MyPressi Twist User manual
USER
GUIDE
WARNING: Read this manual carefully before use. Keep
this manual for future reference. Keep away from chil-
dren. If you have questions about the assembly, operation,
servicing or repair of this device, please call mypressi at
1-408-770-8500 or email info@mypressi.com. And be
prepared to enjoy some seriously good espresso.
WARNING: Read this manual carefully before use. Keep
this manual for future reference. Keep away from children.
If you have questions about the assembly, operation,
servicing or repair of this device, please call mypressi
at 1-408-770-8500 or email info@mypressi.com.
And remember: life is too short for bad coffee.
2 3
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
INTRODUCTION
WARNING
The mypressi® TWISTTM is a pressurized system. All parts have been extensively tested during manufac-
ture, however improper use can put you and others at risk. The TWIST is intended for household use
only. NEVER use the TWIST in any manner contrary to these directions. NOT FOR USE by children. NEVER
consume liquid directly from the TWIST as contents may be hot. ALWAYS use the TWIST on a flat, stable
surface. NEVER place the TWIST near an open flame, a hot gas or electric burner, or on or in a gas or
electric oven, an electric hot plate, a microwave or dishwasher. ONLY USE clean, hot water in the TWIST.
Do not use any other fluid. NEVER heat the water directly in the water bowl. Water must be heated by an
external heating source such as a kettle and then poured into the bowl. DO NOT USE any accessories not
recommended by the manufacturer, as this may cause injury. DO NOT USE the TWIST if it is showing any
sign of breakdown or malfunction. Place the TWIST on a flat stable surface before pouring water into the
water bowl. DO NOT unscrew the end-cap while the TWIST is under pressure (with a full or partially full
cartridge in the handle). If you must remove the cartridge while it is still full, remove the water bowl, then
release the pressure in the TWIST by holding the trigger until all the gas has been expelled. DO NOT use
the TWIST for other than its intended use.
EXERCISE CAUTION when inserting or removing the pressure cartridge. DO NOT remove or attempt to
remove the water bowl or water bowl lid while operating. After releasing trigger wait at least 20 seconds
before removing the water bowl or lid. Never force open the water bowl or lid. The water bowl or lid may
feel tight where there is residual pressure. Always wait for all pressure to dissipate before opening. This
may take up to 10 minutes. ONLY use 8gm 600 psi N2O cartridges or CO2 cartridges.
© 2009-2010 Espressi, Inc. All rights reserved. Under the copyright laws, this manual may not be copied
in whole or in part without the written consent of Espressi, Inc. mypressi and TWIST are trademarks of
Espressi, Inc in the US and other countries. Every effort has been made to ensure that the information in
this manual is accurate. Espressi, Inc is not responsible for printing or clerical errors.
Congratulations on your new mypressi®TWISTTM, the revolutionary,
handheld espresso maker that’s perfect for the home, office and just
about everywhere else!
This User Guide will help you get the most from your TWIST, but before we begin, what exactly is espresso?
Espresso is a concentrated coffee extraction utilizing heat (197-204F) and pressure (9 bars of atmospheric
pressure or roughly 135psi). It should be smooth with an intense aroma and velvety crema. It can be
consumed as a shot, and also used as the base for many other drinks and desserts.
The TWIST develops the operating pressure using food-safe, inert gas in two forms: Nitrous Oxide (N2O)
and Carbon Dioxide (CO2). Each 8gm charger, or gas cartridge, delivers sufficient pressure for up to 4
double shots of espresso or 8 singles. The chargers are based upon a safe and proven technology that
has been widely used in other household devices such as whipped cream dispensers and soda makers for
the last 80 years. The chargers are readily available from a wide variety of stores and online retailers. You
can also find the mypressi-brand of chargers at www.mypressi.com. Each cartridge is made from 100%
pure steel and is fully recyclable.
Espresso is made with 18-21 grams of fresh ground coffee and roughly 2oz (60ml) of water, and therefore
has a high coffee to water ratio, unlike any other coffee extraction. Your TWIST includes several baskets
that will help you achieve the best results possible during this process: a double basket (21g) for fresh
ground coffee; a pressurized basket for pre-ground coffee or coffee that is coarser then a traditional
espresso grind; and, an ESE-compatible pod basket for single serving (7g) pods. If you prefer pods, there
is also a special shower head to ensure proper fit for an optimum extraction.
