MULTIQUIP Diamond Back SP303516 Street Pro Guide

OPERATION AND PARTS MANUAL
SP3 “STREET PRO”
PROFESSIONAL SLAB SAW
35 HP WISCONSIN DIESEL ENGINE
MODELS
SP303516, SP303520, SP303526
SP303530
Revision #3 (09/29/06)
THIS MANUAL MUST COMPANY THE EQUIPMENT AT ALL TIMES.
Diamond Back
To find the latest revision of this
publication, visit our website at:
www.multi
q
ui
p
.com

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 1
MQ SP-3035 CONCRETE SAW
PROPOSITION 65 WARNING

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 2
MQ SP-3035 CONCRETE SAW
SILICOSIS /RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
WARNING
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
WARNING
SILICOSIS WARNING RESPIRATORY HAZARDS

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 3
MQ SP-3035 CONCRETE SAW
Table of Contents
PROPOSITION 65 WARNING .......................................................................................1
SILICOSIS /RESPIRATORY HAZARDS......................................................................2
PARTS ORDERING PROCEDURES........................................................................... 6
SAFETY..............................................................................................................................7
HAZARD SYMBOLS.................................................................................................... 8
GENERAL SAFETY WARNINGS ....................................................................................... 11
BLADE SAFETY......................................................................................................... 13
SAW TRANSPORTATION SAFETY......................................................................... 14
EMERGENCIES .......................................................................................................... 14
MACHINE OPERATION AND SAFETY DECALS................................................... 15
SERIAL TAG ................................................................................................................... 16
OPERATION ...................................................................................................................17
BEFORE STARTING......................................................................................................... 17
CONTROL PANEL ........................................................................................................... 18
ENGINE POWER,CUTTING POWER &SHEAVE SIZE........................................................ 19
INSTALLING THE BLADE,BLADE GUARD &BLADE FLANGE ......................................... 20
REMOVING THE BLADE,BLADE GUARD &BLADE FLANGE........................................... 21
STACKING BLADES FOR WIDE CUTS.............................................................................. 22
INSTALLING AND REMOVING THE BLADE GUARD.......................................................... 23
WATER SUPPLY AND CONTROL ..................................................................................... 26
HANDLEBARS................................................................................................................. 27
FUELING THE SAW ......................................................................................................... 28
STARTING AND STOPPING THE ENGINE .......................................................................... 29
POINTER ADJUSTMENT .................................................................................................. 30
RAISE –LOWER CONTROLS ........................................................................................... 31
SETTING THE DEPTH GAUGE &DEPTH STOP ................................................................. 32
DRIVE SYSTEM .............................................................................................................. 33
NIGHT LIGHT ................................................................................................................. 36
TRANSPORTATION TIE-DOWNS AND LIFT POINT ............................................................ 37
OPERATION ON A SLOPE OR INCLINE.............................................................................. 38
FREEING A STUCK BLADE.............................................................................................. 38
DRAINING THE WATER SYSTEM..................................................................................... 39

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 4
MQ SP-3035 CONCRETE SAW
MAINTENANCE.............................................................................................................40
REMOVABLE GUARDS AND ACCESS PANELS.................................................................. 40
BELTS AND PULLEYS ..................................................................................................... 41
BLADE FLANGE REMOVAL/INSTALLATION .................................................................... 45
CIRCUIT BREAKERS ....................................................................................................... 50
MAXIMUM CUT DEPTH ADJUSTMENT............................................................................ 50
LUBRICATION ................................................................................................................ 51
ENGINE MAINTENANCE ................................................................................................. 52
RAISE-LOWER SYSTEM.................................................................................................. 53
CONTROL HANDLE ADJUSTMENT .................................................................................. 54
HYDRAULIC SYSTEM ..................................................................................................... 55
POSITRACTION ADJUSTMENT......................................................................................... 60
EXPLANATION OF CODE IN REMARKS COLUMN.............................................61
SUGGESTED SPARE PARTS.......................................................................................62
COMPONENT DRAWINGS..........................................................................................63
NAMEPLATE AND DECALS ASSY.................................................................................... 63
DECK/GAUGE PANEL ASSY. .......................................................................................... 65
CONSOLE/SHEET METAL ASSY...................................................................................... 67
ACCESS PANEL ASSY..................................................................................................... 69
FUEL TANK ASSY. ......................................................................................................... 71
F-N-R CONTROL HANDLE ASSY.................................................................................... 73
JOYSTICK MOUNTING ASSY........................................................................................... 75
LIFT PUMP CIRCUIT ASSY.............................................................................................. 77
WATER SYSTEM ASSY................................................................................................... 79
DEPTH INDICATOR ASSY................................................................................................ 81
HANDLE AND LIGHT ASSY............................................................................................. 83
FRONT/REAR POINTER ASSY. ........................................................................................ 85
GAUGES AND CONTROLS ASSY...................................................................................... 87
FRONT AXLE ASSY. ....................................................................................................... 89
DEPTH STOP ASSY......................................................................................................... 91
PLATFORM ASSY............................................................................................................ 93
DRIVE ASSY................................................................................................................... 95
BLADESHAFT AND MOUNTING ASSY. ............................................................................ 97
POSITRACTION ASSY...................................................................................................... 99

