Murideo Prisma User manual

Page
1
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Murideo
Prisma
Networked Video Processor and 3D LUT
User’s Manual
Version 1.00

Page
2
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Important Safety Information
•Follow all instructions
•Use only a dry cloth to clean
•Indoor use only: To reduce the risk of electric shock, do not use near water or expose to
rain or moisture. Keep away from excess moisture
•Do not use near heat sources such as room heaters, hot A/V equipment
•Read all warnings
•Use only accessories provided by Murideo
•Unplug the device during lightning storms or when unused for long periods of time
•Keep away from open flames
•Protect all connected cords including power cords from being pinched, compressed, and
stepped on
•Do not open the case. All servicing should be done only by qualified and approved service
personnel and will void the warranty.
•Electrical Input Rating: Power over 12V/DC 500mA. Caution: Use only the supplied AC/DC
Adapter
•Operating temperature range: e.g. 0 to 40C.
•To disconnect power sources, remove the AC/DC adapters from the wall outlets.

Page
3
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Table of Contents
Page 4 Overview
Page 4 Key Features
Page 4 What's in the Box
Page 5 Functionality Diagram
Page 6-8 Connecting the Prisma
•Manual Operation
•Operation with 3rd Party Software
•Operation with WebOS
Page 8 Advanced Use of Prisma
Page 9-12 Creating a LUT
Page 13-16 Frequently Asked Questions
Page 17 FCC Compliance
Page 18-20 Warranty
Page 21 Getting Help
Page 22-29 Appendix A: Creating CalMAN 3D LUTs ~ Overview Guide
Page 30 Appendix B: Documents Coming Soon

Page
4
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Overview
The Prisma is a highly advanced single-in,single-out video processor with network control. Other
processors have similar features individually, but none of them can do it all like the Prisma. The
Prisma’s 17x17x17 3D LUT and PrismaVue technology give unparalleled control over image fidelity.
The Prisma's rich and capable feature set will appeal to everybody that appreciates great video.
Supported by SpectraCal - CalMAN, Light Illusion - Light Space and Argyle color management
software packages
Key Features:
•Complete color calibration using a 17x17x17 LUT (Look Up Table)
•PrismaVue enhances picture detail and reduces compression artifacts
•Accurate display and color matching.
•For video production, the Prisma can load common 3D LUT tables for reproducing specific
looks and adjusting raw footage colors.
•For Digital Signage, the Prisma can accurately match colors between panels.
•For control and automation the Prisma features a modern built in web server and http API.
What’s in the Box?
•PRISMA
•IR Remote
•IR Receiver
•1.5 ft HDMI Cable
•7 ft Ethernet Cable
•12V DC/AC Power Supply / Charger (110-240 VAC)
Please read the entire manual before turning on your new Murideo PRISMA for helpful tips.

Page
5
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Rear Panel Functions:
Left to right above
1. IR-In - connect supplied IR receiver if you plan on using the supplied remote control
2. Ethernet - connect supplied Ethernet cable to the local network with DNS server (your
home network).
3. Out - connect HDMI cable between out port and display.
4. Out Link – indicates a display is detected.
5. In Link – indicates a source is present.
6. In – connect output of source to In port
7. +5V – connect supplied wall wart between wall outlet (110-240V) and Prisma
8. PWR – indicates power is present.

Page
6
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Connecting the Prisma
1. Prisma can be operated manually using the IR Remote and IR Receiver (supplied).
2. Prisma can be used with the following program for creating LUTs
a. Spectracal’s CalMan version 5.6 or greater.
b. Light Space – Light Illusion
c. Argyll (Shareware)
3.
For loading LUTs and basic and advanced control of Prisma you can connect via LAN –
http://prisma-XXXX.local (Mac) or http://prisma-XXXX (PC) – where XXXX is the last 4 digits
of the serial number. See bottom of unit for serial number or outside of box. Once URL
above is entered a WebOS will be displayed.
Manual Operation Connection
Option 1 – Use the included remote IR remote control. You have access to stored LUTs and
PrismaVue adjustment.

