NAMCO TEKKEN 4 User manual

TEKKEN 4
Game PC Board Kit
l To ensure safe operation of the product, be we to read this Operatim Manual before use.
l Keep this Operation Manual in a safe place for quick access.
NAMCO AMERICA INC

Read PRECAUTIONS and INSTALLATION
Sections before operating game
Note: This equipment uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
No part of this publication may be reproduced by any mechanical photographic, or
electronic process, or in the form of a phonographic recording, nor may it be stored in
a retrieval system, transmitted, or otherwise copied for public or private use, without
permission from NAMCO AMERICA INC.

INTRODUCTION
Thank you for purchasing the Tekken 4 Game PC Board Kit (hereafter referred to as “the product”).
This operation manual describes:
0How to operate the product correctly and make full use of its features
0How to conduct the following procedures safely
0installation and connection of the product to a general-purpose game ma-
chine cabinet (hereafter referred to as “the cabinet”)
0Adjustment for operation
0Operation
0Inspection, cleaning and troubleshooting
0Removal, storage and transportation
0Disposal
Inquiries concerning the product and repairs
0For further information about the product and repairs, contact your distributor.
You are hereby notified that this product (PC board) falls within the scope of national export
control regulation according to the Foreign Exchange and Foreign Trade Control Law. The prod-
uct must not be taken out of Japan without permission of the Minister of Economy, Trade and
Industry, except in a special case specified by the Law (as of June 27,ZOOl).
MAG ICGATE is a term to describe a copyright protection technology created by Sony
Group. This MAGICGATE mark does not necessarily guarantee compatibility with
other products bearing the “MagicGate” trademark.
MAGICGATE is a trademark of Sony Corporation.
The DVD-ROM supplied with the product must not be copied, modified, distributed,
or used for purposes other than the operation of the product. Copyright laws pro-
tect the contents of the DVD-ROM. Infringement of copyright laws may be subject
to criminal penalties.
Do not use the supplied DVD-ROM with other product models or other media for-
mats. Doing so may result in equipment failure.

Dear Customers,
JULY,2001
Thank you for purchasing the TEKKEN 4 PCB kit. This notice to inform you that the Dongle in
this kit is not installed in the PCB Rack assy. Please follow the following instructions tu make sure
that the dongles are fitted properly to the PCB.
Best regards
Dongle adjustments-To be conducted by technicians only
r3m *The dongle included in this kit, is limited in usage for this product only.
Please DO NOT insert the dongle in other games. Inserting dongles to
other products may cause defects.
*Please make sure that the power is turned off before inserting the dongle.
1 . Loosen the screws (round head philip screws M3 x 6) and remove the Dongle
cover.
2 . Insert the dongle in the slot located on the left side, make sure that the barcode
label on the dongle is facing up, and then press the dongle in until you have
confirmed that the dongle has been locked with the connector properly.
3 When finished refit the dongle cover using the screws (round head philip
screws M3 x 6) that were attached to the cover.
Round head philip screws
M3x6
/
/

I. SAFETY PRECAUTIONS. Be sure to read these instructions to ensure safety-
Instructions to the owner:
l If you entrust another party to perform installation, connection, adjustment, operation, inspec-
tion, cleaning, troubleshooting, removal, storage, transportation or disposal of the product, in-
struct the concerned party to read and observe all the instructions and precautions in this opera-
tion manual regarding the particular action to be taken.
0When transferring the ownership of the product, be sure to provide this operation manual to-
gether with the PC board kit.
l-l Magnitudes of risk
On labels and in this operation manual, safety precautions and property damage
are classified as listed below in accordance with the magnitude of the particular
risk.
AWARNING :
Failure to avoid the risk may result in death or serious injury.
A CAUTION
: Failure to avoid the risk may result In minor injury.
Functional notes not related to safety are marked with the following label:
Bm
: Notes related to a function or protection of the product
1-2 Target readers of this operation manual
Thisoperationmanualiswrittenforarcadepersonnel.However,thesectionsmarked
“To be conducted by a technician only” in the table of contents and with the section
titles are written for technicians. These tasks must be conducted by technicians
only.
Technician: A person engaged in machine design, manufacture, inspection
or maintenance for a manufacturer of amusement equipment,
or a person who has technical knowledge related to electricity,
electronics or mechanical engineering at a level equal to or
higherthan that of technical high school graduates, and who is
engaged routinely in maintaining (repairing) amusement equip-
ment.
1

