MULTISPAN UTC-4201A User manual

J: 0 to 600°C / K: 0 to 1200°C /
PT-100: -99 to 400ºC /PT.1: -99.0 to 400.0°C
PID
Output 1
Output 2
Power Supply
0 To 10VDC
1 Relay (High/Low/Inband/Outband Alarm mode Selectable)
100 to 250V AC, 50 / 60 Hz smps
Model
Display
Size
Panel Cutout
Input
Temperature
Range
Control Action
44 X 44
48 X 48 X 95
UPPER:- 4 Digit 7 seg .39”,red LED Display
LOWER:- 4 Digit 7 seg .28”,green LED Display
UTC-4201A
J, K, PT-100 (selectable)
OPERATING MANUAL
TEMPERATURE CONTROLLER WITH ANALOG OUTPUT
www.multispanindia.comPage - 1
Technical Specification
Note :
1) Press + key for 3 sec to go to Factory Setting mode.
2) Press key to go to next parameter.
3) Press or to enter value or to select option.
4) Every time the instrument is turned ON, following pattern will be displayed
5) When manual mode selected, using & key, we can enter output value
0 to 10V DC.
UTC-4201A
All digit segment will be turned ON for 3 sec
Previous or default sensor input will be display for 2 sec
Process Value
Set Value


   

R1
R2



www.multispanindia.com
Page - 2
BASIC CONFIGURATION
SET POINT SETTING SET VALUE
SET POINT-2
SET POINT-1


 Password Message




Press key for 5 sec to enter Password
parameter
SET
 PROCESS VALUE
 Input ( J / K / Pt100 / Pt.1 )
Control Action
Control Mode
Heat/Cool selectable
Individual / Relative


 Password Message
Press ENT key to Save & Exit




  .K
SET
Set Point Low Limit
Set Point High Limit
H-AL,L-AL,Inband,Outband, OFF Selectable






OFF-SET


TO ENTER BASIC
CONFIGURATION
SETTING, ENTER “73”



 Password Message

PID














Manual Reset
Hysteresis
Output Scaling
Low Percentage
High Percentage
Mode Selection
Auto/Manual








Parameters
Proportional
Constant
Integral
Constant
Derivative
Constant
Cycle Time
CONTROL PARAMETER
2)
3) Press key to go to next parameter. Press or key to enter value or to
select option.
1) Press key to enter into an internal setting
Note :
TO ENTER CONTROL
PARAMETER
SETTING, ENTER “37”
Press ENT key
to Save & Exit
www.multispanindia.com Page - 3

Off-set correction
Output Scaling
Low Percentage
High Percentage
Mode Selection
-20.0°C to +20.0°C
-20°C to +20°C
Forward /Reverse Sele.
00 to high percentage
Low percentage to 100
Auto/Manual
CT 4 sec to 99 sec
IC 0.000 to 9.999
MR
Hysteresis -9.0 to +9.0
0.1°C to 50.0°C
-9 to +9
1°C to 50°C
DC 0 to 9999
PC
Sr.
1
2
3
4
5
6
7
8
9
10
11
00.00 to 99.99
Parameter Range for PT.1 sensor
Range for J, K, PT100
Product improvement and upgrade is a constant procedure. So for more updated operating information and support, please
contact our Helpline : 9978991474/75 or Email at [e-mail] www.multispanindia.com
Page - 4
FACTORY SETTING
FACTORY SETTING
PARAMETER
IC
Output scaling Forward
000%
100%
Auto
CT
High (%)
OFFSET
Mode
PC
DC
Low (%)
MR
VALUES
0.225
6 sec
05.00
25
0°C
0°C
SR.
2
7
4
9
6
10
1
3
8
5
Process Value
Set Value
Factory Setting
Press + key for 3 sec
1) Connection Diagram with Relay Output.:
N
L
C
-
+
Relay
NO
O/P
NC