We have poured thought, care and creativity into the TWIST so that it will serve you well. There really is no
other machine that offers you excellent results while complying with such a small environmental footprint
and an über-stylish look and feel! We trust it will deliver the ultimate espresso experience, convenience,
portability and quality for many years to come.
Finally, please remember that the TWIST is a highly pressurized device. Always use with safety and care
and please only use in accordance with the instructions contained in this manual.
UG1007A-PRNA
Espressi, Inc
2580 N. 1st Street, Suite 130
San Jose, CA 95131 USA
Ph: +1 408 770 8501
4 5
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
BEFORE YOU BEGIN
Rinse all components of the TWIST including the water bowl, showerheads, baskets,
lid and main handle in clean hot water. Place your thumb over the small o-ring on
the handle to prevent it inadvertently washing away. Thoroughly remove all soaps if
applicable. You may also remove the caution label regarding the small o-ring, and if
you should ever notice that o-ring missing, or you think your TWIST is not pressur-
izing, just replace it from the collection of spare o-rings provided.
DO NOT place any of the TWIST’s components in a dishwasher as the heat may
damage the materials or cause discoloration. For more information, turn to “Care &
Maintenance.”
The TWIST will only work if there is a compressed gas cartridge installed in the
handle. Make sure that you have done so before attempting to produce espresso.
FOR BEST RESULTS:
s5SEFRESHROASTEDSPECIALTYCOFFEEANDlLTEREDWATER
s)FPOSSIBLEGRINDCOFFEEFRESHWITHAGOODQUALITYBURRGRINDERh%SPRESSOvGRINDISMUCHlNERTHAN
THATOFPREPACKAGEDGROUNDCOFFEE5SETHEhCOARSEvBASKETIFYOUREXTRACTIONISTOOFAST
s%NSUREPROPERDOSEWITHAGRAMSCALE
s4AMPTHECOFFEEWITHAROUNDLBSOFPRESSURE
s2EMOVETHELOWERBOWLANDUTILIZETHE47)34ASABOTTOMLESSPORTAlLTER
exposing the base of the basket.
s0REHEATTHEWATERBOWLANDYOURCUPWITHVERYHOTORBOILINGWATERWAITSECONDSANDEMPTY
s0REHEATTHELOWERBOWLBYPOURINGSOMEHOTWATERTHROUGHWHILETHEBASKETISINTHEHANDLE
s0OURAFEWOUNCESOFPREHEATEDWATEROVERTHESTANDARDBASKETWHILEITISINTHEHANDLEWAIT
seconds before removing the basket).
s%VERYTHINGSHINYORINCONTACTWITHWATERISHOTSOBECAREFUL
INSERTING A CHARGER
Unscrew the end cap from the TWIST’s handle, the follow the steps as pictured below:
a. Place the large end of the gas charger into the end cap.
b. Screw both back into the handle until is is completely flush with the body.
c. The metal bands on the end cap and handle should match up.
TIP: Each charger will make up
to four double or eight single
shots. Track your double shots
using the shot-counter on the
water bowl. (We always prefer
double shots to singles, so the
shot counter counts doubles.)
A B
C
6 7
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
PARTS & ACCESSORIES
pod basket
(single)
1 Water Bowl Lid
2 Water Bowl
3 Standard Showerhead
4 Standard Basket
5 Basket Holder
6 Lower Bowl
7 Spouts
8 Trigger
9 Handle
10 Gas Cartridge
11 End Cap
12 Tamper
13 Coaster and
Tamping Mat
14 Water Bowl O-Ring
15 Upper/Lower Show-
erhead O-Rings
16 Small O-Ring
standard showerhead
standard showerheadpod showerhead
standard basket coarse basket
use with 18-21g of
fresh espresso (very fine)
ground coffee
You can also tamp 8-10g of
coffee into the pod basket
while using the standard
showerhead to pull a
single shot.
Specifically designed for
use with single serving
(7g) ESE compatible pods.
Use only with the pod
showerhead.
use with pre-ground coffees or if
your grinder is unable to grind fine
enough for traditional espresso
1
2
12
14
13
3
4
5
6
7
8
16
9 10 11
15
8 9
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
QUICK START GUIDE
Fill the basket with ground
coffee (18-21g). Level off
and tamp firmly.
Place the basket in the holder
and place the empty water bowl
on top, locking it into place.
1 2
Position spouts over one or two
cups and press the trigger until
you have the desired volume.
Carefully fill the water bowl with
hot water (197-204 F). Place
and lock water bowl cap firmly.
