NAD T 587 User manual

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
®
Owner’s Manual
T587
Blu-ray Disc™ Player

SAVE THESE INSTRUCTIONS FOR LATER USE.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE
AUDIO EQUIPMENT.
1 Read instructions - All the safety and operating instructions should be
read before the product is operated.
2 Retain instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
5 Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6 Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
9 A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10 Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
11 Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company.
The primary method of isolating the amplier from the mains supply
is to disconnect the mains plug. Ensure that the mains plug remains
accessible at all times. Unplug the AC power cord from the AC outlet if
the unit will not be used for several months or more.
12 Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will t into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to t, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
13 Power - Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
14 Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Section
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, species that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
15 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to lightning
and power-line surges.
16 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
17 Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of re or
electric shock.
18 Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a re or electric shock. Never spill
liquid of any kind on the product.
WARNING: THE APPARATUS SHOULD NOT BE EXPOSED TO
DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS.
AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL
LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A
FAILURE AND/OR A FIRE HAZARD.
IMPORTANT SAFETY INSTRUCTIONS
2
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

19 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualied service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualied technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) when the product exhibits a distinct change in performance-this
indicates a need for service.
20 Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
23 Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including ampliers)
that produce heat.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
CAUTION
This equipment employs a Laser System. To ensure proper use of this
product, please read this owner’s manual carefully and retain for future
reference. Should the unit require maintenance, contact an authorized
service location. Use of controls, adjustments or the performance of
procedures other than those specied may result in exposure to laser
radiation. To prevent direct exposure to laser beam, do not try to open the
enclosure. Visible laser radiation when the enclosure is opened.
DO NOT STARE INTO BEAM.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
INDUSTRY CANADA REQUIREMENT
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
THE EXCLAMATION POINTWITHIN AN EQUILATERALTRIANGLE IS
INTENDEDTO ALERTTHE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN
THE LITERATURE ACCOMPANYINGTHE APPLIANCE.
CAUTION
Changes or modications to this equipment not expressly approved by
NAD Electronics for compliance could void the user’s authority to operate
this equipment.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit
(from the largest outer dimensions including projections) that is equal to or
greater than shown below.
Left and Right Panels: 10 cm
Rear Panel: 10 cm
Top Panel: 50 cm
IMPORTANT SAFETY INSTRUCTIONS
3
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed
of with regular household waste but must be returned to a
collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user’s manual and
packaging, point this out.
The materials can be reused in accordance with their markings. Through
re-use, recycling of raw materials or other forms of recycling of old
products, you are making an important contribution to the protection of
our environment. Your local administrative oce can advise you of the
responsible waste disposal point.
INFORMATION ABOUT COLLECTION AND DISPOSAL OF
WASTE BATTERIES DIRECTIVE 2006/66/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION FOR
EUROPEAN CUSTOMERS ONLY
Batteries bearing any of these symbols indicate
that they should be treated as“separate collection”
and not as municipal waste. It is encouraged that
necessary measures are implemented to maximize
the separate collection of waste batteries and
to minimize the disposal of batteries as mixed
municipal waste.
End-users are exhorted not to dispose waste
batteries as unsorted municipal waste. In order to
achieve a high level of recycling waste batteries, discard waste batteries
separately and properly through an accessible collection point in your
vicinity. For more information about collection and recycling of waste
batteries, please contact your local municipality, your waste disposal service
or the point of sale where you purchased the items.
By ensuring compliance and conformance to proper disposal of waste
batteries, potential hazardous eects on human health is prevented and
the negative impact of batteries and waste batteries on the environment
is minimized, thus contributing to the protection, preservation and quality
improvement of the environment.
RECORD YOUR MODEL NUMBER NOW, WHILE YOU CAN SEE IT
The model and serial number of your new T 587 are located on the back of
the cabinet. For your future convenience, we suggest that you record these
numbers here:
Modelno:......................................
Serial no.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS
NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited
Copyright 2009, NAD Electronics International, a division of Lenbrook Industries Limited
4
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

INTRODUCTION
TABLE OF CONTENTS
THANK YOU FOR CHOOSING NAD.
The T 587 brings NAD’s penchant for performance to the exciting new
Blu-ray Disc format. This Prole 2.0 Blu-ray Disc Player brims with the latest
features and oers for the rst time a true High Denition source for digital
Home Theater systems.
As with all our products, NAD’s “Music First”design philosophy guided the
T 587’s design in such a way that it can condently promise you state-
of-the-art visual delity and audiophile-quality music listening for years
to come. We have been careful to ensure that the T 587 is as musically
transparent, faithful to every video detail and spatially accurate as possible,
incorporating much of what we’ve learned from a quarter-century’s
experience designing audio, video and home-theater components.
We encourage you to take a few minutes now to read right through this
manual. Investing a little time here at the outset might save you a good
deal of time later, and is by far the best way to ensure that you make the
most of your investment in the T 587.
One more thing: We urge you to register your T 587 ownership on the NAD
Worldwide Web site:
http://NADelectronics.com/warranty
For warranty information contact your local distributor.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .2
INTRODUCTION
GETTINGSTARTED...............................................6
UNPACKINGANDSETUP .............................................6
CHOOSINGALOCATION .............................................6
DISCLOADINGANDPLAYBACK ......................................6
QUICKSTART.........................................................6
GETTINGSTARTED...............................................7
REGION MANAGEMENT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
PLAYABLEDISCS......................................................7
ABOUTTHE SYMBOLDISPLAY.....................................7
BDROMDISCFEATURES.............................................7
BDROMDISCCOMPATIBILITY........................................7
IDENTIFICATION OF CONTROLS
FRONTPANEL....................................................8
REARPANEL .....................................................9
BR1REMOTECONTROL.........................................10
OPERATION
USINGTHET587................................................11
USINGTHEHOMEMENU........................................... 11
DISPLAYTHET587SETUPMENU................................... 11
NAVIGATING THE SETUP MENU OSD AND MAKING CHANGES. . . . . . 11
DISPLAYDISCOSD................................................. 11
DISPLAYSETUPMENU.............................................. 11
LANGUAGESETUPMENU .......................................... 13
AUDIOSETUPMENU............................................... 13
LOCK SETUP MENU APPLICABLE TO BD AND DVD PLAYBACK ONLY14
NETWORKSETUPMENU ........................................... 15
OTHERSSETUPMENU.............................................. 15
USINGTHET587FEATURES....................................16
USBMODE......................................................... 16
PLAYINGAUDIOCD/MP3/WMA.................................... 16
VIEWINGAPHOTOFILE ............................................ 17
DIVXPLAYBACK.................................................... 17
ENJOYING BDLIVE™ OR BONUSVIEW™ IN BDVIDEO . . . . . . . . . . . . . . . 17
SCREENSAVER...................................................... 17
USING THE T 587  FUNCTION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUDIO ............................................................. 18
SUBTITLE........................................................... 18
ANGLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ZOOM.............................................................. 18
RPTREPEAT....................................................... 18
MARKER............................................................ 18
REFERENCE
RESOLUTIONSETTINGS.........................................19
PLAYBACK OF UNPROTECTED MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PLAYBACK OF COPY PROTECTED MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LANGUAGECODELIST ..........................................20
AREACODE.....................................................21
TROUBLESHOOTING ............................................22
NOTESONDISCS................................................22
HANDLINGDISCS .................................................. 22
STORINGDISCS..................................................... 22
CLEANINGDISCS................................................... 22
SPECIFICATIONS................................................23
5
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

