National Instruments NI-6589 User manual

NI-6589
2022-07-06

Contents
NI 6589 Getting Started Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FlexRIO Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Verifying the System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the NI 6589. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Confirming that Measurement & Automation Explorer (MAX) Recognizes the Device. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Panel and Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Component-Level Intellectual Property (CLIP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
NI 6589 CLIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Clocking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Worldwide Support and Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ni.com
2
NI-6589

NI 6589 Getting Started Guide
Note Before you begin, complete the soware and hardware installation
instructions in the getting started guide for your FlexRIO FPGA module or
Controller for FlexRIO.
The NI 6589 is a FlexRIO adapter module designed to work in conjunction with
FlexRIO FPGA modules and Controllers for FlexRIO.
The NI 6589 features 20 LVDS channels (16 data and 4 PFI), and sample rates up to
1 Gbit/s on LVDS channels
This document explains how to install and configure the NI 6589.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits are designed to provide reasonable protection against
harmful interference when the product is operated in the intended operational
electromagnetic environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory
rules.
Caution To ensure the specified EMC performance, operate this product
only with shielded cables and accessories.
© National Instruments 3
NI-6589

Caution To ensure the specified EMC performance, you must attach EMI
gaskets (NI part number 746228-01) to both sides of your NI 6589 before
using.
Caution To ensure the specified EMC performance, you must install PXI
EMC Filler Panels (NI part number 778700-01) in all open chassis slots.
FlexRIO Documentation
Document Location Description
Getting started guide
for your FlexRIO FPGA
module or Controller
for FlexRIO
Available from the Start menu and
at ni.com/manuals.
Contains installation instructions for
your FlexRIO system.
Specifications
document for your
FlexRIO FPGA module
or Controller for
FlexRIO
Available from the Start menu and
at ni.com/manuals.
Contains specifications for your
FlexRIO FPGA module or Controller
for FlexRIO.
Getting started guide
for your adapter
module
Available from the Start menu and
at ni.com/manuals.
Contains signal information,
examples, and CLIP details for your
adapter module.
Specifications
document for your
adapter module
Available from the Start menu and
at ni.com/manuals.
Contains specifications for your
adapter module.
LabVIEW FPGA
Module Help
Embedded in LabVIEW Help and
at ni.com/manuals.
Contains information about the basic
functionality of the LabVIEW FPGA
Module.
Real-Time Module
Help
Embedded in LabVIEW Help and
at ni.com/manuals.
Contains information about real-time
programming concepts, step-by-step
instructions for using LabVIEW with
the Real-Time Module, reference
information about Real-Time Module
VIs and functions, and information
about LabVIEW features on real-time
operating systems.
ni.com
4
NI-6589

Document Location Description
FlexRIO Help Available from the Start menu and
at ni.com/manuals.
Contains information about the FPGA
module front panel connectors and
I/O, controller for FlexRIO front panel
connectors and I/O, programming
instructions, and adapter module
component-level IP (CLIP).
FlexRIO Adapter
Module Development
Kit User Manual
Available from the Start menu at
Start » All Programs » National
Instruments » NI FlexRIO » NI
FlexRIO Adapter Module
Development Kit »
Documentation.
Contains information about how to
create custom adapter modules for
use with FlexRIO FPGA modules.
LabVIEW Examples Available in NI Example Finder. In
LabVIEW, click Help » Find
Examples » Hardware Input and
Output » FlexRIO.
Contains examples of how to run
FPGA VIs and Host VIs on your device.
IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA functions
and intellectual property to share.
FlexRIO product page Located at ni.com/flexrio. Contains product information and
data sheets for FlexRIO devices.
Table 1. FlexRIO Documentation Locations and Descriptions
Verifying the System Requirements
To use the FlexRIO Support instrument driver, your system must meet certain
requirements. For more information about minimum system requirements,
recommended system, and supported application development environments
(ADEs), refer to the FlexRIO Support Readme, which is available on the FlexRIO
Support soware DVD or online at ni.com/updates.
© National Instruments 5
NI-6589

Unpacking
Caution To prevent ESD from damaging the devices, ground yourself
using a grounding strap or by holding a grounded object, such as your
computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove each module from the package and inspect it for loose components
or any other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the devices in the antistatic package when they are not in use.
Preparing the Environment
Ensure that the environment you are using the NI 6589 in meets the following
specifications.
Operating temperature (IEC 60068-2-1, IEC 60068-2-2) 0 °C to 55 °C
Operating humidity (IEC 60068-2-56) 10% to 90% RH, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m at 25 °C ambient temperature
Indoor use only.
Note Refer to the NI 6589 Specifications at ni.com/manuals for complete
specifications.
ni.com
6
NI-6589