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 5
MQ SP-3035 CONCRETE SAW
PULLEY AND V-BELT ASSY......................................................................................... 101
BATTERY ASSY............................................................................................................ 103
ENGINE BRACKETS ASSY............................................................................................. 105
ENGINE INSTALLATION ASSY....................................................................................... 107
BLADEGUARD ASSY..................................................................................................... 109
OPTIONAL WATER PUMP KIT ASSY............................................................................. 111
COLLAR PULLER ASSY................................................................................................. 113
SEAL SLEEVE PULLER/SEAL INSTALLATION TOOL ...................................................... 115
BUSHING EXTENSION KITS .......................................................................................... 117
ELECTRIC SCHEMATIC...........................................................................................119
SPECIFICATIONS........................................................................................................120

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 7
MQ SP-3035 CONCRETE SAW
SAFETY
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

NOTE
This Owner's Manual has been developed to provide instructions for the
safe and efficient operation of the Multiquip SP-3035 CONCRETE SAW.
For engine maintenance information, please refer to the engine
manufacturers’ instructions for data relative to its safe operation.
Before using this CONCRETE SAW, ensure that the operating individual
has read and understands all instructions in this manual.
Safety precautions should be followed at all times when operating this equipment. Failure to read and
understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you about potential hazards that could
injure you or others. The Safety Messages specifically address the level of exposure to the
operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.
DANGER
DANGER: You WILL be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
WARNING
WARNING: You CAN be KILLED or SERIOUSLY injured if you
DO NOT follow directions.
CAUTION
CAUTION: You CAN be injured if you DO NOT follow directions.
Potential hazards associated with SP-3035 Concrete Saw operation will be referenced with "Hazard
Symbols" which appear throughout this manual, and will be referenced in conjunction with Safety
"Message Alert Symbols".

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 8
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS

Explosive Fuel
Gasoline is extremely flammable, and its vapors can cause an
explosion if ignited. DO NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank while the engine is
running or hot. DO NOT overfill the tank, since spilled fuel could
ignite if it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in well-
ventilated areas and away from sparks and flames. NEVER use
fuel as a cleaning agent.
Burn Hazards
Engine components can generate extreme heat. To prevent
burns, DO NOT touch these areas while the engine is running or
immediately after operations. NEVER operate the engine with heat
shields or heat guards removed.

Rotating Parts
NEVER operate equipment with covers, or guards removed. Keep
fingers, hands, hair and clothing away from all moving parts to
prevent injury.
Accidental
Starting
ALWAYS place ON/OFF switch to the OFF position, remove key
and/or disconnect the spark plug leads before servicing the
engine, equipment, or supporting components. Ground the lead to
prevent sparks that could ignite a fire.
Lethal Exhaust
Gases
Engine exhaust gases contain poisonous carbon monoxide. This
gas is colorless and odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined area or enclosed
structure that does not provide ample free flow of air.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 9
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS
Over Speed
NEVER tamper with factory settings of engine governor or speed
settings. Ensure the proper Speed Kits are installed to safely
support the prescribed RPM settings for diamond blade
operations.
Guards and
Covers in Place
NEVER operate the saw without blade guards and covers in
place. Adhere to safety guidelines ANSI American National
Standards Institute, OSHA, and/or other applicable local
regulations.
Rotating Blade
Rotating Blade can cut, tear, and crush. Keep hands and feet
clear.
Respiratory
Hazard
ALWAYS wear approved respiratory protection.