INTRODUCTION
GETTING STARTED
UNPACKING AND SETUP
WHAT’S IN THE BOX
Packed with your T 587 you will nd:
• An audio/video cable connector
• The BR 1 remote control with 2 (two) AA batteries
• A detachable AC power cord
• HDMI cable (European version only)
• This owner’s manual
SAVE THE PACKAGING
Please save the box and all of the packaging in which your T 587 arrived.
Should you move or otherwise need to transport your T 587, this is by far
the safest container in which to do so. We’ve seen too many otherwise
perfect components damaged in transit for lack of a proper shipping
carton, so please: Save that box!
CHOOSING A LOCATION
Choose a location that is well ventilated (with at least several inches to both
sides and behind), and that will provide a clear line of sight, within 23 feet/7
meters, between the T 587’s front panel and your primary listening/viewing
position. This will ensure reliable infrared remote control communications.
The T 587 generates a modest amount of heat, but nothing that should
trouble adjacent components. It is perfectly possible to stack the T 587 on
top of other components.
DISC LOADING AND PLAYBACK
There are two dierent disc sizes. Place the disc in the correct guide on the
disc tray. If the disc is out of the guide, it may damage the disc and cause
the T 587 to malfunction. “Check Disc”appears at the On-Screen Display
(OSD) (“DISC ERROR” at the VFD), if the disc is placed upside down (and it is
a single sided disc).
The following are important tips when loading a disc
• Do not push the disc tray while it is moving. Doing so may cause the
T 587 to malfunction.
• Do not push up the disc tray or put any objects other than discs on the
disc tray. Doing so may cause the T 587 to malfunction.
• Keep your ngers well clear of the disc tray as it is closing. Be especially
careful with children’s ngers around the closing disc tray, as there is a
risk of personal injury.
Press [ ] (Play), the disc tray is automatically closed. Playback of the rst
track starts if a CD is loaded. For BD, DVD, USB or other disc media, playback
operation is accessible through their menu screen.
NOTE
Do not move the T 587 during playback. Doing so may damage the disc
and the T 587.
ASSEMBLY OF RUBBER FOOT WITH PLASTIC FOOT
QUICK START
In case you simply cannot wait to experience the performance of your new
NAD T 587, we provide the following“Quick Start” instructions to get you
underway.
Please make all the connections to your T 587 with the unit unplugged. It is
also advisable to power-down or unplug all associated components while
making or breaking any signal or AC power connections.
PLAY A BLURAY DISC
1 Using a compatible HDMI connector, connect the T 587’s HDMI OUT to
the corresponding HDMI input of your HDMI-compatible TV/monitor.
2 Connect the supplied AC cord to the T 587 AC mains input and then
plug into an AC outlet. Follow the same for your HDMI-compatible TV
as applicable. Switch ON your TV and set it to the HDMI input where the
T 587 is connected.
3 Press the [OPEN/CLOSE] button to switch ON the T 587 and at the same
time open the disc tray.
4 Load the Blu-ray disc in the disc tray.
5 Press the front panel [PLAY/PAUSE] button or [ ] (Play) button of BR 1
remote control to close the disc tray and start playback. You should hear
audio and see an image on the TV/monitor. If one or the other fails to
appear, check your TV/monitor’s input settings or the T 587 audio/video
connections.
Enjoy the movie but be sure to set aside time to read this manual
thoroughly to set up and congure your T 587 according to your
preference.
Step 1 Insert rubber foot
Squeeze to allow the
rubber foot to clamp under
the six flanges on the
plastic foot
Plastic foot flange
Step 2
Rubber foot inserted
6
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

INTRODUCTION
GETTING STARTED
REGION MANAGEMENT INFORMATION
The T 587 is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc or Blu-ray disc. If the
Region or BD code described on the disc does not correspond to the Region
or BD code shown on the T 587 rear panel, the T 587 cannot play that disc.
The disc tray automatically opens after the OSD briey displays“This disc has
been coded for Region _ only and will not play in this machine. Please eject
this disc and play only on a Region _ player.”(BD only) or “Check Regional
Code”(DVD only) when an incompatible Region or BD disc is loaded.
PLAYABLE DISCS
The T 587 has exceptional playability. It has support for the following disc
formats
• Blu-ray Disc (BD), BD-R/RE discs that contain audio titles, DivX, MP3,
WMA or Photo les.
• DVD-Video, DVD±R, DVD±RW discs that contain audio titles, Movie,
DivX, MP3, WMA or Photo les.
• Audio CD, CD-R/-RW discs that contain audio titles, DivX, MP3, WMA or
Photo les.
• Advanced Video Codec High Denition (AVCHD) format discs.
ADVANCED VIDEO CODEC HIGH DEFINITION AVCHD
AVCHD video format is recorded using the MPEG-4 AVC/H.264 video compression
codec. It is a high denition digital video camera format used to record SD (standard
denition) or HD (high denition) signals.The MPEG-4 AVC/H.264 format enables a
HD video signal shot on a digital video camera recorder to be recorded on DVDs in
the same way as that of SD television signal.
“AVCHD” and the “AVCHD”logo are trademarks of Matsushita Electric
Industrial Co., Ltd. and Sony Corporation.
NOTES
• Youcannotplaybackdiscsotherthanthoselistedabove.Todosomay
render the T 587 permanently inoperable.
• AnAVCHDformatteddiscwillnotplayifitisnotcorrectlynalized.
• Dependingontherecordingcondition,someAVCHDformatdiscsmay
not play.
ABOUT THE SYMBOL DISPLAY
“ ” may appear on your TV display during operation. This indicates that
the function you entered or try to execute is not available on that specic
disc or le.
BDROM DISC FEATURES
BD-ROM (Blu-ray Disc Read-Only Memory) is a commercially produced disc
and available in the same capacities as that of regular Blu-ray discs. Other
than conventional movie and video contents, BD-ROM has enhanced
features such as interactive content, menu operations, pop-up menus,
subtitle selection, slideshow and other features.
BD-ROM Discs can store 25 GB (single layer) or 50 GB (dual layer) on a single
sided disc - about 5 to 10 times the capacity of a DVD. BD-ROM Discs also
support the highest quality HD video available in the industry (up to 1920 x
1080) - large capacity means no compromise on video quality. Furthermore,
a BD-ROM disc has the same familiar size and look as DVD.
The following BD-ROM disc features are disc dependent and will vary.
Appearance and navigation of features will also vary from disc to disc. Some
features may not be available on some discs.
VIDEO HIGHLIGHTS
The BD-ROM format for movie distribution supports three highly advanced
video codecs, includingMPEG-2, MPEG4 AVC (H.264), and SMPTE VC1. The
1920 x 1080 HD and 1280 x 720 HD video resolutions are also available.
HIGHDEFINITION PLAYBACK
To view high-denition contents from BD-ROM discs, an HDTV is required.
Some discs may require HDMI OUT for viewing of high-denition contents.
Ability to view high-denition contents in BD-ROM discs maybe limited
depending on the resolution of your TV.
GRAPHIC PLANES
Two individual full HD resolution (1920x1080) graphic planes (layers) are
available on top of the HD video layer. One plane is assigned to video-
related, frame accurate graphics (like subtitles), and the other plane is
assigned to interactive graphic elements, such as buttons or menus. For
both planes, various wipes, fades and scroll eects may be available.
MENU SOUND
When you highlight or select a menu option, sound can be heard such as
button clicks or a voice-over explaining the highlighted menu choice.
MULTIPAGE/POPUP MENUS
With DVD-Video, playback is interrupted each time a new menu screen
is accessed. Due to BD-ROM disc’s ability to preload data from the disc
without interrupting playback, a menu can consist of several pages. You can
browse through the menu pages or select dierent menu paths, while the
audio and video remain playing in the background.
INTERACTIVITY
Certain BD-ROM Discs may contain animated menus and/or trivia games.
USER BROWSABLE SLIDESHOWS
With BD-ROM Discs, you can browse through various still pictures while the
audio remains playing
SUBTITLES
Depending on what is contained on the BD-ROM disc, you may be able to
select dierent font styles, sizes and colors for some subtitles. Subtitles may
also be animated, scrolled or faded in and out.
BDJ INTERACTIVE CAPABILITY
The BD-ROM format supports Java for interactive functions.“BD-J”oer
content providers almost unlimited functionality when creating interactive
BD-ROM titles.
BDROM DISC COMPATIBILITY
The T 587 supports BD-ROM Prole 2. Aside from the BONUSVIEW function,
the T 587 supports BD-Live (BD-ROM version 2 Prole 2) discs that allow
usage of interactive functions when the T 587 is connected to the internet.
The T 587 is also compatible with discs supporting BONUSVIEW (BD-ROM
version 2 Prole 1 version 1.1/Final Standard Prole) that enables Virtual
packages or Picture-in-Picture functions.
NOTES
• Viewinghigh-denitioncontentandup-convertingstandardDVD
contentmayrequireanHDMI-capableinputorHDCP-capableDVIinput
on your display device.
• DolbyTrueHD,DolbyDigitalPlusandDTS-HDMasterAudioare
supportedwithmaximum7.1channelswhenHDMIOUTistheselected
audio output port.
• YoucanusetheUSBashdrivethatisusedtostoresomediscrelated
information,includingdownloadedon-linecontent.Thediscyouare
usingwillcontrolhowlongthisinformationisretained.
7
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