I. SAFETY PRECAUTIONS -Be sure to read these instructions to ensure safety -
I-3 Top-priority safety precautions
1-3-I General precautions
I &VARNING
0Do not disassemble or modify the product. Also never perform work not described
in this operation manual. Failure to observe this caution can result In an electrical
shock or fire, and may disallow you from receiving repair services.
0The product is designed for indoor use only. Do not install, connect or operate the
product outdoors. Installation, connection or operation of the product conducted
outdoors can cause an electrical shock or fire.
0Use only the specified parts fo replace consumable and service parts (including
screws). Use of other parts can result in a fire or electrical shock.
To order parts, contact your distributor.
0Do not perform work with wet hands to prevent an electric shock.
0Before installing, connecting, inspecting, cleaning, troubleshooting, or removing the
product, turn off the power switch on the cabinet, and unplug the power cord from
the service outlet to prevent an electrical shock.
l-3-2 Safety precautions for installation and connection
I &VARNING
Connection to JAMMA STANDARD conforminq cabinet (JAMMAW PC board kit (optional) is
required)
0The power supplied from the cabinet connected to the JAMMA edge connector must
comply with the following specifications.
* +5V power supply - allowed voltage fluctuation *5%, current: 7 A or higher
l+lZV power supply - allowed voltage fluctuation +5%, current: 2 A or higher
Use of non~conforming power supply can cause a fire.
Connection to JAMMAVIDEO STANDARD(JVS) conformins cabinet
l The power supplied from the cabinet connected to the power cord must comply with
the following specifications.
l +5V power supply -
allowed voltage fluctuation *5%, current: 7 A or higher
l +12V power supply -
allowed voltage fluctuation +5%, current: 2 A or higher
Use of non-conforming power supply can cause a fire.
2

1. SAFETY PRECAUTIONS -Be sure to read these instructions to ensure safety.
I-3-3 Cautions in operation
I AWARNING
l Should any problem occur, such as an abnormal odor or noise, turn off the power
switch on the cabinet immediately to stop the machine operation. Then, unplug the
power cord from the service outlet, and contact your distributor. Operating the
msrhina uri+h snrnhlnm Id+ ,,nr~rm,.+,w, mst, PC.IICI in .In,.+.ir.l chmrlr nr ii.,,
.~IYYII.II” . . ..I. u f,‘““‘...,. I*,. YIIUUIII”...” “W, “““II “II Il~s,.ll”Yl lll”Yl. “I .,,r.
l Make sure that the product has been installed and connected according to the
directions (refer to P. 9 “5. Installation and Connection”) in this operation manual
before operating. Incorrect installation or connection can cause a fire, electrical shock
or malfunction.
l-3-4 Cautions for disposal
AWARNING
0Never throw the product into flames. The lithium battery contained in the product
can explode and cause injuries.
l When discarding the product, be sure to collect, transport and dispose of the product
according to the law.
l When entrusting another party to collect, transport and dispose of the product, be
use to use a company specializing in the particular work to be assigned.
3

CONTENTS
INTRODUCTION
1. SAFETY PRECAUTIONS - Be sure to read these instructions to ensure safety -.............................
1
l-l Magnitudes of risk .........................................................................................................................................
1
l-2 Target readers of this operation manual
........................................................................................................
1
l-3 Top-priority safety precautions ..................................................................................................................... ,2
I-3-1 General precautions ............................................................................................................................. 2
l-3-2 Safety precautions for installation and connection ............................................................................... 2
i-3-3 Cauttonstnoperation .. . ........ ..................... 1;.
.... .Z.. ;...Y ..I.. ....... ... . ................ Z.. ..Z.. ... I.. .................... 3
l-3-4 Cauttons for disposal.. .......................................................................................................................... 3
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......................... 4
2. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......... 6
3. CHECKING THE PACKAGE CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. NAMES OF PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....... 8
5. INSTALLATION AND CONNECTION - To be conducted by a technician only -
............................... 9
5-1 Preparation for installation KW 5!H .......................................................................................................... 10
5-2 Installation of PC board and JAMMA PC board to mounting plate of JAMMA STANDARD
conforming cabinet m.. ............................................................................................................................. 11
5-3 Installation of PC board to mounting plate of JAMMA VIDEO STANDARD (JVS) conforming
cabinetm.. ............................................................................................................................................... 13
5-4 Connection toJAMMA STANDARD conforming cabinet m ...................................................................... 15
5-4-l Checking the JAMMA edge connectorm ......................................................................................... 15
5-4-2 Checking the extension harnessm. .................................................................................................. 16
5-4-3 Connecting to the control panelm .................................................................................................... 17
5-4-4 Connecting the speakerm ............................................................................................................... 19
,5-4-5 Connecting the connector m ............................................................................................................ 20
5-5 Connection to JAMMA VIDEO STANDARD(JVS) conforming cabinet=. .............................................. .22
5-5-l Connecting to the control panel m.. ................................................................................................ 22
5-5-2 Connecting the cable m .................................................................................................................. 23
5-6 Inserting the DVD-ROM m/m .............................................................................................................. 25
5-7 Attaching the stickers a/m. ................................................................................................................. 27
6. ADJUSTMENT FOR OPERATION...................................................................................................... 28
6-l Basic information for adjustment ................................................................................................................. 26
6-l-l Adjustment switches and knob.. ........................................................................................................ .29
6-l-2 Selection of adjustment item .............................................................................................................. 30
6-I-3 Exiting from test mode ........................................................................................................................ 32

