MSTR BRAND RACK SK-SWING User manual

INSTRUCTION MANUAL
V1
Swing Arm Wall Mount Accessory for RACK SK14,SK28 and SK38
RACK SK-SWING

2
Required Tools
13mm
(1/2 in.)
5.5mm
(7/32 in.)
10mm
(3/8 in.)

3
Supplied Parts
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your
dealer; contact Customer Service. Never use damaged parts!
[01] x 2
[02] x 8 [03] x 8 [04] x 8
5/16 x 3½ in.
[05] x 4 [08] x 2
[07] x 4
[06] x 1

4
guration best
suits your needs. Attach the rack arm
of both swing arms [01] to the back
brace of the rack using carriage bolts
[02], washers [03], and lock nuts [04].
The swing arms [01] can be mounted
guration or a right
guration.
Attach Swing Arm to Rack Assembly
Left Hinge Right Hinge
[01]
[01]
[02]
[03]
[04]
[01]
[01]

5
12
Locate studs. Verify the center of the stud with an
nder.
CAUTION: Avoid potential personal injuries
and property damage!
ÙAny material covering the wall must not
exceed 16 mm (5/8 in.).
ÙMinimum wood stud size: common 2 x 4 in
(nominal 1½ x 3½ in).
rst lag
bolts on the center line of the stud
564 mm
41 cm
(16 in.)
Mounting to Wall (Wood stud)
(22.2in)
 

6
3 4 Start hinge side lag bolts [05]. Leave
approximately 13 mm (1/2 in.) of
space from the bolt head to the wall.
Drill pilot holes as illustrated.
CAUTION: Improper use
could reduce the holding power
of the lag bolt. To avoid potential
injuries or property damage:
pilot holes MUST be drilled to a
depth of 89 mm (3½ in.), using a
5.5 mm (7/32 in.) diameter drill
bit.
89 mm
(3in.)
5.5 mm
(7/32 in.)
[05]
[05]
13mm
(1/2 in.)
13 mm
(1/2 in.)

7
5Hang swing arm/rack assembly onto the lag
bolts [05].
[01]
[01]
[05]
[05]

8
7Tighten lag bolts [05] only until the washers [06]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.
)
[05]
[05]

9
89Tighten lag bolts [05] only until the washers [07]
rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
Drill through the top slots of the wall arms [01]
into the center of the next stud.
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage: pilot holes MUST be
drilled to a depth of 89 mm (3½ in.), using a 5.5
mm (7/32 in.) diameter drill bit.
89 mm
(3½ in.)
[01]
[01]
5.5 mm
(7/32 in.)
[01]
[01] [05]

10
12
406.6 mm
(16 in.)
Mark the locations for the lag bolts on the
corners of a rectangle measuring 406.4 (16 in.)
Drill pilot holes as illustrated.
CAUTION: To avoid potential injuries or
property damage:
ÙPilot holes MUST be drilled to adepth of 89 mm
(3½ in.) using a 10 mm (3/8 in.) diameter drill bit.
ÙNever drill into the mortar between blocks.
ÙMinimum solid concrete thickness: 8 in.
ÙMinimum concrete block size: 8 x 8 x 16 in.
89 mm
(3½ in.)
10 mm
(3/8 in.)
Mount to Wall (solid concrete or concrete block)
 
(22.2in)
564 mm