IDENTIFICATION OF CONTROLS
FRONT PANEL
1 STANDBY: Press this button to switch ON the T 587. If there is disc
loaded, the display window will show the playback time status of the disc
(applicable number and playback time of current track/chapter/title). If
there is no disc loaded, the VFD will briey show“NO DISC”and thereafter
show the default display“HOME”.
Pressing the [ ] button of the BR 1 will switch ON the T 587 from
standby mode and at the same time open the disc tray. The T 587 can
also be switched ON by pressing the [ON] or [ ] (Play) buttons of the
remote control. Pressing the standby switch again turns the unit back to
standby mode. Unplug the AC power cord from the AC wall socket to
completely shut down the T 587.
2 DISC TRAY: With the DISC TRAY open, insert a Blu-ray disc (BD), DVD,
CD or other compatible media disc face down onto the tray.
“Check Disc” appears at the On-Screen Display (OSD) (“DISC ERROR” at
the VFD), if the disc is placed upside down (and it is a single sided disc).
The disc tray will then automatically open.
3 VACUUM FLUORESCENT DISPLAY (VFD): If there is disc loaded, the
display window will show the playback time status of the disc. If there is
no disc inside, the display window will show“HOME”.
4 REMOTE SENSOR: Point the BR 1 at the remote sensor and press the
buttons. Do not expose the remote sensor of the BR 1 to a strong light
source such as direct sunlight or illumination. If you do so, you may not
be able to operate T 587 with the remote control.
Distance: About 23 ft (7 m) from the front of the remote sensor
Angle: About 30° in each direction of the front of the remote sensor
5 OPEN/CLOSE: Press this button to open and close the disc tray.
6 PLAY/PAUSE: This dual-function button alternates between starting
and stopping playback. Press this button to toggle between Play and
Pause of a BD, DVD, CD or other compatible media disc. Press to start
play or resume play after Pause. If the disc tray is open, press this button
to automatically close the tray and start playback if a CD disc is loaded.
During playback, press this button to stop playback temporarily,
keeping the optical pickup at its current position on the disc. To resume
playback at the exact point where it stopped, press [PLAY/PAUSE] again.
7 STOP: Except for BD playback, pressing this button will stop and at the
same time pause playback of the disc. Press [PLAY/PAUSE] button to
resume play from the spot it was stopped. For BD playback, pressing
the [STOP] button will fully stop the playback and will return you to the
TITLE or MENU option of the disc.
8 USB INPUT: Connect an external USB device into this input. Refer also
to the “USB MODE”section of “USING THE T 587 – FEATURES”under the
“OPERATION” main heading.
9 HOME: Press to access all the media for playback and setup of the
T 587. Refer also to the“USING THE HOME MENU”section of “USING THE
T 587” under the “OPERATION” main heading.
10 [ ] , [ ], ENTER: Press [ ] to skip forward or [ ]
to skip backward a track, le or chapter.
Press [ ] to scan fast-forward or fast-reverse during playback.
Each time the button is pressed, the speed increases until the maximum
level is reached. The scanning speed is indicated by trailing icons or
as shown in the OSD and may vary by disc type. The speed will be
retained even after the button is released; press [PLAY/PAUSE] to resume
normal playback.
The front panel [ ] , [ ] and ENTER buttons
respectively simulate the same functions of the [ ] and ENTER
buttons of the BR 1 remote control under the following conditions or
options only
• Navigating through the HOME menu and SETUP menu.
• Select through DivX or PHOTO les as contained in a disc.
Outside of the above conditions, the [ ] and [ ]
buttons normally function as SKIP and SCAN modes.
NOTE
 Notallmediasupportmaximumspeedsforscanning.
4 5 6 7 8 9 102 31
8
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