Page
7
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Light Meter
3rd Party Connections:
You will need a PRISMA, a PC with a licensed copy of 3rd party software like CalMan or Argyll
installed, a light measurement meter, and cables. (Contact AVPro if you need a current License or
details when other calibration software will be PRISMA supported.)
1. Connect the supplied AC power adapter to the PRISMA.
2. Connect to the PRISMA by the Ethernet port or HUB and connect the light meter to the PC
USB ports.
3. Connect the PRISMA output to the monitor using an HDMI cable.

Page
8
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
WebOS Software Application Connections:
The Prisma uses a network connection for setup and advanced control including loading of LUTs
and assigning LUTs to the IR Remote. It can either be plugged into a standard 10/100 Ethernet
network, or can be connected directly to a computer with an Ethernet cable. The Prisma will
obtain a network address automatically using DHCP, or if there is no DHCP server available, it will
use a 169.x.x.x self-assigned address. This is compatible with the method most computers use to
assign network addresses and should be adequate for most users.
The Prisma announces its name on the network using both NetBIOS and DNS. This means that you
can access the Prisma from your computer's browser as http://prisma-xxxx.local on a
Mac/iPhone/iPad (or a windows computer with iTunes) or using http://prisma-xxxx on a Windows
computer.
When you connect your browser to the Prisma, you will be presented with its control panel. This
panel will allow you to select 3D Tables, adjust the PrismaVue parameters, and make other
changes to the Prisma.
Advanced Use of Prisma
There are several papers and articles on LUTs and calibration that you can find on the Murideo
web site. We'll start the discussion here by saying if you choose to optimize and maximize your
viewing experience to your environment and customize Prisma to your personal tastes that is
completely possible.
So, how do I create LUTs for each one of the buttons on the remote?
Let's start with the CalMAN example - CalMAN is advanced software that allows you to create a 3D
LUT!
A PC running CalMAN gets plugged into the Prisma via LAN and a light meter is connected to the
PC also for taking readings off the display. The Prisma has a built-in full 8-bit RGB triplet pattern
generator. As noted above - if possible plug the PC and the Prisma into a hub of some sort - makes
resolving the address a lot quicker. SpectraCal has a great article on creating 3D LUTs – see
Appendix A
The process once connected:
1. Quick method - put the TV in Cinema Mode and do a basic adjustment of black and white
level and go....
2. LUT creation - Use the Color Cube workflow in CalMAN - This will take you through a full
setup and calibration of the display including grayscale calibration, gamma, and front panel
controls.
3. Once you pick 1 or 2 above...time to get her done.

Page
9
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
4. It is important to note that CalMAN is creating the LUT and Prisma is the box where the
LUT gets stored and then is inserted in line between the source and the display.
5.
During creation of the LUT there are two main parts - measuring the display with your
colorimeter and then with those measurements creating a LUT file (.3dl) to be placed in the
Prisma. The Prisma is used by CalMAN as a generator during this phase of LUT creation.
The Steps Are:
1) CalMAN ColorCube Workflow
2) Connect to your Meter
3) Connect Prisma as the Generator – Prisma has built-in RGB triplet generator.
4) Connect SpectraCal Cube LUT as your Display
5) IMPORTANT NOTE: On the Generator Tab in CalMAN there are unique settings for the Prisma -
one very important setting is a small box call Bypass 3D LUT. The default for this setting is checked
- meaning the LUT in the Prisma is not in the signal path. When creating LUTs you must leave this
box checked - so you don't write a LUT on top of another LUT. When you want to see how good of
a LUT CalMAN created you would uncheck this box once the LUT file is loaded in the Prisma and
then run a saturation sweep in post calibration.
6) On the 3D LUT step in CalMAN pressing the Auto-Cal button will bring up the page below:
7) In the middle of the page is Cube Generator Output - This is where we set up the attributes for
the LUT as follows:
File Format = 3DL
Output Cube Size = 17 Points
Bit Depth = 12