CAUTION: Pressure and high temperatures are used in
the preparation of espresso. Wait at least 20 seconds after
releasing the trigger before untwisting the water bowl from the
handle. There may be a release of excess pressure.
Be patient and very particular. It is quite common to spend a few minutes prepping
for a good extraction. Sometimes with the first few espressos from any machine,
I’ll dump the shots until I get the results I’m craving. For more tips and problem
solving, join me online at www.mypressi.com. Cheers!
Sarah Dooley
Director of Education, mypressi
3 4
When cleaning the TWIST place your thumb over the
small o-ring on the handle to prevent it inadvertently
washing away.
10 11
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
USING THE TWIST
STEP 1:
CHOOSE A BASKET
Remove the water bowl from the top of the TWIST by rotating
it counterclockwise. The bowl will be snug at first, loosening
up a little with use. Always use the proper basket for the intend-
ed use. If you are using red espresso®, use the coarse basket
as the particles are larger than a standard espresso grind.
CHOOSE A SHOWERHEAD
The TWIST comes with two showerheads: One for ground
coffee (A) and one for Pods (B). To ensure the showerhead is
securely in place underneath the water bowl, press the show-
erhead into the water bowl slots. The showerhead will snugly
seal into place with the water holes facing down, just like in
your shower at home.
STEP 2:
Standard Basket
Coarse Basket Pod Basket
NOTE: The two showerheads have been optimized to work most effectively
when used with the proper baskets. (see pg 7)
A B
12 13
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
USING THE TWIST
LOAD THE BASKET
Place the standard or coarse basket on a flat, stable surface.
You can also use the included coaster as a tamping mat.
a.$OSEWITHGOFhESPRESSOvGRINDCOFFEE5SEAGRAM
scale for the highest accuracy.)
b. Tamp the coffee firmly and flat, using around 30lbs
of pressure.
c. Brush excess coffee away from the rim to ensure
a water tight seal.
d. Place the basket in the basket holder.
e. Place the water bowl on the handle and turn to align both
the marks and securely lock the units.
WHEN USING A POD
a. Replace the standard shower head by lifting up on the tab with your fingers.
b.)NSERTTHESHOWERHEADMARKEDh0/$vINTOTHEBOTTOMOFTHEWATERBOWLAND
press down firmly. If the water bowl does not lock into the handle you may
need to re-seat the POD showerhead ensuring it is even, tight fit.
c. Place the basket marked POD into the basket holder on the main handle.
It is normal on some pods for the pod’s paper tab to hang out over the rim.
d. Place the water bowl on the handle and turn to align both the marks and
securely lock the bowl onto the handle.
STEP 3:
A
B
C D
CAUTION: Only use single serve (7g) ESE pods in your TWIST.
For best results
always use fresh
ground coffee.
14 15
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
USING THE TWIST
FILL WITH HOT WATER
Remove the lid from the water bowl. Carefully pour in hot wa-
ter. For a shorter shot or when using a pod fill the water to the
bottom of the water level tab (approximately 1 oz or 30ml). For
a longer shot of espresso, fill the water to the upper line inside
the water bowl (2 oz or 60 ml). Secure the lid by rotating it
slightly to the left, then to the right until firmly locked in place.
STEP 4:
PULL A SHOT
To ensure an even extraction, practice having a steady,
balanced hand. Preheat your cups to retain the heat of the
shot. Hold the spouts over one cup for a double or two cups
for single shots. You can also remove the lower bowl exposing
a naked basket for a bottomless extraction. Pull the trigger, en-
gage for 20-30 seconds or until the pre-portioned water stops
flowing. There will be a soft hissing release of excess pressure
from the water bowl when you release the trigger.
STEP 5:
Spouted Naked
NOTE: Use the shot indicator marks on top of the water
bowl to remember how many times you have used a
single cartridge by aligning the water-bowl lid with the
last shot number.
NOTE: Wait at least 20 seconds before removing the water bowl from the handle, allowing the chamber
to depressurize. If the water bowl requires more force to remove then it did to put on, there may still
latent pressure remaining in the coffee basket.
For best results
use water just off
the boil
16 17
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
USING THE TWIST
CLEANING UP
The Twist is made from the highest quality food safe materials.
With proper care and cleaning it will serve you well for many
years to come.
