Munters MWI Series User manual

7
10
3
2
1
4
5
6
9
8
11
MWI
Side Wall Inlet
1
Quick Assembly Guide
Parts List:
Item Part Name/Description QTY/
Inlet
QTY/
Box
1 Left Side Support 1 6
2 Right Side Support 1 6
3 Top header 1 6
4 Bottom header 1 6
5 Door, curved 1 6
6 Left side door, end cap 1 6
7 Right side Door, end cap 1 6
8 Gasket seal 2 12
9 Metal Guard 1 6
10 Rubber seal 1 6
11 L-screw hook 2 12
Ag/MIT/IGB-2414-12/18 Rev 6.0
NOTE: The following guidelines should be used and closely followed when assembling and installing MWI.
In order to assure proper performance and correct functioning of the inlets, the installer must understand the importance of quality construction-work and use
quality materials. Attention to details relating the assembly work, proper sealing or prevention of air leaks is a must and must be undertaken by the installer.
WARNINGS: Do not overtighten the screws! Tighten until flush. Do not dent the housing! Overtightening the screws will result in damage to MWI.
!
WARNING:
DO NOT use metal hammer to secure the MWI. The use
of a metal hammer can result in damage to MWI.
Insert top and bottom
headers into the right-side
lateral support.
1
Slide the curved louver in
the bottom header slot.
2
Slide the metal grid in the
headers slot.
3
Insert the rubber seal in
the top header slot and
along door sides.
6
Properly secure the MWI
lateral supports using a
rubber mallet.
Use caution!
5
Slide insert the left side
lateral support.
4

Ag/MIT/IGB-2413-12/18 Rev 6.0
2
Place the inlet into framed
opening. NOTES: the opening size
is critical! Leave always a gap of
0.2inch or 5mm evenly distributed
around the unit.
Fasten the left and right lateral
side support using appropreite
screws (2-inch or 5 cm). NOTES:
Fastening points are marked on both
supports. Screws and fittings are not
included, Choose screws and fittings
that are suited to the material in the
wall and have sufficient holding
power.
Fasten the bottom header
profile using appropriate screw.
NOTES: Fastening should be done in
the center, on the marked line. Make
sure the bottom header is straight
(linear) when fastening.
Push slightly up on the top
header center, 0.25 inch or 0.6
cm. needed difference.Fasten
the top header profile using
appropriate screw. NOTES:
Make sure the slight curvature of
approximately 0.25 inch or 0.6 cm is
achieved before fastening. Fastening
should be done in the center, on the
marked line.
Verify the correct movement,
opening and closing of the inlet.
Fasten the (2) L-Screw hooks
evenly spaced above header.
Place 0.5 inch or 1.2 cm above
the top header, opposite to the
direction of pull.
NOTES: Avoid interference with the
pulling cable or rod.
Install a small pulley at the top
of the inlet. NOTES: Pulley or fitting
are not included.
12 3 4
567
Pass the string through the
hole in the curved louver then
through the pulley, twords the
direction of pulling force. Fix
the string to the main pull cable
or rod using clamp.
8
Item description Inlet Size Framed Opening Size Should be 0.5inch or 1.2cm
larger than the inlet size
Color W x H x D W x H (±0.06inch or ±0.2cm)
White Black inch cm inch cm
MWI 4413 W MWI 4413 B 44 x 13 x 4 111.8 x 33 x 10 44.5 x 13.5 113 x 34.3
MWI 4408 W MWI 4408 B 44 x 8.25 x 4 111.8 x 21 x 10 44.5 x 8.75 113 x 22.2
MWI 4113 W MWI 4113 B 41 x 13 x 4 104.1 x 33 x 10 41.5 x 13.5 105.4 x 34.3
MWI 4108 W MWI 4108 B 41 x 8.25 x 4 104.1 x 21 x 10 41.5 x 8.75 105.4 x 22.2
MWI 3413 W MWI 3413 B 34 x 13 x 4 86.4 x 33 x 10 34.5 x 13.5 87.6 x 34.3
MWI 3408 W MWI 3408 B 34 x 8.25 x 4 86.4 x 21 x 10 34.5 x 8.75 87.6 x 22.2
10
After the actuator & wire-rope or rod system are
installed, re-adjust all MWI properly to assure correct
opening and closing.
Australia Phone [phone], [e-mail], Brazil Phone [phone],
[email protected], Canada Phone [phone], [e-mail], China Phone
[phone], [e-mail], Denmark Phone [phone], [e-mail],
Germany +49 (0) 25 58 - 93 92-0, India Phone [phone], [e-mail], Indonesia
Phone [phone], [e-mail], Israel Phone [phone], [e-mail],
Italy Phone [phone], [e-mail], Japan Phone [phone], mkk@munters.
jp, Korea Phone [phone], [e-mail], Mexico Phone [phone],
[e-mail], Singapore Phone [phone], [e-mail], South Africa
and Sub-Sahara Countries Phone [phone], [e-mail], Spain Phone +39
0183 5211, [e-mail], Sweden Phone [phone], [e-mail], Thailand Phone
[phone], [e-mail], Turkey Phone [phone], [email protected],
USA Phone [phone], [e-mail],
Export & Other countries Phone [phone], [e-mail]
9
Caulk all sides four internal edges of the MWI after
installation using a caulk gun. NOTE: Mounting hardware,
silicone and caulk gun are not included.WARNING: Do not
use expandable foam to seal the edges of MWI! The use of
expandable foam can result in damage of MWI.
MWI
Side Wall Inlet
Quick Assembly Guide