NAC Image Technology Memrecam Q1v User manual

NOV 2014
Model ST-822
Introduction
Preparations
Basic
Operations
Spec
1
1
High Speed Digital Camera System
800375-0A
User's Manual

Read before Use
Information to the User
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
CE marking
This product with the CE marking complies with the EMC Directive 2004/108/EC and the Low
Voltage Directive 2006/95/EC.
1
(00375)

2
(00375)

Features of This Unit
The MEMRECAM Q1m/Q1v is a handheld high speed digital camera capable of high speed filming in
a variety of environments.
High Speed
・High Resolution ・High Sensitivity Image Sensor
Equipped with a highly sensitive CMOS sensor for color or black and white to enable high speed operation at
high resolutions.
The Q1m is capable of filming a maximum of 2,000 frames per second at
1280 × 1024 pixels, and a maximum
of 87,000 frames per second by reducing the horizontal and vertical pixels filmed. The sensitivity is ISO
1,000 for color and ISO 6,400 for black and wh
ite.
The Q1v is capable of filming a maximum of 8,000 frames per second at
640 × 480 pixels, and a maximum of
87,000 frames per second by reducing the horizontal and vertical pixels filmed. The sensitivity is ISO 8,000
for color and ISO 50,000 for black and white.
Onboard Memory
Equipped with a memory with a maximum of
8GB. (Memory may vary according to model.)
With the Q1m
8GB／1000pps／1280 × 1024／
8 bit recording model, high speed filming at a high resolution
is possible for as long as 6 seconds.
Superior Performance
High speed photography requiring advanced techniques can be easily performed.
Perform continuous recording to the semiconductor memory or via recording trigger input with confidence
that images will not be accidentally lost.
Flexible Image Playback
Slow motion playback of recorded images or repeated playback in a specified range is possible.
Detailed image analysis can be conducted with on a PC.
3
(00375)

High
-Speed Network Transfer
Recorded images can be digitally saved to a PC through the network, including the data settings during
recording and the trigger timing.
1000BASE-T／100BASE-TX
internet is used for high speed transfer even
for video data with high resolution/long recordings.
Memory Backup
Protects against losing recorded images during unexpected power loss with the memory backup function of
an internal battery.
Various External Interfaces
Connect Q
-CAM cables to use a wide variety of external input/output interfaces, including 1000BASE-T
／
100BASE
-TX
internet, recording start signal input, discrete status signal input/output, exposure pulse
signal output and recording trigger signal input. System corresponds to a wide range of recording conditions
for individual cameras.
The operating methods for the MEMRECAM Q1m and Q1v are basically identical. This guide
focuses the descriptions on the Q1m. Further explanations for items requiring Q1v
descriptions are provided for each model
4
(00375)

Trademarks
MEMRECAM is a trademark of NAC Image Technology.
Microsoft Windows is a registered trademark of Microsoft Corporation USA.
Other company names and product names noted here are trademarks or registered trademarks of
those companies.
Reproduction or duplication of any or all of this document without the express written consent of
NAC Image Technology is strictly prohibited.
The contents of this document may change without notice.
Copyright (C) 2014 NAC Image Technology
The copyright for this manual belongs to NAC Image Technology.
5
(00375)

Safety Precautions
Safety Precautions
Be sure to follow these safety items to avoid damage or bodily injury.
■Distinctions between the levels of bodily injury and
damage
The distinctions between the levels of bodily injury and damage occurring from improper use are described
below.
Extreme danger that may result in death or serious injury.
Potential danger that may result in death or serious injury.
Potential danger that may result in minor injury or damage to the device.
■Warning Symbols
Descriptions are provided for the following warning symbols.
Prohibited item
Mandatory item.
6
(00375)

Safety Precautions
Using the AC Adapter
●Do not use the Q1m/Q1v dedicated AC adapter on anything other than that specified.
(Malfunction or fire may occur.)
7
(00375)