Sight &
Hearing Hazard
ALWAYS wear approved eye and hearing protection.
Crush Hazard
CRUSH AND PINCH HAZARD Keep hands and feet clear.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 10
MQ SP-3035 CONCRETE SAW
HAZARD SYMBOLS
Skin Injection
Hazard
NEVER use your hand to find hydraulic leaks. Use a piece of wood
or cardboard. Hydraulic fluid injected into the skin must be treated
by a knowledgeable physician immediately or severe injury or death
can occur.

NOTE
Text set off like this presents clarifying information, specific
instructions or commentary designed to help prevent damage to
your saw, other property, or the environment.
Other important messages are provided throughout this manual to
help prevent damage to your concrete saw, other property, or the surrounding
environment.
CAUTION
Equipment Damage Message
Other important messages are provided throughout this manual
to help prevent damage to your concrete saw, other property, or
the surrounding environment.

NOTE
This concrete saw, other property, or the surrounding environment could be
damaged if you do not follow instructions.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 11
MQ SP-3035 CONCRETE SAW
General Safety Warnings
Most accidents involving product operation, maintenance and repair are caused by failure to
observe basic safety rules and precautions. Accidents can often be avoided by recognizing
potentially hazardous situations before an incident occurs.
WARNING
Before operating the saw, make sure all protective guards are securely
in place. All saws are supplied with a blade guard, collar guard and belt
guard.
Whenever necessary, replace operation and safety decals if they
become difficult to read
Verify the engine start switch is set to the OFF position before installing
a blade.
Make sure the operator knows how to turn the engine OFF in case of
an emergency.
Do not go near rotating parts (blades, belts, pulleys or wheels) while
engine is running.
Muffler and exhaust gases are extremely hot. Stay clear of muffler and
exhaust gases. Allow these parts to cool before servicing the saw.
Stay clear of the saw while it is being hoisted.
Anytime the saw is lifted onto its nose, or tilted fully back, for
maintenance access, the high end MUST be blocked up to prevent the
possibility of crush injury!
Allow the engine to cool before adding fuel or performing service and
maintenance functions. Contact with HOT components can cause
serious burns.
Never operate the saw in any enclosed or narrow area where free flow
of air is restricted. If the airflow is restricted it will cause serious
damage to the saw’s engine and may cause injury to people.
Remember the saw’s engine gives off DEADLY carbon monoxide gas.
ALWAYS refuel in a well-ventilated area; away from sparks and open
flame. Avoid “topping off” the filler port as spills can result.
ALWAYS use extreme caution when working with flammable liquids.
When refueling, STOP the engine and allow it to cool.
NEVER smoke around or near the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled on a HOT engine.
NEVER operate the saw in an explosive atmosphere where fumes are
present or near combustible materials. An explosion or fire could
result causing severe bodily harm or even death.
NEVER use fuel as a cleaning agent.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 12
MQ SP-3035 CONCRETE SAW
General Safety Warnings
WARNING
ALWAYS read, understand, and follow procedures in the Operator’s
Manual before attempting to operate the equipment.
Be sure the operator is familiar with proper safety precautions and
operating techniques before using the saw.
Make sure the operating area is clear before starting the engine.
Maintain this equipment in a safe operating condition at all times
Keep the saw clean. It will work better and last longer
Use proper blades and follow the blade manufacturer’s
recommendations. Match blade rpm (Spindle rpm) to recommended
blade surface feet per minute (SFPM).
Tighten the 5/8” blade-mounting bolt to 100-125 foot-lbs. torque.
Turn engine OFF prior to fueling the saw!
Start engine with the joystick in NEUTRAL to prevent unexpected saw
movement.
Do not leave saw unattended while engine is running.
Do not start engine on a sloping surface to prevent unexpected loss of
control.
Do not park or leave saw unattended on a slope - the saw can roll when
the engine is OFF. Block the unit when leaving.
If the saw must be parked on a slope, turn it across the angle of the
slope, to prevent accidental downhill movement.
Prior Always store equipment properly when not being used. Equipment
should be stored in a clean, dry location out of the reach of children.
When storing the saw in freezing weather, blow out water lines to
prevent damage to components in the water delivery system.
Prior to service, level the frame surface.
Do not over tighten the Spindle drive belt
Turn on water flow prior to starting the engine, to prevent damage to the
impeller of a belt-driven water pump.
Don’t pollute! Waste oils and other chemicals must be disposed of in a
manner consistent with local and state environmental protection
regulations.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 13
MQ SP-3035 CONCRETE SAW
BLADE SAFETY
WARNING
ALWAYS inspect diamond blades before each use.
The blade should exhibit no cracks, dings, or flaws in
the steel centered core and/or rim. Center (arbor)
hole must be undamaged and true.
Examine blade flanges for damage, excessive wear
and cleanliness before mounting blade. Blade should
fit snugly on the shaft and against the inside/outside
of the saw.
Only cut the material that is specified by the blade.
Read the specifications of the blade to ensure the
proper tool has been matched to the material being
cut.
ALWAYS keep blade guards in place. Exposure of
the blade must not exceed 180 degrees.
Ensure that the blade does not come into contact
with the ground or surface during transportation. DO
NOT drop the blade on the ground or surface.
The engine governor is designed to permit maximum
engine speed in a no-load condition. Speeds that
exceed this limit may cause the blade to exceed the
maximum safe allowable speed.
Ensure that the blade is mounted for proper
operating direction.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 14
MQ SP-3035 CONCRETE SAW
SAW TRANSPORTATION SAFETY
WARNING
Use appropriate lifting equipment to ensure the safe
movement of the saw.
DO NOT use the handle bars and/or front pointer as lifting
points.
NEVER attempt to tow the untrailered saw behind a vehicle.
NEVER transport the saw with the blade mounted.
EMERGENCIES
WARNING
ALWAYS know the location of the
nearest fire extinguisher.
ALWAYS know the location of the
nearest first aid kit.
In emergencies always know the
location of the nearest phone or
keep a phone on the job site.
Know the phone numbers of the
nearest ambulance, doctor, and fire
department. Knowing this information
is invaluable in the case of an emergency
and could keep a serious situation from
becoming a tragic one.