Page
10
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
File Path = leave as default or name it - ex Jeff Movie LUT (note: file names limited to 48 characters
including the 4 character (.3dl) extension. Spaces are OK, but some special characters cause
problems (particularly '&')
Under the 3D LUT Setting you should refer to SpectraCals document on Appendix A
8) Click OK - this will start the process of measuring and finally writing the LUT - this can take from
about 5 minutes to hours depending on how many samples you take - theoretically - the more
data/samples - the better end result.
Note the file name of the LUT you just created.
9) Jump back into the Prisma via WebOS ex. http://prisma-xxxx.local/ to get the screen below:
Now click on Choose File and find the .3DL file you just created - if you didn't change the path it
will be under SpectraCal/CalMAN/LUT. You can also use a general search to find it. Then press
Upload Cube.
Now the LUT is, in the example above, assigned to the Movie Preset

Page
11
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
10) You are basically done now unless you want to create more LUTs for different modes/presets
or if you want to, run a post calibration saturation sweep to graph the result.
Note: If you are going to run a post LUT report - saturation sweeps - make sure to go back to the
Generator Tab and UN-CHECK the bypass LUT box. This will tell CalMAN to use the LUT that is
currently selected in the Prisma.
Results
Below you will find three screenshots – Before – Lightening LUT – and 2000 Read LUT. The results
are quite simply stunning!
Setup
Panasonic Plasma circa 2013 VT60 – calibrated grayscale – gamma 2.2 – CMS untouched. Black,
White, Color set correctly.
Source – DirecTV HD Genie – via Xbox 1
Processor – Murideo Prisma
STB Xbox PrismaPanasonic VT60
↑
Before LUT – been watching this TV in my home office for a few years and thought the picture
was pretty good. As you can see DeltaE 2000 is approaching 10 across the board.

Page
12
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
↑
Lightening LUT – This LUT took CalMAN less than 5 minutes to create and it is quite impressive –
note the average DE has dropped to below 5.
↑
2000 Reads LUT – This is the result after about an hour – I set CalMAN for a 2000 read
LUT. Not only is the graph above fantastic the picture is literally stunning.

Page
13
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Frequently Asked Questions
How do I control the Prisma?
Option 1 – Use the included remote IR remote control. You have access to stored LUTs and
PrismaVue adjustment.
Option 2 - The Prisma uses a network connection for setup and advanced control including loading
of LUTs and assigning LUTs to the IR Remote. It can either be plugged in to a standard 10/100
Ethernet network, or can be connected directly to a computer with an Ethernet cable. The Prisma
will obtain a network address automatically using DHCP, or if there is no DHCP server available, it
will use a 169.x.x.x self-assigned address. This is compatible with the method most computers use
to assign network addresses and should be adequate for most users.
The Prisma announces its name on the network using both NetBIOS and mDNS. This means that
you can access the Prisma from your computer's browser as http://prisma.local on a
Mac/iPhone/iPad (or a windows computer with iTunes) or using http://prisma on a Windows
computer.
When you connect your browser to the Prisma, you will be presented with its control panel. This
panel will allow you to select 3D Tables, adjust the PrismaVue parameters, and make other
changes to the Prisma.
How do I install my own 3D LUTs?
Open the Prisma WebOS, and select the "Cube LUT" panel. Use the file selection and upload to
copy the LUT file to the Prisma's internal storage. Once the table has been copied to the Prisma, it
can be selected with the Select Table control.