CONTENTS
6-2 DISPLAY TEST (checking and adjusting screen display) ._,.,,,,,,,,,,,,,,,,,,,,,,,,,,,,.,,.,,.,,,,,,,,,,,,,,,,,,,,,.,,,.,.,.,,,,,, 32
6-2-l Common procedures .......................................................................................................................... 33
6-2-2 CONVERGENCE
(checking and adjusting display size, display position, aspect ratio, distortion). ................................ 34
6-2-3 COLOR EDIT, COLOR BAR
(adjusting contrast and color of video signal output from the PC board) ............................................ 35
6-2-4 INTERLACE CHCK
(switching between interlace and non-interlace modes) ................................................................... .37
6-3 INPUT TEST (testing switches) .................................................................................................................. .39
6-4 SOUND TEST (testing and setting sound) .................................................................................................. 40
6-5 JVS STATUS (display of status of JAMMA VIDEO STANDARD (JVS) conforming cabinet) m ............... 41
6-6 GAME OPTIONS (setting game options) .................................................................................................... 42
6-7 COIN OPTIONS (setting game pricing) ....................................................................................................... 44
6-6 A.D.S. (checking data of past game plays) .......................................... ...................................................... .46
6-9 DATA CLEAR (deleting data and resetting to defaults) ............................................................................... 46
7. OPERATION
7-I Persons who should not play the game ...................................................................................................... 49
7-2 Operating environment ................................................................................................................................ 49
7-3 Play instructions .......................................................................................................................................... 50
8. INSPECTION, CLEANING AND TROUBLESHOOTING - To be conducted by a technician only - 51
6-1 Inspection and cleaning .__.._._...._.._,.,,.,,.,..,,,.,,,,..,..,,,.,.,,,.,.,,,,,,.,.,,,,.,,,,,.,,,..,.,..........................,,..,..,,,,.,.,..... 51
6-2 Troubleshooting ..,,,.,,.,.,,_._,,....,..............,.,,.,.,,,,,,,,,,,,,,.,,, I ...........................................................................52
9. REMOVAL, STORAGE AND TRANSPORTATION ............................................................................... 54
9-1 Removal .To be conducted by a technician only -...................................................................................... 54
9-2 Storage ........................................................................................................................................................ 56
9-3 Transportation ............................................................................................................................................. 56
10. DISCARDING THE PRODUCT ........................................................................................................... 57
11. PARTS LIST .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .....I.
58
KIT COMPONENT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . ..~......................................................................................... 59
m : Directions to follow when installing the product in a JAMMA STANDARD conforming cabinet.
m : Directions to follow when installing the product in a JAMMA VIDEO STANDARD (JVS) conforming cabinet.