IDENTIFICATION OF CONTROLS
REAR PANEL
1 AC MAINS INPUT: The T 587 comes supplied with a separate AC Mains
cable. Before connecting the cable to a live wall socket, ensure rst
that it is rmly connected to the T 587’s AC Mains input socket. Always
disconnect the AC Mains cable plug from the live wall socket rst,
before disconnecting the cable from the T 587’s Mains input socket.
2 COMPONENT VIDEO OUT: Connect to the corresponding component
video input of a compatible equipment like a monitor/television,
projector, A/V receiver or processor. Be sure to observe consistency
in connecting the appropriate Y/ Pb/Pr jacks to the corresponding
sources/inputs. Do not rely purely on the color coding of the jacks,
which may not always be consistent among brands.
3 VIDEO OUT: Connect to the corresponding composite video input of
a compatible monitor/television, projector, A/V receiver or processor
using quality dual-RCA cable designed for video signals.
4 AUDIO OUT: This analog audio output can be connected to the
corresponding analog audio input of a compatible equipment like an
amplier, receiver, TV or stereo system.
5 DIGITAL OUT (COAXIAL, OPTICAL): The digital playback audio output
signal is available at these ports. Connect the optical or coaxial digital
OUT ports to the corresponding S/PDIF digital input of an amplier,
receiver, computer soundcard or other digital processors.
6 HDMI OUT: Using a HDMI cable (supplied only for European version
model), connect the HDMI OUT jack to the corresponding HDMI input
jack of a compatible equipment like a HDTV, a projector or an A/V
Receiver.
Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio are
supported with maximum 7.1 channels when HDMI OUT is the selected
audio output port. Make sure to connect to an amplier or receiver with
a built-in (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Digital
Plus, DTS-HD Master Audio and other applicable formats) decoder to
playback applicable multichannel audio formats.
WARNING
 BeforeconnectinganddisconnectinganyHDMIcables,boththeT587
andtheancillarysourcemustbepoweredOFFandunpluggedfromthe
ACoutlet.Failuretoobservethispracticemaycausepermanentdamage
toallequipmentconnectedviaHDMIsockets.
IMPORTANT NOTICE
 IfyourHDMIequippedTVisnotcapableofdecodingDTSorDolby
DigitalBitstream,settheT587’sHDMIorSPDIFsettingatthe“Audio
SetupMenu”to“PCMStereo”.Theremaybearushingnoiseheardifyour
TVisnotcapableofdecodingtheDTS(orDolbyDigital)Bitstream;most
TVsdonothavethiscapability.
7 LOCAL AREA NETWORK (LAN) PORT: Using a commercially available
straight LAN cable (Category 5/CAT5 or better with RJ45 connector),
connect this LAN port to the corresponding port of your modem
or router. By connecting the T 587 to broadband internet, you can
playback a disc that oers BD-Live function. Refer also to the“NETWORK
SETUP MENU” section of “USING THE T 587” under the “OPERATION”main
heading.
NOTES
• NADisnotresponsibleforanymalfunctionoftheT587and/orthe
internetconnectionduetocommunicationerrorsormalfunctions
associatedwithyourbroadbandinternetconnectionorotherconnected
equipment.ContactyourInternetServiceProvider(ISP)forassistanceor
theservicebureauofyourotherequipment.
• ContactyourISPforpolicies,charges,contentrestrictions,service
limitations,bandwidth,repairandotherrelatedissuespertinentto
internet connectivity.
• Somediscrelatedmaterialavailablethroughinternetmaynotbe
compatiblewiththeT587.Contacttheproducerofthediscforquestions
about such content availability or compatibility.
8 IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 587 from a remote location. Most NAD products with IR
OUT are fully compatible with the T 587.
3 4 5 81 2
ATTENTION!
 PleasemakesurethattheT587ispoweredoorunpluggedbeforemakinganyconnections.Itisalsoadvisabletopowerdownorunplugallassociated
componentswhilemakingorbreakinganysignalorACpowerconnections.
6 7
9
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

1 ON: Switch T 587 ON.
2 OFF: Switch T 587 OFF.
3 AUDIO: Select an audio language.
SUBTITLE: Select a subtitle language
ANGLE: Select a DVD camera angle if
available.
ZOOM: Enlarge video image.
4 0-9 number buttons: Select numbered
items in a menu.
5 RPT: Repeat track, chapter, title, le, folder,
all.
MARKER: Mark desired track or le number
for selective playback.
6 SCAN : Fast reverse or forward
search.
RES: Set output resolution of HDMI and
Component Video output.
HOME: Display or exit HOME menu.
PIP VIDEO: Switches ON/OFF secondary
video (Picture-in-Picture) (BD-ROM only).
PIP AUDIO: Switches ON/OFF secondary
audio (BD-ROM only).
7 TITLE/POP-UP: Display DVD title menu or
BD-ROM pop menu, if available.
MENU: Access menu on a DVD disc, if
available.
8 : Select an item in a menu.
ENTER: Acknowledge menu selection.
9 DISP: Access on-screen display.
RTN: Exit from a menu window.
10 : Opens and closes the disc tray.
: Stop playback.
: Pause playback temporarily.
: Go to beginning of current/
previous track, le or chapter; go to next
track/le/chapter.
: Start playback.
11 A,B,C,D : Navigate or select BD-ROM menu,
if applicable; Page up/down PHOTO and
MUSIC menu list.
IDENTIFICATION OF CONTROLS
BR 1 REMOTE CONTROL
1
3
5
7
9
11
10
6
4
2
8
10
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