Page
14
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
What 3D LUT formats does the Prisma support?
The Prisma supports two different formats for 3D LUTs - the .3dl format and an internal binary
format. The 3dl format is stored in 12-bit precision and the pre-LUT is assumed to be a linear
identity. The internal binary representation is a compact format that can be used to save storage
space and provide faster load times.
How many LUTs can I store on the Prisma?
The Prisma has 1 megabyte of internal storage for data storage. A typical 17x17x17 .3dl is about
67kbytes, so the Prisma could store about 15 of these tables. The internal binary format is about
20kbytes, so there is room for about 50 of these tables.
How can I store a LUT in the binary format?
The easiest way is to load the .3dl table to the Prisma and then save it to a binary version, then
delete the .3dl. We are currently developing software that is able to read a .3dl and create the
binary version.
How does the PrismaVue work?
PrismaVue is an advanced implementation of unsharp masking or USM. Basically, there are two
steps to the process - for each pixel on the screen (frame), the first step calculates a blurred value
from the neighboring pixels. On Prisma, this is done with a 5x5 convolution filter for each Red,
Green, and Blue sub-pixel. The second step takes this blurred value and then subtracts some of it
from the original pixel. The Amount parameter controls how much is subtracted. The Threshold
parameter controls whether the original pixel is output, or if the blurred and subtracted pixel is
output.
Source image (top), sharpened image (middle), highly sharpened image (bottom).

Page
15
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
To use PrismaVue simply increase + or decrease – via the remote control and use the demo button
to see before and after result. Set to your personal taste. In the WebOS you can also set to
PrismaVue value numerically – 0 = no PrismaVue – higher + numbers = more PrismaVue
(sharpening) and a lower – number = less sharpening.
What is Prisma's video processing path?
The Prisma has two primary processing blocks - the Cube LUT is applied first, then the output of
the Cube goes to the PrismaVue.
The Cube can either be processed in linear space, or in the typical non-linear space. The control
for this is set in the Cube Table, so it can easily be enabled for some LUTs and disabled for others.
The Cube internally processes video in 18 bits per color component. This is to give enough bit-
depth for the linearization. The Cube coefficients are stored in 10-bit resolution and shifted to 18
bits during the processing.
The PrismaVue is processed in 10 bits, with the blur matrix coefficients stored in a 4.6 fixed point
format.
I thought video calibration was all about disabling this type of processing. What gives?
The true Videophile's goal is to set up their viewing room so that the picture they see is as close as
possible to the way the director intended. Unfortunately, there are many obstacles that get in the
way of achieving this goal. Even with the highest quality video equipment in a room that has been
meticulously set up - we are still at the mercy of how the content has been delivered. A blu-ray
disc that has been well mastered under the direct supervision of the director has the best chance
of realizing this goal.
Content today comes from many different sources, ranging from the high quality blu-rays, down to
cheaply mastered DVDs or even streamed off smart phones or the internet. The internet
streaming services are rapidly improving the quality of their distribution, but they still introduce

Page
16
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
compression artifacts. The Prisma can soften the image to reduce harsh compression artifacts, or
it can sharpen to bring back detail that has been lost in the compression process.
Overall, the Prisma's advanced implementation of PrismaVue sharpening and Cube table, when
applied properly, significantly enhance the overall viewing experience.
Is there a software API that I can use to control the Prisma?
Yes an API is available. All operations on the Prisma can be controlled through regular HTTP
requests and responses. The documentation on each request is available by request.
Is Murideo-Prisma supported by 3rd party software vendors?
Yes – SpectraCal - CalMAN provides full support in version 5.4 and greater. We can send you a PDF
or see Appendix A
Yes – Light Illusion – LightSpace – Use this link: http://www.lightillusion.com/prisma_manual.html
Yes – Argyle – Shareware – we are currently working on meter support and will post update on our
site as we develop and test this software – current meter support includes SpectraCal C6, X-Rite
Chroma V, Klein K-10 and X-Rite I1Pro2

Page
17
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
FCC Interference and Compliance Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution
To comply with the limits for an FCC Class B computing device, always use the shielded signal cord
supplied with this unit. The Federal Communications Commission warns that changes or
modifications of the unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995;
EN61000-3-3/1995,EN55024/1998, EN60950-1/2001)
Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic
environment, this product may cause radio interference in which case the user may be required to
take adequate measures.