Now that you have made your shot it’s time to do a quick but
thorough clean up. Unscrew the waterbowl cap and dump any
leftover hot water, then remove the waterbowl. Lift the basket
out of the basket holder, empty the grounds into your compost
bin, and rinse with warm water. Place your finger over the
small o-ring in the handle (part #16) so you don’t lose it during
rinsing. Rinse the entire basket holder and lower bowl in water,
washing away coffee grounds and residue.
You’re now ready to make more coffee.
STEP 6:
Clean the standard showerheadwhenever you
notice the waterbowl leaking a drip or two when filled with water. This is probably
due to the rubber disc having coffee grounds trapped underneath. Gently pry off the
o-ring on the underside or tap plastic part of the assembly against a hard surface
until the o-ring falls out. The metal piece should easily seaparate from the assembly
so you can clean around and under the rubber disc. Reassemble after cleaning.
Rubber disc
Showerhead
O-Ring
18 19
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
QUESTIONSFREQUENTLY ASKED
Q: The water bowl is not easy to remove.
A: In rare cases the small hole in the middle of the rubber valve inside the showerhead may have
become blocked with coffee particles, preventing a rapid equalization of pressure. Give the TWIST
sufficient time to release all pressure (sometimes as much as 5-10 minutes or more) and then
thoroughly clean the showerhead and rubber valve.
Q: The water bowl lid has become difficult to open or close.
A: Apply a small amount of food safe lubrication to the gasket on top of the water bowl. Wipe away any
extra lube to keep the area clean.
Q: An o-ring is not sealing the way it used to.
A: Replace the o-ring using one of the spares included with the TWIST. If you need more, send an email
Q: Water leaks through the water bowl when I fill it with hot water.
A: Time to do a deep clean as shown on page 17. Remove the showerhead from the water bowl and
angle a small, flat tool under the o-ring (part #15-lower). Carefully pry the o-ring loose. The show-
erhead screen should fall out. Rinse this with warm water and soap. Gently clean under the rubber
valve and all other using soap and water. Thoroughly rinse and reassemble.
Q: The extraction seems fast and results in weak coffee. The coffee sometimes even overflows from the
top of the bowl. What’s happening?
A: Usually this is caused by coffee that is too coarse. The freshness of the coffee and the humidity in the
air can also effect the rate of flow. Here are some troubleshooting tips:
- Use a finer grind of coffee. Make adjustments toward the finer settings on your grinder. We recom-
mend using a high quality burr grinder. Blade grinders cannot grind sufficiently fine. They also heat
up the coffee in the grinding process, creating large variances in the flow rate of your espresso.
- If you are having problems getting a fine enough grind, try using the coarse basket. If you rub a fine
espresso grind between your fingers it will feel like flour mixed with a little salt.
Q: The extraction seems too slow, somewhat drippy and doesn’t provide a steady pour. It may even taste
salty.
A: This is a slow extraction and it may be caused by several factors:
- You may have dosed in too much coffee.
- The grind setting may be too fine requiring a coarser grind of coffee to allow water flow.
- The cartridge may be near or at the end of its pressure. (Try the shot counter feature!)
- In rare cases, tamp pressure will change the flow rate. Be careful you are not tamping too hard. Use
a bathroom scale and a tamper to test how hard you are pushing down on the coffee bed.
Q: When I use pods to make a cup of espresso the water shoots through very fast and the espresso is
blond and very watery. What am I doing wrong?
A: You may be using the standard basket and standard showerhead. It is important that you use both
the pod basket and pod shower head in order to extract the coffee properly from a pod.
Q: When I use pods the espresso still comes out watery?
A: You may be pre-portioning too much water in the water bowl. Fill the water to the
lower fill mark in the bowl when using pods.
Q: How do I know if there is sufficient gas left in the cartridge to make another shot of espresso?
A: You can make 4 double shots or 8 single shots of espresso from one cartridge. If you have lost
track, remove the water bowl and while holding the TWIST away from you, give the trigger a quick
squeeze to see if there is any pressure in the system. Gas will come out of the small o-ring on top of
the handle and may be followed by a small amount of water spray. If you have pulled sufficient shots
already, you will probably notice just a small amount of gas followed by the cartridge running out of
pressure. If you get a good blast of gas coming from the small o-ring then you can probably make at
least one more shot.
Q: Why does water occasionally leak out near the trigger during use?
A: This is due to condensation and is normal. Just wipe off the water and continue.
Q: Sometimes the espresso is not very hot when I make a shot. What can I do to make it hotter?
A: There are a number of things you can do to get consistent and proper water temperatures:
- Pour hot water directly from your boiling kettle into the water bowl.