You may operate the T 587 from its front panel or via the BR 1 remote
control. Since the remote control will be the primary controller for most
cases, we will focus on remote-controlled operations. Be sure also to read
the section, “IDENTIFICATION OF CONTROLS - FRONT PANEL”.
USING THE HOME MENU
From the Home Menu screen, you can access the Setup menu as well as
select desired media for playback. If the Home Menu does not appear,
check your applicable video connections.
1 Press [HOME] and the Home Menu appears.
2 Use [ ] keys to select among the following menu options - Movie,
Photo, Music or Setup. If there is no disc loaded, only “Setup”menu is
accessible from these Home Menu options.
3 Press [ENTER] to select menu option.
DISPLAY THE T 587 SETUP MENU
The Setup Menu allows one to customize the operation of the T 587. If the
factory defaults do not suit your taste, you will need to use the setup menu
to congure the T 587 yourself.
Press the BR 1’s [HOME] button and then select “Setup”for the Setup Menu
OSD to appear. With the use of the BR 1’s navigation buttons, you may
select various menus.
NAVIGATING THE SETUP MENU OSD AND MAKING CHANGES
To navigate through the Setup Menu OSD options, please do the following
using the BR 1 remote control:
1 Use [ ] keys to move up or down the menu selections.
2 Press [ ] to move backward or forward a menu window.
3 Use [ ] keys to select through the options of a particular menu
item.
4 Press [ENTER] to select a desired setting/selection.
5 Press [RTN] to exit the Setup menu.
DISPLAY DISC OSD
You can display the general disc playback status on the TV screen. Some
items can be changed using the menu. To use the on-screen display
1 Press the BR 1’s [DISP] during playback.
2 Press [ ] to select an item. The selected item is highlighted.
3 Key-in the desired the number button, press [ ] or [ENTER] as
applicable.
NOTES
• Thedisplayfeaturemaynotbeavailableforalldiscmediaandismedia
dependent.
• DisplaydiscOSDdoesnotapplytoaudioonlydiscslikeCDandMP3/
WMA/PHOTOlesastheyarealreadypresentedintheirrespectivemenu
screens.
• Ifnobuttonispressedforabout5seconds,theon-screendisplay
disappears.
DISPLAY SETUP MENU
TV ASPECT RATIO
Set TV ASPECT RATIO to select a picture size matching the aspect ratio of
your TV/Monitor.
Select “4:3 Letter Box” or “4:3 Pan Scan” when a standard 4:3 TV is connected.
4:3 Letter Box: Displays a wide picture with bands on the upper and
lower portions of the screen.
4:3 Pan Scan: Automatically displays the wide picture on the entire
screen and cuts o the portions that do not t.
Select “16:9 original” or “16:9 Wide” when a 16:9 wide TV is connected.
16:9 Original: The 4:3 picture is displayed with an original 4:3 aspect
ration, with black bars appearing at the left and right sides.
16:9 Wide: The 4:3 pictures is adjusted horizontally (in a linear
proportion) to ll the entire screen.
NOTE
 “4:3LetterBox”or“4:3PanScan”arenotselectablewhentheresolution
issettohigherthan480i/480p(576i/576p).
RESOLUTION
The T 587 provides several video output resolutions for the HDMI OUT
and COMPONENT VIDEO OUT jacks. Resolution can be changed via the
“Resolution”option in the DISPLAY SETUP menu or by toggling the [RES]
button of the BR 1 remote control. The T 587 must be at STOP mode when
BR 1’s [RES] button is used to change the RESOLUTION setting.
The following resolutions are selectable or available
Auto: If the HDMI OUT jack is connected to a TV that provides display
information, the T 587 automatically selects the resolution best suited
to the connected TV. If COMPONENT VIDEO OUT is the selected video
output media, the resolution changes to 1080i – the default resolution
for Component Video OUT.
1080p: Outputs 1080 lines of progressive video (applicable only for
HDMI connection).
1080i: Outputs 1080 lines of interlaced video.
720p: Outputs 720 lines of progressive video.
480p/576p: Outputs 480/576 lines progressive video.
480i/576i: Outputs 480/576 lines of interlaced video.
Available resolution varies according to connection and media format
OPERATION
USING THE T 587
11
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

HDMI OUT CONNECTION
• For the 480i/576i resolution setting, the output resolution of HDMI OUT
will change to 480p/576p.
• If you select a resolution manually and then connect the HDMI
jack to TV and your TV does not accept it, the resolution setting will
automatically be set to“Auto”.
• The 1080p video output frame rate may be automatically set to either
24Hz or 50/60Hz depending upon the capability and preference of the
connected TV and based on the native video frame rate of the BD-ROM
disc’s contents.
• If you select a resolution that is not compatible with your TV, a warning
message as shown below will appear.
After resolution change, if you cannot see the screen, please wait for about
20 seconds and the resolution will automatically revert back to the previous
resolution or a message screen as below may appear
Select “Yes”for the current resolution setting (the VFD will show the
current resolution setting) to be applied.“Current” resolution setting is the
suggested new resolution setting.
Select “No”to seek for the next applicable resolution setting. The above
“Warning” screens will interchangeably be displayed until you select “Yes”to
a suggested resolution setting.
COMPONENT VIDEO OUT CONNECTION
• For the 1080p resolution setting with unprotected media, the
COMPONENT VIDEO OUT resolution will change to 1080i.
• When a protected media is loaded for playback, 720p, 1080i or 1080p
resolution settings of COMPONENT VIDEO OUT will change to either
480i/576i or 480p/576p (depends upon the connectivity of a HDMI
cable - plugged-in or unplugged).
• BD or DVD could prevent up-scaling on analog output.
VIDEO OUT CONNECTION
• The resolution of the VIDEO OUT jack is xed to 480i/576i.
NOTES
• Dependingonyourdisplay,someoftheresolutionsettingsmayresult
to abnormal picture or the picture disappearing altogether. When this
happens,press[HOME]keyandthentoggle[RES]repeatedlyuntilthe
picture reappears.
• TheT587supportssimultaneousoutputofallvideooutjacks.The
resolutionoftheHDMIoutputwillnotbethesameastheresolutionon
theComponentVideooutput.
• Foralistofapplicableresolutionsettingswithrespecttovideooutput
portandtypeofmedia,pleasereferto“RESOLUTIONSETTINGS”under
the“REFERENCE”mainheading.
1080P DISPLAY MODE
Movies shot with lm camera consist of 24 frames per second. Since
conventional televisions display frames either at 1/60 or 1/50 second
intervals, the 24 frames do not appear at an even pace. The “24Hz” setting of
the T 587’s “1080p Display Mode”option enables the faithful reproduction
of such lm-based materials, displaying each frame at 1/24 second intervals.
24Hz: Using an HDMI-equipped display compatible with 1080/24p
input, set “1080p Display Mode”to “24Hz” for smooth presentation of
lm-based materials.
50/60Hz: If “24Hz” is selected and some picture disturbance is
experienced when the video switches between video and lm material,
set “1080p Display Mode”to “50Hz” (European version model only) or
“60Hz” (North America version model only) instead.
NOTE
 IfyourTVisnotcompatiblewith1080/24p,theactualframefrequency
ofthevideooutputwillbe50/60Hzeventhoughthe“1080pDisplay
Mode”issetto“24Hz”.
HDMI COLOR SETTING
Set the type of video output from HDMI OUT jack. Select the setting that
matches your display device.
YCbCr: Select when connecting to an HDMI display device.
RGB: Select when connecting to a DVI display device..
OPERATION
USING THE T 587
12
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