Page
18
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
Warranty and Getting Help
General Warranty Terms
AVPro Global Holdings (DBA MURIDEO) offers a limited warranty for its MURIDEO products. Any
product first sold to you is guaranteed to be free from defects in both components and
workmanship under regular uses. The warranty period commences on the date the item ships.
Attention: Your invoice with the date of purchase, model number and serial number of the
product is your proof of the date of purchase. The International Limited Warranty is applicable and
shall be honored in every country where MURIDEO or its Authorized Service Providers offer
warranty service subject to the terms and conditions provided in this International Limited
Warranty Statement.
MURIDEO Products Warranty Period
The warranty terms for MURIDEO products are: Domestic & Asia EU & UK
MURIDEO – Fresco Six-G HDMI 2.0, 4K Test Pattern Generator 1 Year & 2 Year
MURIDEO – Prisma Networked Video Processor 1 Year & 2 Year
System Warranty
During the warranty period, the defective hardware of MURIDEO products will be either repaired
or replaced, with new or like new products, at the discretion of MURIDEO except in the cases listed
in the Limitation of Liability Clause of this document. This International Limited Warranty covers
the costs of service parts and labor required to restore your product to fully functional condition.
MURIDEO will, at its discretion, repair or replace any defective products or parts thereof covered
by this International Limited warranty with refurbished parts of the product that are equivalent to
new or like new products in both functionality and performance. A product or part that is repaired
or replaced under this International Limited Warranty shall be covered for the remainder of the
original warranty period applying to the product or part, or for 90-days, whichever expires last. All
exchanged parts and products under this International Limited Warranty will become the property
of MURIDEO.
Obtaining the Warranty Service
Warranty service or Returned Merchandise Authorization (RMA) under this International Limited
Warranty will be honored only if claims are made within the warranty period. For notifications to
MURIDEO or products outside the warranty period, the process will be the same, but charges may
apply. Contact details may be obtained on MURIDEO website http://avpro.r n
maportal.com/Customers are requested to perform the following actions before claiming
MURIDEO product as defective:
(a) Owner must notify MURIDEO, during the warranty period, in writing of alleged defect, and
allow MURIDEO a reasonable opportunity to inspect the allegedly defective product;

Page
19
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
(b) No Product may be returned without MURIDEO’s consent, The MURIDEO RMA# must
accompany all returns, and all returns must be delivered to MURIDEO within the warranty period;
(c) Owner may, then at its own expense, return the allegedly defective Product, freight pre-paid
and in the original packaging, accompanied by a brief statement explaining the alleged defect to
MURIDEO;
(d) If MURIDEO determines that any returned Product is not defective, or if MURIDEO determines
that the defect is not covered by the warranty, MURIDEO will return the Product to the Owner at
Owner’s expense, freight collect, and Owner agrees to pay MURIDEO’s reasonable cost of handling
and testing;
(e) Upon determining that a returned product is defective, to receive warranty service Owner will
need to present the invoice showing the original purchase transaction. If shipping the product,
Owner will need to package it carefully and send it, transportation prepaid by a traceable, insured
method, to the MURIDEO Service Center. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include the RMA #, your
name, return shipping address, email address and telephone number where you may be reached
during business hours, inside the shipping package with the unit. Any replacement unit will be
warranted under these Terms and Conditions for the remainder of the original warranty period or
ninety (90) days whichever is longer.
Refer to user manual enclosed within the product package and/or information on
http://www.murideo.com/ for important tips on how to operate and troubleshoot the product.
International Warranty
Warranty may be valid when a MURIDEO product is purchased in one country and transferred to
another country, without voiding the warranty. Please be advised that service availability and
response time may vary from country to country. Warranty is transferrable within the warranty
period.
MURIDEO is not responsible for any export and import control issues, handling fees, tariffs, import
duties, and all other related fees where owner is responsible for shipping its products. This
International Limited warranty does not affect your statutory rights.
Limitation of Liability
MURIDEO reserves the right to refuse warranty service of products under disputable conditions.
MURIDEO also holds the rights to declare final decision whether products are within warranty
conditions. The following actions and damages will result in voiding the limited warranty:
• Damage caused by act of nature, such as fire, flood, wind, earthquake, lightning, etc.
• Damage or incompatibility caused by failure to perform a proper installation or to provide an
appropriate operational environment for the product, including but not limited to unstable wired/
wireless network connection and phone lines, bad grounding, external electro-magnetic fields,
direct sunlight, high humidity and vibration.