- Preheat the cup or shot glass before use, but don’t fill to the top or you risk burning your lips. You
can also run some of that hot water through the basket and spouts to ensure all components are
PREHEATEDORMAKEAhNAKEDvSHOTWITHTHESPOUTSREMOVEDFOREVENHOTTERRESULTS
- Preheat the water bowl in a similar fashion, fill it with boiling kettle water and dump the water after
15-20 seconds. Repeat if required. Cooler shots can taste a little sour, so the more heat you bring
in at the start, (ranging from 197-204F at the point of extraction) the better opportunity you have for
great espresso. If you need further help, call us on +1 408 770 8500 and talk to our support line.
20 21
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
RECIPESESPRESSO
ESPRESSO RISTRETTO
Use 18-21g of finely ground coffee, and approximately 1oz of water. Preheat the
water bowl twice, about 15 seconds each time, for best results. Use a good grinder
and excellent beans. Remove the lower bowl for best results.
ESPRESSO MACCHIATO
Top your espresso with 1 to 2 tablespoons of foamed milk. Make it in a standard
espresso cup, usually called a demitasse. (The best espresso cups are in the
demitasse style, thick to hold the heat, with small handle. They should always be
preheated with hot water. Easiest way is to do that when you preheat the TWIST.)
ESPRESSO CON PANNA
Top a single or double espresso shot with whipped cream.
ESPRESSO ROMANO
Top a single shot of espresso with a small curl of lemon peel. Leave the end of the
curl hanging out of the cup for that sophisticated cafe style.
DRY CAPPUCCINO
Top one part espresso with 3 to 4 parts of foam. Drink the espresso through the
foam. Don’t forget to wipe your upper lip. :)
WET CAPPUCCINO
Top 1 part espresso with 1 part steamed milk and 1 part foam.
CAFÉ LATTÉ
Top a single shot of espresso with 3 to 4 parts of steamed milk, holding back the
foam. If you add foam, you have a wet cappuccino.
AMERICANO
Fill a cup with hot water from the kettle, then extract the espresso on top. You’ll get
a delicious black coffee with a topping of crema. And there’s nothing wrong with
adding a little milk, cream or sugar to suit your taste.
BLACK EYE
Take a cup of drip coffee and add 1 to 2 shots of espresso. And wake up!
MOCHA CAPPUCCINO
Dissolve cocoa or chocolate syrup into steams milk and pour over the top of 1 to 2
shots of espresso.
ESPRESSO DOPPIO
Double-up your standard espresso. You’ll probably need something larger than a
demitasse.
ICED MOCHA ESPRESSO
Mix your espresso with 2-3 tablespoons of cocoa, 1/2 teaspoon of vanilla extract
and a cup of cold milk. Pour over ice and optionally top with whipped cream.
SPICED LATTÉ
Just like a regular latte but spiced up with a little honey, vanilla extract, cinnamon
and nutmeg. Not too much that it overpowers the coffee.
HEALTHY FRAPPÉ
Mix 3oz of chilled espresso with 3/4 cup of non-fat yogurt, 1/2 cup of ice cubes
and sweetener to taste. Place all ingredients into a blender and blend until smooth.
If you’re not calorie counting, substitue ice cream for the yogurt.
22 23
mypressi®TWISTTM user guide mypressi®TWISTTM user guide
GLOSSARY GLOSSARY
Basket:
A container designed to hold ground coffee or
pods for espresso extraction.
Blend:
A combination of different coffees varying in
roast, origin, species and/or varietal.
Blonding:
The usual golden brown of a good espresso
extraction can quickly turn blond towards the
end of the shot. The blond extraction typically
adds unwanted flavor characteristics ruining
an otherwise good cup. The extraction should
always be stopped at the point it shows the first
sign of turning blond. If that point is too early,
you may have an under extraction.
Channeling:
We can’t comment on other meanings, but
in espresso it means the water has forced its
way through uneven areas of the coffee puck,
resulting in an under extraction. Channeling
can be corrected by using the right setting for
the espresso grind, by distributing the ground
coffee carefully and evenly into the basket, and
by tamping down evenly with the appropriate
pressure.
CO2:
Carbon Dioxide. A colorless, odorless, and
non-flammable gas. It is naturally present in air
and is absorbed by plants in photosynthesis.
CO2 can lend a sour flavor to certain beverages
but has no impact on the flavor or aroma of
espresso made with the TWIST.
