as below;
Note：Screw driver torque is 1.0~1.5kgf.cm
1
4-4：Remove WIRELESS CARD as below;
NO. Part Name Part No. Qty
1Screw E43-1303501-H29 1
2WIRELESS CARD S57-0800180-I06 1