LANGUAGE SETUP MENU
DISPLAY MENU
Select a language for the SETUP menu and on-screen display.
DISC MENU/AUDIO/SUBTITLE
Select the language you prefer for the audio track (disc audio), subtitles
and the disc menu. Depending on the media, only those Disc Audio, Disc
Subtitle and Disc Menu languages recorded on the media are available.
When a language is chosen, it will become the default setting unless the
media overrides the settings.
Original: Refers to the original language in which the disc was
recorded.
Other: Select“Other”if the desired language is not on the list. Use [ ] to
highlight“Other”, press [ENTER] and then input the 4-digit language code using
the number keys of the remote control. If you enter the wrong language code,
complete entering the 4-digit numbers, press [ENTER] and then encode the
correct 4-digit numbers. See“LANGUAGE CODE LIST”under the main heading
“REFERENCE”for a list of applicable language codes.
O: If you choose for the disc subtitle not to come up, select “O”.
AUDIO SETUP MENU
Each BD/DVD disc has a variety of audio output options. Set the T 587’s
AUDIO options according to the type of audio system you use.
HDMI/SPDIF DIGITAL AUDIO OUTPUT
Select the audio output setting for HDMI OUT or DIGITAL AUDIO OUT port.
PCM Stereo: Select when connected to a two-channel digital stereo
decoder.
PCM Multi-Ch (HDMI only): Select when connected to a device with
multi-channel decoder. This is applicable to HDMI OUT only.
DTS Re-Encode: Select when connected to a device with DTS decoder.
Primary Pass-Thru: Select when connected to a device with LPCM,
Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and DTS-HD
decoder.
SAMPLE FREQ. FREQUENCY
Set the sampling frequency of the audio signal.
48KHz: If your receiver or amplier is not capable of handling 96 kHz
and 192 kHz signals, select 48 kHz. When this choice is made, this unit
automatically converts any 96 kHz and 192 kHz signals to 48 kHz so your
system can decode them.
96KHz: If your receiver or amplier is not capable of handling 192 kHz
signals, select 96 kHz. When this choice is made, this unit automatically
converts any 192 kHz signal to 96 kHz so your system can decode them.
192KHz: If your receiver or amplier is capable of handling 192 kHz
signals, select 192 kHz. When this choice is made, a 192 kHz signal
passes through without any further processing.
Check the documentation of your amplier to verify its capabilities.
DRC DYNAMIC RANGE CONTROL
You can select the eective dynamic range (subjective range from soft
to loud) for playback of Dolby Digital or Dolby Digital Plus soundtracks. It
is useful when you watch your favorite action movie without disturbing
others at night.
On: The “On” setting is for late-night sessions or other times when you
wish to retain maximum dialog intelligibility while minimizing overall
volume levels.
O: To maintain full dynamic range, set to “O”.
NOTE
 DRCsettingcanbechangedonlyatSTOPmodeorwhenthereisnodisc
loaded.
OPERATION
USING THE T 587
13
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

LOCK SETUP MENU APPLICABLE TO BD AND DVD PLAYBACK ONLY
Some movies contain scenes that may not be suitable for children to view.
Many of these discs contain parental control information that applies to
the complete disc or to certain scenes on the disc. Movies and scenes are
rated depending on the country. Some discs oer more suitable scenes as
an alternative.
PASSWORD
When you access Lock Setup Menu for the rst time, it is advised that you
setup rst your Password.
1 While at “Password” line menu, press [ ] to select “New” option.
2 Press [ENTER]. Input your desired 4-digit password code. Press [ENTER]
again.
3 Enter again the 4-digit password code for verication.
4 Press [ENTER]. You have now setup your Parental Rating password.
You can change the password for parental control. Enter your four-digit
password when prompted on the screen.
1 While at “Password” line menu, press [ ] to select “Change” option.
2 Press [ENTER].
3 Enter your old four-digit password using the numeric buttons (0-9).
Press [ENTER].
4 You will be prompted to enter your new password. Enter the new four-
digit password using the numeric buttons (0-9). Press [ENTER].
5 You will be prompted to verify your new password. Enter the new four-
digit password again.
6 Press [ENTER]. The new four-digit password is now valid.
The setup Password can be deleted by the following procedure
1 While at “Password” line menu, press [ ] and then [ ] to select
“Delete” option.
2 Press [ENTER].
3 Enter your four-digit password using the numeric buttons (0-9). Press
[ENTER]. The password is now deleted.
RATING
The parental rating feature allows you to block access to scenes greater
than the rating you set up, thereby preventing your children from viewing
material you believe is unsuitable. To activate “Rating”, please be guided by
the following:
1 While at “Rating”line menu, press [ ]. A “Password” prompt will come
up in the menu screen.
2 Input the password you have setup.
3 Upon entering the password, you can now set the parental rating level
you prefer. Use [ ] to step through the rating levels.
4 Press [ENTER] to conrm your rating selection.
RATING 18
Rating “1” has the most restrictions and Rating “8” is the least restrictive.
UNLOCK
If you select “Unlock”, parental lock is not active and the disc plays in full.
NOTE
 Ifyousetaratinglevelfortheplayer,alldiscsceneswiththesamerating
levelorlowerareplayed.Higherratedscenesarenotplayedunlessan
alternate scene is available on the disc. The alternative must have a
lowerrating.Ifnosuitablealternativeisfound,playbackstops.Youmust
enterthe4-digitpasswordinordertoplaythedisc.
Should you forget your password, you can reset it by using the following
steps.
1 Remove any disc loaded.
2 Select “Password” option.
3 Use the number button to enter“210499”. “PIN CLEAR” appears in the
VFD and the password is reset.
BD AGE
Set an age limit for rated BD-ROM playback.
1 While at “BD Age” line menu, press [ ]. A “Password”prompt will come
up in the menu screen.
2 Input the password you have setup.
3 Upon entering the password, you can now set the age limit for BD
viewing.
255: All BD ROM can be played back.
0 - 254: Prohibits playback according to the ratings recorded on the BD
ROM.
4 Press [ENTER] to conrm your BD Age selection.
AREA CODE
Enter the code of the country/area whose standards were used to rate your
DVD. See“AREA CODE LIST” under the main heading “REFERENCE”for a list of
applicable area codes.
1 While at “Area Code” line menu, press [ ]. A “Password”prompt will
come up in the menu screen.
2 Input the password you have setup. Press [ENTER].
3 Select the rst character using [ ] buttons. Press ENTER.
4 Select the second character using [ ] buttons.
5 Press ENTER to conrm your area code selection.
OPERATION
USING THE T 587
14
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NETWORK SETUP MENU
The NETWORK settings are needed to use the BD Live feature. By
connecting the T 587 to the internet, special BD-ROM sites can be enabled
by some BD-ROM discs. Online contents can be downloaded and watched
if a BD-ROM site contains links to future movie trailers, bonus contents and
other related features.
Ensure proper broadband connectivity when conguring the following
NETWORK features.
IP MODE
If there is a DHCP server on the local area network (LAN), the T 587 will
automatically be allocated an IP address.
Dynamic IP: Select if you’re using a broadband router or broadband
modem that has a DHCP (Dynamic Host Conguration Protocol) server
function. The IP address will automatically be determined.
Static IP: Select if there is no DHCP server on the network and you
want to set the IP address manually. Scroll down to “IP Setting”below for
the conguration of the applicable IP settings.
IP SETTING
This option is available only if “IP Mode”option is set to “Static IP”.
1 Use the [ ] buttons to select a eld.
2 Enter a value by using the number buttons.
3 Press [ENTER] when“OK” is highlighted to nish and exit the IP Setting
screen.
BDLIVE CONNECTION
You can restrict Internet access when BD-Live functions are used.
Permitted: Internet access is permitted for all BD-Live contents.
Partially permitted: Internet access is permitted only for BD-Live
contents that have content owner certicates. Internet access and
AACS Online functions are prohibited for all BD-Live contents without
a certicate.
Advanced Access Content System (AACS) is a standard for content
distribution and digital rights management, intended to restrict access
to and copying of the next generation of optical discs and DVDs. The
AACS standard has been adopted as the access restriction scheme for
Blu-ray Disc.
Prohibited: Internet access is prohibited for all BD-Live contents.
OTHERS SETUP MENU
SKIN
Change the background or wallpaper of the OSD. Select among Fantasy,
Dream, City and Passion. The default “Skin” is “Fantasy” which is actually the
NAD logo.
JAVA FONT SIZE BD ONLY
You can adjust the default text size displayed for the BD-J contents during
BD-ROM playback. This setting is only valid when BD-J contents do not set
the size of text. Please select a font size bigger than 24 when the T 587 is
connected to an HDTV.
INITIALIZE
You can reset the player to its original factory settings or initialize the BD
contents of the connected USB device.
Factory Set: Select to restore the T 587 to its factory default settings
except the LOCK SETUP MENU settings.
BD Storage Clear: Delete the BD contents from the connected USB
device.
For both of the above options, the conrm message prompt appears to
complete the selection. Use [ ] to select “Yes” or “No”and then press
[ENTER].
DIVX REGISTRATION CODE
DivX is the name of a revolutionary new video codec which is based on the
new MPEG-4 compression standard for video. You will be able to play DivX
discs using the T 587.
The Registration code details necessary for VOD (Video-On- Demand)
service can be shown by pressing [ ] or [ENTER] while at “DivX Reg. Code”
menu option.
OPERATION
USING THE T 587
15
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