Crema:
An emulsification of fine particles of insoluble
solids and oils contained in millions of tiny
bubbles of water saturated with CO2. The
amount of crema extracted decreases as
the coffee gets older, the grind oxidizes and
becomes stale, or it is ground more coarse.
The coarser the coffee, the less crema will be
extracted. Crema isn’t necessarily the point to
espresso, and it may even be scooped off prior
to consumption, however the way it forms is al-
ways an excellent diagnostic tool for assessing
the quality of the extraction. Then again, so is
drinking what’s in the cup.
ESE Pods:
An Easy Serving Espresso Pod, or E.S.E. pod,
is a small packed disc of ground coffee with a
paper filter covering, generally 44-45mm wide.
The pod basket included is for use with 7g
single ESE pods and not 14g double ESE pods.
Espresso:
A type of extraction combining heat, coffee and
water to create a condensed syrupy liquid.
mypressi:
We make the TWIST, invented by an Australian
and designed in California. Enjoy responsibly.
N2O:
Nitrous Oxide. A colorless, non-flammable gas
with a slightly sweet odor and taste. It is also
KNOWNAShLAUGHINGGASv./HASNOIMPACT
on the flavor or aroma of espresso made with
the TWIST.
O-Ring:
A rubber gasket used to create water-tight and
air-tight seals to preserve pressure.
Over Extraction:
Occurs under the following conditions: the
espresso comes out as too concentrated an
extraction that may even taste salty and bitter;
the espresso is very dark with little crema;
it extracts too slowly for the desired volume
and time, dripping instead of flowing from the
basket; or the extraction is allowed to continue
too long, drawing out unwanted flavors. Over
extractions can usually be corrected by increas-
ing the coarseness of the grind.
Pressurized Basket:
A special, multi-layered basket intended for use
with coarser ground coffee and red espresso®.
The TWIST’s pressurized basket can be identi-
fied by the word COARSE.
red espresso®:
A South Africa based company that specializes
in rooibos tea prepared to be brewed like cof-
fee. It’s awesome in the TWIST. No kidding.
mypressi Origins:
Our donation program giving TWISTs to coffee
farmers to help them grow a better, tastier crop.
You can help as well by visiting
www.mypressi.com/origins.
Specialty Coffee:
Essentially the highest grade of coffee available
on the market.
Tamper:
A tool used by professional baristas to com-
press the bed of coffee in a basket for even
extraction. A good tamper is quite weighty. If
you want to step up from the platic tamper
included with the TWIST, look for a good 53mm
tamper. It can make a noticeable difference to
the extraction.
Tiger Striping:
A good espresso extraction shows its nature
by a combination of golden and dark brown
stripes that form under the espresso basket
and turn into spots or flecks in the cup, visible
on top of the crema. The darker stripes and
spots are formed from the oils and caramelized
sugars present in the roasted bean.
Under Extraction:
Occurs under the following conditions: the
espresso comes out under-concentrated,
tasting weak or sour; it extracts too quickly
for the desired volume and time; the espresso
is blond and pours rapidly from the basket in
multiple streams rather than 1 or 2 steady
streams; there’s a lot of channeling during the
extraction.
24 mypressi®TWISTTM user guide
WARRANTY
United States Limited Warranty Information
ONE YEAR LIMITED WARRANTY
Espressi, Inc warrants the TWIST against defects that are due to faulty materials or
workmanship for a period of 12 months from the date of purchase unless otherwise
required by law. Except as otherwise required by law, this warranty does not ap-
ply to retailers or other commercial purchasers or owners. This warranty does not
cover damage resulting from improper use, abuse, neglect, commercial use, or any
other use of this appliance not found in this printed User Guide. Tampering with
the machine or removing the plastic covers from the handle will void the warranty.
There is no warranty for filter baskets or o-rings. Espressi expressly disclaims all
responsibility for incidental or consequential damages caused by use of this ap-
pliance. Some states do not allow for the exclusion or limitation of consequential
damages or losses, so the foregoing limitation or exclusion may not apply to you.
ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO THIS APPLI-
ANCE IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY PERIOD. Some states
do not allow disclaimer of implied warranties, so the foregoing may not apply
to you.
If your mypressi TWIST fails within one year please email support@mypressi.
com, call +1 408 770 8500 and select “Returns and Exchanges”, or contact your
original place of purchase.
International Warranty Information
Go to www.mypressi.com/international, contact your original place of purchase
or your local distributor.
Other manuals for Twist
1
Table of contents
Other MyPressi Coffee Maker manuals