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 15
MQ SP-3035 CONCRETE SAW
MACHINE OPERATION AND SAFETY DECALS
The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should
any of these decals become unreadable, replacements can be obtained from your dealer.
Fig. 1 — Decals
Nesfaer dfgat
the sfarbs in
saccty guizcin
cbccR) 19b4
Nesfaer dfg
the sfarbs i
Nesfaer df
the sfarbs i
n pbb
Nesfaer dfgate ths
the sfarbs i
Neer dfgate ths
the sfarbs in pbb
Nesfar dfgate ths
tfarbs in pbb
Nasfsaer dfghhte thsfaw wiot
Nasfsaer dfghhte thsfaw wiot
Nasfsaer dfghhte thsfaw wiot
Nasfsaer dfghhte thsfaw wiot
SMI
WARNING
KEEP HANDS
CLEAR
WARNING!
KEEP FEET
CLEAR
WARNING
When Larger Blade and Guard
is Installed, Belt Drive MUST
Be Changed to Proper Size.
See Owners Manual.
S.M.I. MASONRY AND CONCRETE
SAW MANUFACTURER’S INSTITUTE
CAUTION
FAILURE TO COMPLY WITH THE C C AH
JADV EEE AV EEA OIEJGGVCBVVZ
P/N 25249-001
P/N 22122-001
P/N 604001
P/N 604000
P/N 23330-001
P/N 25250-001
P/N 606004
P/N 36099 (ISO Blue)
P/N 25483
(small)
P/N 25782
DECAL SHEET INTL STDS
P/N 11246
LUBRICATION
CHECK HOT BELT DRIVE
P/N 13118
P/N 25491 P/N 25678
CONTACT MULTIQUIP
SERVICE DEPARTMENT
MODEL
SERIAL NO.
P
O
W
D
E
R
C
O
T
E
D
A
R
O
T
A T
I
O
N
R
O
T
A T
I
O
N
P/N 35137
P/N 21571
1-1/2” x 2-1/4”
P/N 20525
To avoid injury,
you MUST read
and understand
operator’s manual
before using this
machine.
Ask for training
as needed.
This machine to
be operated by
qualified
personnel only.
P/N 35137
WARNING