2. SPECIFICATIONS
Item
Compatibility
Weight
Input power
Operating environ-
ment
Connectable cabinet
Monitor orientation
and monitor signal
Cammunicalion-
linked setup
Control panel of
cabinet
Method of installation
in cabinet
-
IDescription
JAMMA STANDARD Y (JAMMA PC board kit (optional) is required)
JAMMA VIDEO STANDARD (JVS)2
W320 mm x D315 mm xHliO mm
5.8 kg .
(When connected to JAMMA STANDARD connectors]
+5V *5% (7 A minimum) and +12V i5% (2 A minimum)
(When connected to JAMMA VIDEO STANDARD connectors]
+5V f5% (7 A minimum) and +12V f5% (2 A minimum)
Indoor use only
Temperature: 5 to 45°C humidity: IO to 85% (no dew condensation)
JAMMA STANDARD conforming cabinet (JAMMA PC board kit (optional) is required)
JAMMA VIDEO STANDARD (JVS) conforming cabinet
Monitor orientation: Horizontally
Horizontal synchmnization frequency: 15.75 kHz (factory setting), can be changed to 31.5 kHz’
Scan fly-back line type:
[when set to 15.75 kHz] Non-interlace (factory setting), can be changed to interlace”
[when set to 31.5 kHz] Non-interlace (ftxed)
RGB output level: 0.7 Vp-p
l Note that the RGB output level is as follows when JAMMA PC board kit (optional) is
installed:
Can be switched: J.OVp-p (factory setting) /0.7Vp-p (5)
Synchronizing signal: Can be switched between Composite (factory setting) I Seperate
Vertical synchmnization frequency: 60.0 Hz
Competition game possible with one PC board when two JAMMA VIDEO STANDARD (JVS) confor
ing cabinets are connected by a cable.
[Pair control panel (for two-person play with single cabinet)]
l a-direction lever 1x2
*Button switch 4x2
* Start switch 1x2
[Single control panel (for communication-linked setup with two cabinets connected with cable)]
For each cabinet
- E-direction lever 1
- Button switch 4
l Start switch 1
According to the operation manual of the cabinet
‘1 JAMMA STANDARD (JS)
Standards established by Japan Amusement Machinery Manufacturers Association (JAMMA) in 1986 for edge Conne-33~ Of video
gamePC boards.
+2 JAMMA VIDEO STANDARD (JVS)
Standards established by Japan Amusement Machinery Manufacturers Association (JAMMA) in 1996 for connection between video
game PC boards and peripheral devices.
‘3 Regarding Ihe switching of the horiiontal synchronization frequency, refer to’(l) Option switches’ In ‘6-1-l Adjustment switches
and knob” on page 29.
‘4 Regarding lhe switching of non-interlace and inletlace, refer to’6-24 lNTERLACE CHECK on page 37.
‘5 Seep. 29 “6-l-l Adjustment switches, knobs (1) Option Switch’ to switch RGS output level.
6

3. CHECKING THE PACKAGE CONTENT
The product package contains the following parts when shipped.
l Check to make sure all the parts listed below are included in the product
m package.
l If any parts are missing, contact your distributor.
0 Keep the box. The box is used to send the product for a repair.
NAI P/N
T403-09557-00
T405-10021-00
T405-10025-00
T405- 10026-00
VG50-06872-0 1
T450-10027-00
T450- 10025-00
T484-10029-00
T440-09994-00
T4JO-09995-00
T440-09995-o 1
T440-09996-00
T440-09997-00
T440-09998-00
T440-09999-00
T440- 10000-00
T440-10001-00
T440- 10002-00
T440-10003-00
VG44-07943-00
T450-10005-00
T45’0- 10006-00
T445-10010-00
VG05-06607-00
QTY
11
1
1
11
1
1
1 I
1
1
1
1
1
1
2
2
1
1
1
1
1
1
4
DESCRIPTION
Rack (B) Assy, Tekken 4, SYS 246
Dangle
JAMMA (B) pcb
Harness, Video Cable, I5P D-Sub, IMale-to-Male
Harness, Audio Cable. RCA Pair
Harness, Ribbon Cable, 20P Dual Row
Harness, DC Power. JST, VH Series
Disc, DVD
Decal, Marquee
Decal, Side Panel, Left
Decal, Side Panel, Right
Decal, Control Panel Overlay
Decal, Logo
Decal, Player 1
Decal, Player 2
Decal, Punch
Decal, Kick
Card, Game Instructions
Card, Move List
Label, Epileptic Warning
Harness, Kick Buttons
Harness, Right Speaker
Manual
PCB Mounting Feet w/screws
Items in addition to those listed above may be present in your kit. such as labels. decals.
harnesses, and a Namco Ltd manual. Put these aside as they will not be used in the
typical kit installation.
See page 59 in this manual for an illustration of components to be used in a typical kit
installation.
For parts, refer to P. 58 “11. Parts List.”
7

4. NAMES OF PARTS
DVD-ROM
drive
connector
R //
Video cable
“l.‘,‘“,, c.““llL
connectors Audio cable
connectors
STANDARD l/O cable
connector
boardPC
8