Page
20
of
30
Call the AVPro Team at –North America 877-886-5112 International [phone]
• Damage caused by impact with other objects, dropping, falls, spilled liquids, or submersion in
liquids.
• Damage caused by unauthorized repair or disassembling of the product.
• Damage caused by any other abuse, misuse, mishandling, or misapplication.
• Damage caused by third party peripherals (including but not limited to visible damages on
motherboard or other electronic parts of the product such as burn spots after electric discharge,
melting, fusing, splitting, etc.)
• Any unauthorized software or modification of built-in software not approved by MURIDEO.
• The serial number of the product (or serial number stickers of its parts) has been modified,
removed, blurred or damaged.
• Defects caused by transportation, handling or customer abuse.
Disclaimer of Warranty
THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS
FOR APARTICULAR PURPOSE AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON MURIDEO’S
PART, AND ITNEITHER ASSUMES NOR AUTHORIZES ANY OTHER PARTY TO ASSUME FOR MURIDEO
ANY OTHERLIABILITIES. THE FOREGOING CONSTITUTES THE BUYER’S SOLE AND EXCLUSIVE
REMEDY FOR THEFURNISHING OF DEFECTIVE OR NONCONFORMING PRODUCTS AND MURIDEO
WILL NOT IN ANY EVENT BELIABLE FOR COST OF SUBSTITUTE OR REPLACEMENT, COST OF
FACILITIES OR SERVICE, DOWNTIMECOSTS, LOSS OF PROFITS, REVENUES OR GOODWILL, RELIANCE
DAMAGES, LOSS OF DATA, LOSS OFUSE IF OR DAMAGE TO ANY ASSOCIATED EQUIPMENT, OR ANY
OTHER INDIRECT, INCIDENTAL, SPECIAL,OR CONSEQUENTIAL DAMAGES BY REASON OF THE FACT
THAT SUCH PRODUCTS WILL HAVE BEENDETERMINED TO BE DEFECTIVE OR NONCONFORMING.
THE RIGHTS AND OBLIGATIONS OF THE PARTIES UNDER THIS AGREEMENT SHALL NOT BE
GOVERENED BY THE PROVISIONSOF THE 1980 U.S. CONVENTION ON CONTRACTS FOR THE
INTERNATIONAL SALE OF GOODS OR THE UNITED NATIONSCONVENTION ON THE LIMITATION
PERIOD IN THE INTERNATIONAL SALE OF GOODS, AS AMENDED (COLLECTIVELY,
THE“CONVENTIONS”); RATHER, THE RIGHTS AND OBLIGATIONS OF THE PARTIES SHALL BE
GOVERNED BY THE LAWS OF THE STATE of SOUTH DAKOTA, INCLUDING ITS PROVISIONS OF THE
UNIFORM COMMERCIAL CODE, AS APPLICABLE. FOR THE
AVOIDANCE OF DOUBT, THE CONVENTIONS ARE HEREBY EXCLUDED.
This Limited Warranty gives you specific legal rights. You may also have other rights that may vary
from state to state or from country to country. You are advised to consult applicable state or
country laws for full determination of your rights. Some jurisdictions do not allow the exclusion or
limitation of special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to everyone.