USB MODE
The T 587 can play back MP3/WMA/PHOTO/PNG/DivX les stored in
external USB (Universal Serial bus) devices. The following are the T 587’s
capabilities with respect to USB device playability.
• Support only USB Flash Drive.
• Support USB 1.1 and USB 2.0.
• Support up to 4 partitions of the USB device.
• Digital camera and mobile phone are not supported.
• If a USB extension cable or USB HUB is used, the USB device may not be
recognized.
USB PLAYBACK
1 Connect the external USB device to the front panel’s USB input.
2 Press [HOME]. Select“Movie”, “Photo” or “Music” option. Press [ENTER].
3 If a disc is loaded and a USB device is inserted simultaneously, the menu
prompt for selecting a media will appear
4 Select “USB” as the desired media and then press [ENTER].
For details of operations on applicable le type, refer to the relevant
sections below about MP3/WMA/Photo/DivX playback.
PLAYING AUDIO CD/MP3/WMA
The T 587 can play Audio CD and MP3/WMA formatted recordings on
CD-R/RW, DVD±R/RW,BD-R/RE discs or USB ash drive.
1 Load the applicable disc or connect USB containing les. Select “Music”
from the “Home” menu.
2 Press [ENTER]. The “MUSIC”menu appears at the OSD. A list of folders,
tracks or les is shown at the OSD.
3 Use the BR 1’s [ ] keys to navigate through the folders, tracks or
les.
4 Press [ ] to select a folder, and press ENTER to see the folder
contents.
5 Press [ ] to select a track or le.
6 Press [ ] (Play) to start playback or press [ENTER] for more options - the
drop down playability menu appears.
Play: Start playback of the selected track or le.
Select Play: Playback only the marked track(s) or le(s). Use BR 1’s
[MARKER] for selecting the multiple les or tracks.
Random: Start or stop random playback. Press [ ] during random
playback to select another random track or le. “Random” and “Select
Play” mode cannot be enabled simultaneously.
Unmark All: Unmark all marked tracks or les.
Close: Exit menu options.
NOTES
• PlaybackmaystartautomaticallyifanAudioCDisloaded.
• IfyouareinalelistandwanttoreturntothepreviousFolderlist,use
the[ ]buttonsontheremotetohighlight“UPFolder”andpress
[ENTER].
• At“MUSIC”menu,BR1’sredorbluecolorbuttoncanbeusedtomoveto
thepreviousornextpage.
IMPORTANT NOTICE
• Customersshouldnotethatpermissionisrequiredinordertodownload
MP3/WMAlesandmusicfromtheInternet.NADELECTRONICS
INTERNATIONALhasnorighttograntsuchpermission.Permission
shouldalwaysbesoughtfromthecopyrightowner.
• Maximumlesperdisc/USB:lessthan1999(totalnumberoflesand
folders).
OPERATION
USING THE T 587  FEATURES
16
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