Safety Precautions
Using the main camera unit
●Do not disassemble or alter
(
Do not loosen screws on the main camera unit or open the cover even if the camera
malfunctions.)
⇒Contact the store where purchased for inspection ・maintenance ・repair.
●Do not use in locations with smoke or flammable or corrosive gases, or strong magnetic fields
(Malfunction, injury or fire may occur.)
⇒Do not use in dirty, dusty or humid locations.
●If there is a malfunction, unplug the cables connected to the camera and the power plug for
the AC adapter
(
If water or other foreign objects get inside, if the exterior breaks due to being dropped, if
the camera becomes hotter than normal, or if smoke, odors or noises are emitted. The camera
becomes warmer during operation so this is not a malfunction.)
⇒Contact the store where purchased or our service center.
Using the cables
●Do not unplug the cable with the power on.
●Do not put foreign articles such as metal, trash or water inside the connector.
(Malfunction or
electrical shock may occur if the cable is connected or removed with the power
on.)
⇒Unplug the cable only after turning off the power.
●Do not touch the plug or connector with wet hands.
(Malfunction, electrical shock or fire may occur.)
Confirm the input power
●Check the input power before connecting.
During AC adapter use：AC100～240V/47～63Hz
During DC power connection：DC20～32V
(Malfunction, electrical shock or fire may occur if connected to the wrong power supply.)
8
(00375)

Safety Precautions
Using the AC Adapter
●Do not disassemble or alter
(Do not loosen screws on the AC adapter or open the cover even if the AC adapter
malfunctions.)
⇒Contact the store where purchased for inspection ・maintenance ・repair.
●Do not use in locations with smoke or flammable or corrosive gases, or strong magnetic fields
(Malfunction, injury or fire may occur.)
⇒Do not use in dirty, dusty or humid locations.
●Do not subject to strong vibration or impact
(The AC
adapter does not have vibration or impact resistance properties based on actual impact
testing. If subject to strong impact or vibration, malfunction or injury may occur.)
⇒Contact the store where purchased or our service center if using in such environments.
●If there is a malfunction, unplug the power cord.
If water or other foreign objects get inside, if the exterior breaks due to being dropped, if the
camera becomes hotter than normal, or if smoke, odors or noises are emitted. The camera
becomes warmer during operation so this is not a malfunction.)
⇒Contact the store where purchased or our service center.
9
(00375)

Safety Precautions
Using the main camera unit
●Do not interfere with the release of heat from the camera
(The Q1m/Q1v
has a fan that cools the camera. Do not block the intake ports or vents.
Additionally, do not place in narrow locations where there is no air circulation, or on carpet or
bedding.
If heat builds up inside, malfunction or fire may occur.)
●
Do not put fingers or objects in the lens mount
(
The sensor can be seen if the lens or cap on the lens mount of the camera is removed. If
fingers or items are placed inside, the sensor may become scratched or dirty so the image
quality may be adversely affected.)
●
Do not place heavy items on this device.
(
If tipped over or dropped, the exterior may be damaged, which may cause bodily injury.
Additionally, if heavy items are placed on it, the exterior may be deformed, causing the interior
components to be damaged and malfunction. )
●Check the ambient temperature of the location where used and stored.
Use temperature range：1～40℃, humidity 30～80%RH, no condensation
Storage temperature range：1～60℃, humidity 20～80%RH, no condensation
Using the Battery
●
Do not leave the camera in locations with high temperatures, such as in closed vehicles, near
flame, or on top of stoves
( The Q1m/Q1v has a memory backup battery which may cause the battery to leak
or reduce the
battery performance or life.)
Handling while moving or transporting
●
Use the dedicated storage case for moving or transporting this device
(
To protect the camera from malfunction, use the optional dedicated storage case for
transport.)
10
(00375)

Safety Precautions
Using the AC Adapter
●Use environment
Avoid using in locations with smoke or corrosive gases, or strong magnetic fields
Do not leave in direct sunlight or locations subject to rain or salt water.
Do not use in dirty, dusty or humid locations.
●Check the input power
(The AC adapter is AC100～240V, 47～
63Hz so check the power voltage, frequency and polarity
before connecting to a power source.)
●Check the ambient temperature of the location where used and the location where stored
Temperature range for use：0～70℃, humidity 5～95%RH, no condensation
Temperature range for storage：-40～85℃,humidity 5～95%RH, no condensation
●
Make sure unit is grounded
(Ground with an AC3 pin connector.
If not grounded, electrical shock may occur upon contact
with the camera.)
Handling when moving or transporting the AC adapter
●Turn off the power and unplug the connected cables
(Make sure the power is turned off and the cables unplugged when moving the AC adapter. Fire,
electrical shock or malfunction may be caused.)
In addition to that mentioned above, unexpected problems may occur depending on the conditions of use of
this device. Therefore, carefully read the various items mentioned in this manual as well as in the user’s guide
for peripheral devices (or user’s manual) before using. Additionally, immediately contact the store if there
are any questions regarding this device.
11
(00375)

