NAPCO iBridgeVideo IBV-CHIME User manual

NAPCO iBridgeVideo IBV-CHIME Installation Guide 1
Description
The iBridgeVideo®IBV-CHIME provides a wireless chime
for homes without an existing wired chime. Used with the
IBV-DBELL Video Doorbell, the IBV-CHIME plugs into an
indoor electrical outlet and plays a selected tone when your
IBV-DBELL button is pressed. The IBV-CHIME also pro-
vides the ability to add a chime sounder to additional rooms
or floors distant from the primary doorbell sounder (multiple
IBV-CHIMEs can be added to a single IBV-DBELL).
Use this guide after you install and activate your IBV-DBELL.
Both are connected to Wi-Fi using the iBridgeVideo App
(Android or iOS). The IBV-DBELL provides:
 Multiple ring tones
 Volume control
 Mobile iBridgeVideo App (Android or iOS)
 Easy Wi-Fi installation
For more information about the iBridgeVideo IBV-DBELL,
see WI2304 (installation instructions) and OI411 (User's
Guide).
Quick Install Summary:
a. Wire and configure the doorbell.
b. Launch the iBridgeVideo app and log in.
c. Use the iBridgeVideo app to add and configure the IBV-
CHIME.
IBV-CHIME Enrollment Using the App
The steps below display Android screen images (iOS devic-
es are similar). Perform the following procedure only after
the IBV-DBELL(s) has been activated at
www.NapcoComNet.com and enrolled in the iBridgeVideo
or iBridge app. In addition, the IBV-CHIME must be
plugged into a wall outlet (as detailed above) and its cyan
LED must be flashing continuously. Proceed as follows:
1. With your smart device connected to the local Wi-Fi
network, launch the iBridgeVideo app.
2. Type a Username (use your full email address) and
Password and tap Login.
3. Tap "+" to add the IBV-CHIME.
4. Scan the QR code located on the top of the IBV-
CHIME, then tap OK. If you have trouble scanning
the code, tap Manually enter SN and type the serial
number.
5. Tap Next to connect the IBV-CHIME to the Wi-Fi net-
work.
NAPCO iBridgeVideo®IBV-CHIME
Doorbell Chime Accessory
Installation Guide
WI2334LF 7/19
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, [phone]
For Technical Service, [phone] or visit us at
http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC © NAPCO 2019

2NAPCO iBridgeVideo IBV-CHIME Installation Guide
6. Enable your IBV-CHIME "hotspot": With the LED on
the front of the IBV-CHIME flashing (indicating it is
not yet connected to a network), press and hold the
"Hotspot" button on the front of your IBV-CHIME for 5
seconds, then release (listen for 3 beeps and its LED
will begin to flash fast). Tap Next.
7. The screen shown below appears, allowing you to con-
nect your smart device to your IBV-CHIME.
Temporarily go into your smart device "Wi-Fi Settings"
and select the IBV-CHIME from the Wi-Fi list, as shown
in the following example image:
Then return to the app (the screen shown under step 7)
and tap Next.
8. Tap to select the 2.4GHz Wi-Fi network you wish to con-
nect to your IBV-CHIME.
9. Type the SSID Password of the selected network (to
view the password characters, tap the "eye" icon to the
right). Optional: To allow the app "remember" the pass-
word, check Save password. When finished, tap Con-
nect (the LED start flashing).
Important: Be sure the password is typed correctly
or the IBV-CHIME will not connect to the network.
You can always select another network by tapping Se-
lect other network; if the Password entry field does
not appear, tap Select other network and re-enter.
10. Wait for the Wi-Fi connection process to finish (see
image below). If the connection is successful, the LED
on the face of the IBV-CHIME will stop flashing and
will turn on solid cyan. Tap Yes to continue. If the at-
tempted connection is unsuccessful, try again by tap-
ping Add Again. Note: It may take up to a minute to
establish a connection.
If IBV-CHIME Does Not
Connect (LED keeps
Flashing)
Check the Wi-Fi signal
strength from the IBV-
CHIME location using the
smart device to ensure there
is sufficient Wi-Fi signal
strength (3 bars or more is
recommended). Also verify
the Wi-Fi password entered.
If needed, tap the Add Again
button to repeat steps 6-11.
Chime-4H0448
Chime-4H0448