Caution Clean the hardware with a so, nonmetallic brush. Make sure
that the hardware is completely dry and free from contaminants before
returning it to service.
Installing the NI 6589
Refer to the getting started guide for your FlexRIO FPGA module or Controller for
FlexRIO for instructions about how to install your FlexRIO system, including the
NI 6589.
Confirming that Measurement & Automation Explorer (MAX)
Recognizes the Device
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which devices reside in the system and how they are
configured. MAX is automatically installed with FlexRIO Support.
1. Launch MAX by navigating to Start » All Programs » National Instruments » NI
MAX or by clicking the NI MAX desktop icon.
2. In the Configuration pane, double-click Devices and Interfaces to see the list
of installed devices. Installed devices appear under the name of their
associated chassis.
3. (PXI and PXI Express devices only) Expand your Chassis tree item. MAX lists all
devices installed in the chassis. Your default device names may vary.
Note If you do not see your hardware listed, press <F5> to refresh
the list of installed devices. If the device is still not listed, power o
the system, ensure the device is correctly installed, and restart.
4. (Controllers for FlexRIO only) Your device appears under the Remote Devices
section.
© National Instruments 7
NI-6589

Cables
Caution You must operate the NI 6589 with shielded cables and shielded
accessories to ensure compliance with the EMC requirements defined in
the NI 6589 Specifications. Do not use unshielded cables or accessories
unless they are installed in a shielded enclosure with properly designed
and shielded input/output ports and are connected to the NI 6589 using a
shielded cable. If unshielded cables or accessories are not properly
installed and shielded, the EMC specifications for the NI 6589 are no longer
guaranteed.
Use a shielded 50 Ω coaxial cable with an SMA plug end to connect to the PFI 0 and
CLOCK IN connectors on the NI 6589 front panel. Use the NI SHB12X-B12X shielded
cable (NI part number 192344-01) or the NI SHB12X-H3X24 dierential flying-lead
cable (NI part number 196236-1R5) to connect to the DDC connector. You can also
connect the NI SMA-2164 accessory to the NI 6589 through the SHB12X-B12X
shielded cable for testing and debugging.
Note If you design a custom cabling solution with the DDC connector
(779157-01) and SHB12X-B12X shielded cable (192344-01), the NI 6589
pinout is reversed at the end connector. For example, the signal shown on
pin 1 maps to pin 73 at the end connector.
The following NI cables and accessories are not properly shielded for EMC-
compliant use with the NI 6589:
■NI SMA-2164 accessory
■NI SHB12X-H3X24 dierential flying-lead cable
Note Whether you use NI cables and accessories or design your own,
terminate cables properly to avoid improper measurements caused by
signal reflections, overshoot, and undershoot.
ni.com
8
NI-6589

Accessories
The NI SMA-2164 test fixture is a breakout box for dierential signals. This fixture
provides an easy way to connect to other devices for testing and debugging.
The following figure shows how to connect the dierential DDC connector to the
NI SMA-2164, using the NI SHB12X-B12X cable. For more information about using
the NI SMA-2164, refer to the NI SMA-2164/2165 Test Fixture User Guide.
Figure 1. Connecting the NI SMA-2164 Accessory
1
2
NI PXI-1042
3
STROBE
CLK_LVPECL
+
+
IO_3
+
–
IO_7
IO_10
I
IO_6
IO_11
IO_13
MADE IN U.S.A.
IO_15
ASSY192533 A- 01
+ –
+
–
+
+
+
–
–
+
–
–
–
–
I O_ 12
–
–
+
+
–
+
IO_4
IO_5
IO_8
IO_2
IO_9
–
+
–
+
+
–
IO_1
+
–
–
+
+
PFI_3
CLK_LVDS
+
PFI_2
+
–
+ –
PFI_1
VOS
VOS
VOS
VOS
VOS
VOS
VOS
VOS
VOS
VOS
VOS
IO_0
VOS
VOS
–
+
S/N
–
VOS
VOS
–
VOS
VOS
VOS
VOS
VOS
VOS
61 70
40 49 19 31 10
73
64 67
52 55
58
43 46 34 37 22 25 28 13 16
1
4 7
1
VOS
NI SMA-2164
DIFFERENTIAL
DIGITAL I/O ACCESSORY
FOR PATENTS: NI.COM/PATENTS
© COPYRIGHT 2005
NI 6587
PFI 0
CLOCK IN
1 Gbps
LVDS
1. PXI/PXIe Chassis with an NI 6589R
2. NI SHB12-B12X Cable
3. NI SMA-2164
A flying lead cable, the NI SHB12X-H3X24, is also available for dierential signals.
This cable oers connectivity similar to that found on a typical logic analyzer, so you
can use it in logic analyzer-type applications. This cable is shown in the following
figure.
© National Instruments 9
NI-6589

Figure 2. NI SHB12X-H3X24 Flying Lead Cable
1
23
1. Leads (1 × 3 Header Receptacle)
2. DDC Connector
3. Removeable Sleeving
Custom Accessories
If you are creating a custom accessory to use with a DUT with a VHDCI DDC
connector, you can purchase the mating connector for the VHDCI cable from NI. For
more information about creating these custom accessories, refer to the Interfacing
to the NI Digital Waveform Generator/Analyzer using the VHDCI Connector
application note.
Visit ni.com/info and enter the Info Code rdinwa to download this note.
If you are designing a custom accessory to use with a device that uses an InfiniBand
connector, you can also purchase this connector from NI.
Note If you design a custom cabling solution with the DDC connector
(779157-01) and SHB12X-B12X shielded cable (192344-01), the NI 6589
pinout is reversed at the end connector. For example, the signal shown on
pin 1 maps to pin 73 at the end connector.
For more information about connecting I/O signals on your device, refer to the
NI 6589 Specifications.
ni.com
10
NI-6589