5. INSTALLATION AND CONNECTION
-To be conducted bv a technician onlv.
0Before installing and connecting the product, turn off the power switch on the cabinet
and unplug the power cord from the service outlet to prevent an electric shock.
l Do not install or connect the product outdoors. The product is designed for indoor
use only. Installation or connection of the product conducted outdoors can cause an
electrical shock or fire.
m
l Make sure the person conducting the installation or connection is not
charged with static electricity. Static electricity can cause a malfunction
or damage of this product.
0Do not perform a conductivity test using a tester. The internal voltage in a
tester can damage the ICs on the PC board and render the PC board
useless.
The product can be used with a JAMMA STANDARD or JAMMA VIDEO STANDARD (JVS) conforming
cabinet. However, the connection method varies depending on the type of the cabinet.
To install the product in a JAMMA STANDARD conforming cabinet, the JAMMA PC board kit (optional)
is required.
*Check the cabinet specification for compatibility by referring to P. 6 “2. SPECIFICATIONS.”
Sections in the Operation Manual applicable to each STANDARD
Check the specification of the cabinet and read the sections described below according to the STAN-
DARD applicable to the cabinet.
0Connection to JAMMA STANDARD conforming cabinet:
Connect the PC board according to the directions in the operation manual supplied with the
JAMMA PC board kit (optional), then read the sections marked with EiI m on pages IO
through 12, and the sections marked withmon pages 15 through 20 of this Operation Manual.
l Connection to JAMMALIDEO STANDARD (JVS) conforming cabinet:
Read the sections marked withmlm on pages 10 through 12, and the sections marked with
m on pages 22 thmugh 24 of this Operation Manual.
l The product cannot be connected to a JAMMA VIDEO STANDARD (JVS) conforming
cabinet installed with the JAMMA PC board kit (optional).

5. INSTALLATION AND CONNECTION -To be conducted by a technician only -
5-I Preparation for installation m/5W
Prepare the following tools and materials for the installation of the product.
Item to be prepared
Operation manual of the
cabinet
Soldering iron, or crimping
tool and crimp-style termi-
nals
Heat-shrink insulation tube
and dryer for heating
Insulation tape
Description
Check the handling directions for the
cabinet.
To connect wires to microswitch.
May not be needed in some cases. Refer
to pertinent pages.
To insulate wire connections.
May not be needed in some cases. Refer
to pertinent pages.
To insulate ends of unused wires and
connectors.
Unnecessary when the product is installed
in a JAMMA STANDARD conforming
cabinet equipped with two speakers
(stereo-type).
Page]
--I
Section 5-4-l BB
(P. 15)
Section 5-4-3 W
(P. 17)
Section 5-4-4 EB
(P. 19)
Section 5-4-l EI
(P. 15)
Section 5-4-3 B
(P. 17)
A
Section 5-4-4 m
(P. 19)
Section 5-5-Z 5EI
(P. 23)
40

5. INSTALLATION AND CONNECTION -To be conducted by a technician only -
5-2 Installation of PC board and JAMMA (6) PC board to mount-
ing plate of JAMMA STANDARD conforming cabinet E+I
0
R
To install the product in a JAMMA STANDARD conforming cabinet, mount the PC
board andJAMMA (B) PC board on the mounting plate by following the procedures
below.
Turn off the power switch on the cabinet, and unplug the power cord from the
service outlet.
By following the directions for PC board installation in the operation manual of the
cabinet, open the cover of the PC board compartment and take out the PC board
mounting plate.
Mounting plate
m If another PC board has been installed, remove the PC board by following the
directions in the operation manual of the cabinet.
11

5. INSTALLATION AND CONNECTION -To be conducted by a technician only.
qUsing the supplied mounting screws (Phillips tapping bind (A) x 4), install the PC
board and JAMMA (6) PC board at locations on the mounting plate where the
installed PC boards do not hinder the reinstallation of the mounting‘plate.
Mounting holes
(4 locations)
\\\
Mounting holes (4 locations)
JAMMA (6) PC board
m
lIf the cabinet is dirty, clean with a vacuum cleaner.
lTo install the PC board and JAMMA(6) PC board, be sure to use the screws
(Phillips tapping bind (A) x 4) provided with this product and in the JAMMA
(B) PC board kit (optional).
lFor the connection of connectors, refer to the instructions provided with
the JAMMA (6) PC board kit (optional).
12