NAPCO iBridgeVideo IBV-CHIME Installation Guide 3
Tap to select a tone, then click the Save icon.
Note: This Link Chime screen also allows you to
cancel the connection between the doorbell and the
chime (tap Cancel Link).
Device Settings
Tap Me > My Devices, then tap the IBV-CHIME to open
the Device Info screen. The selections are as follows:
 Volume Setup - Tap to adjust the chime sound level.
 Link Doorbell - Tap to display the name of the IBV-
DBELL doorbell to which the IBV-CHIME is linked.
 Cloud Upgrade - Tap to upgrade the IBV-CHIME
firmware (when available).
 Wi-Fi Config - Tap to change your Wi-Fi network.
 Delete Device - Tap to delete the selected device
from the iBridgeVideo app.
Reset to Factory Default Settings
Insert a small wire into the Reset Button hole (see "IBV-
CHIME Parts" on page 4 for location). Press and hold
the button for 10 seconds, then release.
Cyan LED Status Indications
When the chime is powered and operating normally, the
cyan LED remains on solid. Other LED indications are:
Cyan Solid.......................... Connected
Cyan Flashing .................... No Network Connection
Cyan Rapid Flashing.......... Hot spot enabled
Specifications
Audio
Audio Output ................. Built-in loudspeaker
Ring Tone ..................... Multiple ring tones available
Operation Mode
Reset Button ................. 1
Indicator Light................ 1
Network
Wi-Fi.............................. IEEE802.11b/g/n
General
Installation..................... Surface
Voltage.......................... 90 - 240VAC
Working Temperature ... ‒10°C - +50°C (+14°F - 122°F)
Relative Humidity .......... 20% - 95% RH
Dimensions ................... 99 x52 x33.7 mm (3.9 x2.04 x1.33 in.)
Weight........................... 0.3 Kg (10.6 oz.)
11. Link your IBV-CHIME to sound when the IBV-
DBELL button is pressed, tap the "chain
link" icon located above the doorbell camera
image:
12. Tap + New Link.
13. Select the IBV-CHIME from the list and tap Save.
Note: The IBV-CHIME must be enrolled before it
will appear in the list. If you have an existing wired
doorbell chime mechanism (mechanical or electronic),
tap Link Third Party Chime at the bottom of the screen:
Change Tone Type
Select from multiple available ring tones by tapping
the "chain link" icon located above the doorbell
camera image (see image in step 11, above).
In the Link Chime screen, tap Tone setup:
4H0448

4NAPCO iBridgeVideo IBV-CHIME Installation Guide
NAPCO LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products
to be free from manufacturing defects in materials and workmanship for
twelve months following the date of manufacture. NAPCO will, within
said period, at its option, repair or replace any product failing to operate
correctly without charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof,
which has been repaired by others, improperly installed, improperly
used, abused, altered, damaged, subjected to acts of God, or on which
any serial numbers have been altered, defaced or removed. Seller will
not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
THERE IS NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN
LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART
OF NAPCO.
Any action for breach of warranty, including but not limited to any
implied warranty of merchantability, must be brought within the six
months following the end of the warranty period. IN NO CASE SHALL
NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR
DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR
FAULT.
In case of defect, contact the security professional who installed and
maintains your security system. In order to exercise the warranty, the
product must be returned by the security professional, shipping costs
prepaid and insured to NAPCO. After repair or replacement, NAPCO
assumes the cost of returning products under warranty. NAPCO shall
have no obligation under this warranty, or otherwise, if the product has
been repaired by others, improperly installed, improperly used, abused,
altered, damaged, subjected to accident, nuisance, flood, fire or acts of
God, or on which any serial numbers have been altered, defaced or
removed. NAPCO will not be responsible for any dismantling,
reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and
any prior agreements or representations, whether oral or written, are
either merged herein or are expressly cancelled. NAPCO neither
assumes, nor authorizes any other person purporting to act on its behalf
to modify, to change, or to assume for it, any other warranty or liability
concerning its products.
In no event shall NAPCO be liable for an amount in excess of
NAPCO's original selling price of the product, for any loss or damage,
whether direct, indirect, incidental, consequential, or otherwise arising
out of any failure of the product. Seller's warranty, as hereinabove set
forth, shall not be enlarged, diminished or affected by and no obligation
or liability shall arise or grow out of Seller's rendering of technical advice
or service in connection with Buyer's order of the goods furnished
hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE
COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any
or all of the following; criminal tampering, electrical or communications
disruption, it is possible for the system to fail to perform as expected.
NAPCO does not represent that the product/system may not be
compromised or circumvented; or that the product or system will prevent
any personal injury or property loss by burglary, robbery, fire or
otherwise; nor that the product or system will in all cases provide
adequate warning or protection. A properly installed and maintained
alarm may only reduce risk of burglary, robbery, fire or otherwise but it is
not insurance or a guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS
BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
Therefore, the installer should in turn advise the consumer to take any
and all precautions for his or her safety including, but not limited to,
fleeing the premises and calling police or fire department, in order to
mitigate the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's
family or employees, and limits its liability for any loss or damage
including incidental or consequential damages to NAPCO's original
selling price of the product regardless of the cause of such loss or
damage.
Some states do not allow limitations on how long an implied warranty
lasts or do not allow the exclusion or limitation of incidental or
consequential damages, or differentiate in their treatment of limitations of
liability for ordinary or gross negligence, so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
1
3
7
5
9
4
8
1. Speaker
2. Reset Button (recessed)
3. Hotspot Button
4. Indicator LED
5. QR Code (on top)
6. Wi-Fi MAC Address of Unit
7. Serial Number of Unit
8. Prong Release
9. Power Plug*
2
6
IBV-CHIME Parts
* USA 120VAC shown.