VIEWING A PHOTO FILE
The T 587 allows the playback or viewing of PHOTO les.
1 Load the applicable disc or connect USB containing les. Select “Photo”
from the “Home” menu. Press [ENTER].
2 The PHOTO menu appears on the TV screen. A thumbnail of the photos
loaded in the disc will be shown in the OSD.
3 Press [ ] to go over the photo les.
4 Press [ENTER] or [ ] (Play) to to select a le and start playback.
5 During photo playback, several selectable options are shown in the
bottom portion of the photo. Use [ ] to highlight and select any of
the following options.
Slide Show: Press [ENTER] button to start or pause the slide show.
Music: Press [ENTER] to play or pause the background music. This
option is available after the background music is selected using [Music
Select] option.
Rotate: Toggle [ENTER] to continually rotate the picture clockwise. This
option is not available during slide show.
Normal/Fast/Slow: Toggle [ENTER] to set the Slide Show speed.
Music Select: Select the background music during photo playback.
Press [ENTER] and the“Select the music album”submenu appears.
Use [ ] to select a media or folder containing music les.
Press ENTER to conrm your selection and start playback of selected
background music.
Close: Press [ENTER] to exit the menu option.
NOTES
• PlaybackmaystartautomaticallyifanAudioCDisloaded.
• IfyouareinalelistandwanttoreturntothepreviousFolderlist,use
the[ ]buttonsontheremotetohighlight“UPFolder”andpress
[ENTER].
• Togodirectlytoanyle,enterthelenumberusingthenumbered
buttons(0-9).
• At“PHOTO”menu,BR1’sredorbluecolorbuttoncanbeusedtomoveto
thepreviousornextpage.
• Recommendedsize:lessthan3000x3000x24bit/pixelorlessthan
3000x2500x32bit/pixel.
• Maximumlesperdisc/USB:lessthan1999(totalnumberoflesand
folders).
DIVX PLAYBACK
The T 587 supports DivX playback.
1 Load the applicable disc or connect USB containing les. Select “MOVIE”
from the “Home” menu.
2 Press [ENTER]. A list of DivX les is shown in the OSD. Use [ ] to
select a le.
3 Press [ENTER] to select a le and start playback.
NOTES
• Availableresolutionsize:720x576(WxH).·Maximumlesperdisc/
USB:lessthan1999(totalnumberoflesandfolders).
• OntheMOVIEmenu,useBR1’sredorbluecolorbuttontomovetothe
previousornextpage.
ENJOYING BDLIVE™ OR BONUSVIEW™ IN BDVIDEO
The T 587 supports picture-in-picture (PIP), secondary audio, Virtual packages
and other features for BD-Video supporting BONUSVIEW (BD-ROM version
2 Prole 1 version 1.1/ Final Standard Prole). In addition to the BONUSVIEW
function, BD-Video supporting BD-Live (BD-ROM version 2 Prole 2) allow more
functions like online games by connecting the T 587 to the internet.
PLAYING SECONDARY VIDEO PICTUREINPICTUREAND
SECONDARY AUDIO
Secondary video can be played from compatible discs that support picture-
in-picture function. Refer to your disc’s instructions for the playback method
of this feature.
PIP VIDEO: Press to turn ON/OFF secondary video.
PIP AUDIO: Press to turn ON/OFF the audio of the secondary video. If
secondary video is turned OFF, secondary audio will not be available.
ENJOYING BDLIVE DISCS
The T 587 supports BD-Live, a new BD-Video function that allows access
features like interactive functions when connected to the internet. The
usable functions and the operating method may vary with each disc so
make sure to refer to the disc’s instructions for proper access and playability.
The T 587 must be connected to the internet to use the BD-Live functions.
It may take up to several minutes to load and start enjoying BD-Live
contents. Additional contents like movie trailer, subtitles, BD-J and similar
features can be downloaded to a USB device. Make sure that the free space
in the USB device is more than 1GB.
IMPORTANT NOTICE
 EnsurethataUSBashdriveisconnectedinthefrontUSBportwhen
accessingBD-Livefunctions.
SCREENSAVER
The screensaver appears when you leave the T 587 in Stop mode or HOME
menu mode for about ve minutes. The Screensaver will be continuously
displayed until the next command is executed.
OPERATION
USING THE T 587  FEATURES
17
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Depending on the media, the following basic function controls of the T 587
can be accessed directly using the BR 1 remote control.
AUDIO
The AUDIO button will allow one to switch the audio language or format
only if the media supports the AUDIO button feature.
Press [AUDIO] repeatedly to select desired audio language or format.
SUBTITLE
It is possible to change the subtitle language to a dierent language from
the one selected at the initial settings. This operation works only with discs
on which multiple subtitle languages are recorded.
1 Press [SUBTITLE] during playback. When no subtitles are recorded,“OFF”
will be displayed.
2 Press [SUBTITLE] repeatedly until the desired language is selected.
When the desired language is not selected even after pressing the button
several times, it means that the language is not available on the disc.
To eliminate the On Screen Subtitles, press [SUBTITLE] repeatedly to select
“OFF”.
ANGLE
Some DVDs may contain scenes that have been shot simultaneously from a
number of dierent angles. For these discs, the same scene can be viewed
from each of these dierent angles using the [ANGLE] button. This function
only works for discs having scenes recorded at dierent angles.
1 Press [ANGLE] during playback. Angle number will be displayed.
2 Press [ANGLE] repeatedly until the desired angle is selected.
ZOOM
Use [ZOOM] to enlarge the video image. Press [ZOOM] during playback or
still playback to activate the Zoom function.
Use [ ] to select zoom mode (up to 16 steps). To resume normal
playback, press [ZOOM] repeatedly until “O”.
NOTE
 Zoommaynotworkonsomediscsortitles.
RPT REPEAT
To repeat the playback of a particular track or chapter, press the T 587’s
[RPT] key once. Pressing the same [RPT] key a second time will repeat all the
tracks or title. Turn o repeat mode by pressing [RPT] button a third time.
NOTE
 REPEATfeaturedoesnotapplytoPHOTOles.
MARKER
Use the [MARKER] button to selectively mark or check the track(s) or le(s)
that you wish to playback. Choose “Select Play”from drop down playability
menu (see section above about “PLAYING AUDIO CD/MP3/WMA”) to
playback in chronological order the marked tracks or les.
OPERATION
USING THE T 587  FUNCTION CONTROL
18
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

PLAYBACK OF UNPROTECTED MEDIA
VIDEO OUTPUT
RESOLUTION HDMI OUT
COMPONENT VIDEO OUT
VIDEO OUT
HDMI CONNECTED HDMI DISCONNECTED
480i/576i 480p/576p 480i/576i 480i/576i 480i/576i
480p/576p 480p/576p 480p/576p 480p/576p 480i/576i
720p 720p 720p 720p 480i/576i
1080i 1080i 1080i 1080i 480i/576i
1080p/24Hz mode 1080p/24Hz mode 480i/576i 1080i 480i/576i
1080p/60Hz mode 1080p/24Hz mode 480i/576i 1080i 480i/576i
PLAYBACK OF COPY PROTECTED MEDIA
VIDEO OUTPUT
RESOLUTION HDMI OUT
COMPONENT VIDEO OUT
VIDEO OUT
HDMI CONNECTED HDMI DISCONNECTED
480i/576i 480p/576p 480i/576i 480i/576i 480i/576i
480p/576p 480p/576p 480p/576p 480p/576p 480i/576i
720p 720p 480i/576i 480p/576p 480i/576i
1080i 1080i 480i/576i 480p/576p 480i/576i
1080p/24Hz mode 1080p/24Hz mode 480i/576i 480p/576p 480i/576i
1080p/60Hz mode 1080p/24Hz mode 480i/576i 480p/576p 480i/576i
REFERENCE
RESOLUTION SETTINGS
19
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Use this list to input your desired language for the following settings: DISC AUDIO/DISC SUBTITLE/DISC MENU language.
REFERENCE
LANGUAGE CODE LIST
Language Code
Abkhazian 6566
Afar 6565
Afrikaans 6570
Albanian 8381
Ameharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Aymara 6588
Azerbaijani 6590
Bashkir 6665
Basque 6985
Bengali; Bangla 6678
Bhutani 6890
Bihari 6672
Breton 6682
Bulgarian 6671
Burmese 7789
Byelorussian 6669
Cambodian 7577
Catalan 6765
Chinese 9072
Corsican 6779
Croatian 7282
Czech 6783
Danish 6865
Dutch 7876
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079
Language Code
Fiji 7074
Finnish 7073
French 7082
Frisian 7089
Galician 7176
Georgian 7565
German 6869
Greek 6976
Greenlandic 7576
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7387
Hindi 7273
Hungarian 7285
Icelandic 7383
Indonesian 7378
Interlingua 7365
Irish 7165
Italian 7384
Japanese 7465
Javanese 7487
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kirghiz 7589
Korean 7579
Kurdish 7585
Laothian 7679
Latin 7665
Latvian, Lettish 7686
Language Code
Lingala 7678
Lithuanian 7684
Macedonian 7775
Malagasy 7771
Malay 7783
Malayalam 7776
Maltese 7784
Maori 7773
Marathi 7782
Moldavian 7779
Mongolian 7778
Nauru 7865
Nepali 7869
Norwegian 7879
Oriya 7982
Panjabi 8065
Pashto, Pushto 8083
Persian 7065
Polish 8076
Portuguese 8084
Quechua 8185
Rhaeto-Romance 8277
Rumanian 8279
Russian 8285
Samoan 8377
Sanskrit 8365
Scots Gaelic 7168
Serbian 8382
Serbo-Croatian 8372
Shona 8378
Sindhi 8368
Language Code
Singhalese 8373
Slovak 8375
Slovenian 8376
Somali 8379
Spanish 6983
Sudanese 8385
Swahili 8387
Swedish 8386
Tagalog 8476
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga 8479
Turkish 8482
Turkmen 8475
Twi 8487
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapük 8679
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 7473
Yoruba 8979
Zulu 9085
20
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