5. INSTALLATION AND CONNECTION -To be conducted by a technician only -
5-3 Installation of PC board to mounting plate of JAMMA VIDEO
STANDARD (JVS) conforming cabinet w
D
q
Install the PC board to the mounting plate by following the procedures below.
Turn off the power switch on the cabinet, and unplug the power cord from the
service outlet.
By following the directions for PC board installation in the operation manual of the
cabinet, open the cover of the PC board compartment and take out the PC board
mountingplate.
When two cabinets are used for a communication-linked setup, the PC board can
be installed in either unit.
Mounting plate -
Namco CYBERLEAD (example)
m If another PC board has been installed, remove the PC board by following the
directions in the operation manual of the cabinet.
13

5. INSTALLATION AND CONNECTION -To he conducted by a technician only -
m Using the supplied mounting screws (Phillips tapping bind (A) x4) install the PC
board at a location on the mounting plate where the installed PC board does not
hinder the reinstallation of the mounting plate.
Mounting holes
(4 locations)
0If the cabinet is dirty, clean with a vacuum cleaner.
l To install the PC board, be sure to use the screws (Phillips tapping bind
(A) x 4) provided with the product.
14

5. INSTALLATION AND CONNECTION - To be conducted by a technician only.
5-4 Connection to JAMMA STANDARD conforming cabinet BB
5-4-l Checking the JAMMA edge connector m
To connect the product to a JAMMA STANDARD conforming cabinet, use the JAMMA
edge connector provided with the cabinet.
0 Check to make sure the terminal numbers of the JAMMA edge connector corre-
spond with those in the JAMMA edge connector table below. If not, solder or use
crimp-style terminals to connect wires as indicated in the table.
mi
0Cover connections with heat-shrink insulation tubes to prevent shorting.
0Do not connect wires to the terminals with no indication in the table.
Connection of a wire to those terminals can cause the PC board to
malfunction.
JAMMA edge connector (56.pin, 3.96-mm pitch)
I
Soldered surface
1 Terminalsurface 1 Component surface
1
GND A 11 GND
GND 1B 1
2
GND
+5v
+5V IcI
3 I
l W 1A
lea (GREEN) 1N 112 1Video (RED)
Viden (SYNC\ I P I 13 I
t
..___
I-“‘-,
I I Video (BLU;)
Sprvire cwitrh 1 R 1IA 1Video fGNDI
*..,-- -....-..
Coin switch 2
P2 Start switch
15
16
17
Test switch
Coin s
PI Statwitch 1 t switch
p7 I 1,111 II IPi
. LI.11 \“, ,IvIIA I
I.
._
Pl Lever UP)
P2 I-ever (DOWN) 1w 119 1PI Lever (DOW
‘V
P7 I ever II FFT\
PI Leve
- --.-. \--’ .I
I x I 20 I
I!r’(LEFT)
p2 I over /RIGHT\
_“.~. ,...-.,.,
I Y 171 I
I
-.
Pl Lever IRIGHT)
P2 t Sutton switch 1 I 2I 22 IPI Button
switcl fll
P2 Button switch 2 a
)23 1Pl Button switch 2
1b 124 1
C 125 1
GND
GND
d
26
e 27 GND
f28 GND

5. INSTALLATION AND CONNECTION. To be conducted by a technician only.
m Check the voltage of power supplied from the cabinet to be connected with the
JAMMA edge connector and the voltage of power supplied to the coin counter in
the cabinet.
0The power supplied from the cabinet connected to the JAMMA edge connector must
comply with the following specifications.
l +5 V power supply -allowed voltage fluctuation G%, current: 7 A or higher
I
: +I? V pawefsuq@y - ahwed voltage fluctuatton &%;curront:K2 A or higher
Use of non-conforming power supply can cause a fire.
0Use +lZV or t5V power supply for the coin counter in the cabinet. Higher
voltaae can cause the PC board to malfunction.
If thevoltage is low, the LED on the JAMMA PC board blinks. When the
LED blinks, check the power supply voltage.
5-4-2 Checking the extension harness W
When connecting the product to a JAMMA STANDARD conforming cabinet, use
the extension switch harness and extension stereo harness provided in the
JAMMA PC board kit.
Check to make sure the terminal numbers of the extension switch harness and
extension stereo harnesses correspond with those in the table below.
(Note) The extension switch harness and extension stereo harness are not used
when the product is installed in a JAMMA VIDEO STANDARD (JVS) con-
forming cabinet.
m
l Do not connect wires to the terminals with no indication In the table.
Connection of a wire to those terminals can cause the PC board to
malfunction.
Extension switch harness (EHOP) Extension stereo harness
(El4P)
16