Safety Precautions
■Warning Labels
There are warning labels and displays in locations on the device that require precautions for safe use. Please
read these warnings before operating. Additionally, read the user’s guide or instruction manual for safe and
proper use.
Contact your store if you do not understand your device.
This describes the symbols shown on the warning labels.
●Safety alert symbol
This is an alert to you or other users of the potential danger during use of this
device. Carefully read the message next to this symbol an
d follow the instructions
for safe use of this device.
●Grounding terminal symbol
Indicates the site of a protective grounding terminal. If not grounded, electrical
shock may occur from the metallic and other parts of this device.
Make sure to ground to avoid danger.
●High voltage warning symbol
Indicates the site of high voltage that is dangerous if touched. When replacing
fuses, make sure to unplug the power cable from the outlet. Do not open the cover.
Depending on the device, some parts may
generate high voltage internally so
opening the cover may result in electrical shock.
Symbols Used on Warning Labels
12
(00375)

Safety Precautions
■Regular Replacement of Parts
・Memory Backup Battery
In general, replace the memory backup battery one year after purchase. However, if there is a rapid loss of
charge or problems during use, replace immediately. Replacement cannot be performed by users so contact
your store or our service center.
■Warranty
The warranty is valid for one year after purchase.
Refer to the attached warranty for details.
13
(00375)

This Booklet
This Booklet
About the notation in the text
A Indicates the page referenced
14
(00375)

Table of Contents
Table of Contents
Features of This Unit ............................................ 3
Safety Precautions................................................ 6
Reading this Manual ............................................14
Table of Contents ...............................................15
1 Introduction
Verify the Standard Components..................... 1-2
Main Options ..................................................... 1-4
External Appearance and Names for this Unit .. 1-5
Flow of Operations............................................ 1-9
２Preparations
Set Up this Unit................................................ 2-2
Mount the Lens................................................. 2-4
Connect the Equipment and Cables .................. 2-5
Status LED..................................................... 2-10
Turn the Power ON/OFF................................ 2-11
3 Basic Operations
Register the Image Correction Data.................. 3-2
Using HXLink ..................................................... 3-4
Get the Black Balance........................................ 3-6
Stop (STOP Mode).............................................. 3-9
Display Live Images (VIEW Mode).................... 3-10
Basic Recording Settings................................. 3-11
Using the Low Light Function ......................... 3-17
Start Recording (ARM Mode) ........................... 3-19
Trigger Input (REC Mode) ................................ 3-21
Memory Backup................................................ 3-22
Playback (PLAY Mode) ..................................... 3-24
Changing the Playback Speed .......................... 3-26
Saving Images .................................................. 3-27
Load and Save Settings................................... 3-29
Disconnect the HXLink and Camera .................3-32
4 Specifications
Image Sensor ......................................................4-2
Recorder.............................................................4-7
System Control ................................................4-14
Input/Output Connectors ................................4-17
Shape, Environment, Precision, Application
Standards, Supplies .........................................4-20
Main Attachments, Options.............................4-21
Dimensional Drawings ......................................4-23
15
(00375)

16
(00375)

1
Introduction
Verify the Standard Components...................... 1-2
Main Options...................................................... 1-4
External Appearance and Names for this Unit .. 1-5
Flow of Operations............................................ 1-9
1-1
(00375)

Verify the Standard Components
Verify the Standard Components
The following are included as standard components of the MEMRECAM Q1m/Q1v.
Make sure that all are included.
MEMRECAM Q1m/Q1v：Q1m/Q1v camera unit
Tripod plate：Plate to mount the camera to the tripod
Image compensation data CD：Image compensation data CD for the camera. Used with
control software.
The MEMRECAM Q1m/Q1v includes the following models.
Memory：4 / 8GB
Make sure the contents match the purchased model.
Do not use in a vibrating environment with the tripod plate mounted. Make sure to secure using
the camera unit screw holes.
Data for the various cameras is included on the image correction data CD. Store together with
the camera since it is used with the control software.
1-2
(00375)