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 16
MQ SP-3035 CONCRETE SAW
Serial Tag
Fig. 2 — Serial Tag

NOTE
For future reference, fill in the model number and serial number of
your saw in the space above.
The serial tag contains the model number and serial number of the saw. This information details
all parts that were included with the saw when it was shipped from the factory, as well as the date
of manufacture.
Record your ENGINE model number, spec. number and serial number here:
MODEL NO. SPEC. NO. SERIAL NO.
The serial tag is bonded to the inside panel of the console.
Fig. 3 — Serial Number Locations
Serial Tag
Engine
Serial
Numbers

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 17
MQ SP-3035 CONCRETE SAW
OPERATION
Before Starting
Walk around the saw and ensure that all guards
and panels are properly installed.
Wear eye and hearing protection.
Wear protective clothing.
1. Check engine and hydraulic oil.
2. Verify the proper-sized blade guard is fully installed on the blade guard mounting tab.
3. Adjust handlebars for best operator control.
4. If a belt driven water pump is installed, turn on the water flow before starting the engine.
Fig. 4 — Guards & Panels
Blade Guard
Flange
Belt Guard
Console
Access Panel
Rear Access
Panel
Handlebars

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 18
MQ SP-3035 CONCRETE SAW
Control Panel
Fig. 5 — The Control Panel
Auxiliary
Switch
Voltmeter
T
hrottle
Engine On-
Of
f
-Start
Plunge
Button
Operating
Instructions
Speed Control
Joystick
Safety
Warnin
g
s Water
Pump
Switch
Maintenance
Information
Water
Flow
Control
Choke
Depth
Gau
g
e
Depth Gauge
Zero
Fuel
Tank
Cap
Positraction
Control
Drive
Disengage
Engine
Tach Light Switch

MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAGE 19
MQ SP-3035 CONCRETE SAW
Engine Power, Cutting Power & Sheave Size
Blade Size & Configuration per Model
The SP-3035 is available in four Blade Speed configurations. The following chart shows the
various configurations for each model.
Blade
Size
Model Engine
RPM No
Load
Spindle
RPM No
Load
Governor
Setting
(Hole
Number)
Ratio
Kit
Engine
Pulley
Part
Number
Engine
Pulley
Size
Spindle
Pulley Part
Number
Spindle
Pulley
Size
Surface
Feet Per
Minute
16" Q303516 3000 3000 12 25603 540000 3.8" 540006 3.8" 12566
20" Q303520 2520 2800 9 25849 540070 3.6" 540066 4.0" 13195
26" Q303526 2000 2800 7 35103 540012 3.0" 540065 4.2" 13614
30" Q303530 1773 2600 5 35104 540012 3.0" 540049 4.4" 13923
When choosing a blade for your cutting conditions, follow the blade manufacturer’s
recommendations. Match blade RPM (Spindle RPM) to the recommended blade Surface Feet Per
Minute (SFPM).
SFPM 12” dia.
RPM 14” dia.
RPM
16” dia.
RPM 18” dia. RPM 20” dia.
RPM
24” dia.
RPM 26” dia.
RPM
30”
dia.
RPM
8,000 2546 2183 1910 1698 1528 1273 1175 1019
8,500 2706 2319 2029 1804 1623 1353 1249 1082
9,000 2865 2456 2149 1910 1719 1432 1322 1146
9,500 3024 2592 2268 2016 1814 1512 1396 1210
10,000 3183 2728 2387 2122 1910 1592 1469 1273
10,500 3342 2865 2507 2228 2005 1671 1543 1337
11,000 3501 3001 2626 2334 2101 1751 1616 1401
11,500 3661 3138 2745 2440 2196 1830 1690 1464
12,000 3820 3274 2865 2546 2292 1910 1763 1528
12,500 3979 3410 2984 2653 2387 1989 1836 1592
13,000 4138 3548 3104 2759 2483 2069 1910 1655
WARNING
NEVER tamper with factory settings of engine governor
or speed settings. Ensure the proper Speed Kits are
installed to safely support the prescribed RPM settings
for diamond blade operations.