Mvix PLB-42 Installation instructions manual
Display Mounting Guide
Contents
1. Tilting Wall Mount
2. Ceiling Installation
3. Full Motion Wall Mount
Tilting Wall Mount
For 32” - 65” displays: Landscape or Portrait.
NOTE: Please read the instruction manual before you start installation and assembly.
866.310.4923 www.mvixusa.com
WARNING!
●Do not begin the installation until you have read and understood all the instructions and warnings
contained in this installation document. If you have any questions regarding any of these instructions or
warnings, please contact Mvix Technical Support.
●This mounting bracket was designed to be installed and used ONLY as specified in this manual.
Improper installation of this product may cause damage or serious injury.
●This product should only be installed by someone who has good mechanical sense, basic
building/construction experience, and who fully understands this manual.
●Make sure that the supporting surface will safely support the combined weight of the equipment and all
attached hardware and components.
●If mounting to a wooden joist, make sure that the mounting screws are anchored into the center of the
studs. The use of a stud finder is highly recommended.
●Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
●Tighten screws firmly, but do not over tighten. Overtightening can cause damage to the screws or
screw holes, greatly reducing their ability to hold the load.
●This product is intended for indoor use only. Using this product outdoors could lead to product failure
and personal injury.
Component Checklist
Important: Please inventory the package contents to ensure you have all the proper parts, as listed below. If
anything is missing or damaged, please contact Mvix Customer Service for a replacement.
For 32” displays:
866.310.4923 www.mvixusa.com
1a. For Wood Stud Wall Mounting
WARNING!
●Make sure that the mounting screws are anchored into the center of the studs. The use of a stud finder
is highly recommended.
●Installers are responsible for providing for any hardware needed for other types of mounting situations.
●Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
866.310.4923 www.mvixusa.com
2-2 For Recessed Back Back Screens or to Access A/V Inputs
*Tighten Screws but do not overtighten.
NOTE: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
●Position the adapter brackets as close as possible to the center of the TV.
●Screw the adapter brackets onto the TV.
866.310.4923 www.mvixusa.com
3. Hanging the TV onto the Wall Plate
Hook the TV over the top of the wall plate. Tighten safety screws on the display brackets with a proper
screwdriver.
Important: Make sure the TV is correctly hooked and the safety locking screws are locked safely before
releasing the TV.
866.310.4923 www.mvixusa.com
3. Adjustment
Use the tilt adjusting knob to adjust your TV to the desired angle.
Maintenance
●Check the the bracket is secure and safe to use at regular intervals (at least every three months)
●If you have any questions, please contact Mvix Technical Support for assistance.
866.310.4923 www.mvixusa.com
WARNING!
●Installer must verify that the ceiling will safely support the combined weight of all
attached equipment and hardware.
Use a qualified professional to properly install. Mvix is not liable for the improper use of installation of its products. Common hardware provided. Installers
are responsible to provide additional hardwares. The TV must not exceed 132 lbs, which is the maximum weight capacity of the bracket.
Wood Joists or Wood Beam Ceiling Installation
1. Locate the Wood joists
Using a “edge to edge” stud finder(commercially available), make marks at the edges of the joists. then mark
the centerline of the joists
2. Drill Pilot Holes
2-1. Hold the ceiling hanger so the holes line up with the stud center lines.
2-2. Drill pilot hole, this is a hole slightly smaller in diameter than the diameter of the big screws at each mark.
Concrete Ceiling Installation
1. Drill Mounting Holes
1-1. Hold the ceiling hanger against the ceiling where you want to
mount the screen.
1-2. Mark off holes to be used for securing the ceiling hanger and
place the ceiling hanger aside.
1-3. Using a masonry bit, drill holes at the spots marked in the
previous step.
866.310.4923 www.mvixusa.com
2. Install Anchors
Find the plastic concrete anchors (do not use it in wood joists ceiling). Place an anchor in each
hole. Tap each anchor flush with the ceiling using a hammer.
3. Mount Ceiling Hanger
Using the provided bolts and washers, tighten each bolt with an open ended socket wrench. Do
not use power drill and do not over tighten the bolts.
4. Assemble Ceiling Hanger and Mounting Plate
Adjust the length of the inner tube to a suitable position, and then insert a safety pin and screw down the knob.
Next, loosen the bolts, washers and locknuts to separate them. Using the bolts to get through the washer,
mounting plate, fixed frame, bolts, washers, and locknut in turn to fix the mounting plate with the fixed frame
firmly.
5. Attach Vertical Brackets to the Back of the TV
5-1. There are four mounting holes in the back of the TV, sometimes covered by plastic cap or screws. Use a
screwdriver to remove the caps or screws to expose the mounting holes. Check the TV manual if you cannot
find them.
5-2. Line up the two vertical brackets as shown. Attach each vertical bracket using screws, lock washers and
then washers as shown. Use screws that fit securely into your screen at least 3 full turns.
5-3. If the back of your screen does not lie flush with the screen arms, place washers between the arms and
screen back to fill the gap.
866.310.4923 www.mvixusa.com
6. Hang the Screen on the Mounting Plate
6-1. Two people, pick up the screen and hang the screen on the op and bottom edge of the mounting plate.
6-2. Slowly lower the screen so that it hangs on the Mounting Plate.
6-3. Move the screen slightly left or right so it is in the proper position on the mounting plate. 6-4. Tighten the
security bolts. This will prevent the screen from moving up on the mounting plate.
6-5. Verify that you cannot pull the bottom edge of the screen away from the wall.
866.310.4923 www.mvixusa.com
These instructions are for illustration purposes only. Mvix disclaims all liability for any special, direct, incidental or consequential damages, or any
damages whatsoever, without limitation, the loss of life or limb, or damages due to bodily or personal injury, which may arise or result from the
installation, or use of any of its products and parts. It is the user’s responsibility to inspect and verify the dimensions, specifications, and performance of
all products and parts as being appropriate for the use to which the user will put them prior to any actual installation and/or use of products and parts.
866.310.4923 www.mvixusa.com
This manual suits for next models
1
Table of contents
Popular Rack & Stand manuals by other brands
HAGOR
HAGOR PLD Single HD installation manual
TradeQuip
TradeQuip 1192T owner's manual
Total Control Products
Total Control Products RCKP214 Installaton guide
MetalMaster
MetalMaster SHST-1.2H Assembly and operating instructions
Safco
Safco Bamboo Costumer 4611 Assembly instructions
Stell
Stell SHO 5000 manual
