National ES4001 User manual

1 SCHEMATIC DIAGRAM 2
2 WIRING CONNECTION DIAGRAM 2
3 DISASSEMBLY / ASSEMBLY INSTRUCTIONS 3
©2000 Matsushita Electric Works Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
ES4001
4 TROUBLESHOOTING GUIDE 6
5 EXPLODED VIEW & REPLACEMENT PARTS LIST 8
Wet/Dry Rechargeable Shaver
SPECIFICATIONS
Power source AC100-120V/220-240V, 50-60Hz
(Automatic voltage conversion)
Power source (only for Korea) AC110-220V, 60Hz
Power consumption 25/30mA
Power consumption (only for Korea) 30mA
Motor voltage 1.2V DC
Charging time 8-hours
Weight 150g
Supplied accessories Soft case
Cleaning brush
CONTENTS
Page Page
ORDER NO. SD0004A33C3

1 SCHEMATIC DIAGRAM
2 WIRING CONNECTION DIAGRAM
2
ES4001

3.1. MAIN UNIT REPLACEMENT
Follow the procedure below to disassemble the main block.
1. Remove Cap, Foil frame and Inner blades.
2. Loosen the two bottom screws and remove the bottom
cover.
3. Take out the chassis block from housing by pushing the
base of chassis.
4. Remove the trimmer driving bar.
5. Loosen the two screws and lift the rubber retaining plate
away.
6. Remove the driving head water proof rubber.
7. Remove the blade holder block.
NOTE: When reassembling, replace the new waterproof
rubber.
3 DISASSEMBLY / ASSEMBLY INSTRUCTIONS
3
ES4001

3.2. BATTERY REPLACEMENT
To remove the battery, fix the top of battery terminal with the
flat and lifting up the battery pin.
3.3. MODULE REPLACEMENT
The module is soldered to the chassis at 3 points.
1. Unsolder the three connections to the chassis.
2. Remove the module from the two hooks of the chassis.
3.4. DRIVING HEADS INSTALLATION
(1) Install driving head A in the chassis (with the motor
assembled) after inserting the motor tip pin into the hole of
armature of driving head A.
4
ES4001

(2) Then, install driving head B in the assembly (1) above after
inserting driving head B axis into the hole of armature 2 of
the motor.
3.5. WATERPROOF RUBBER INSTALLATION
The waterproof rubber must be fitted the right way around.
Install as shown in figure by inserting firmly to the set position.
5
ES4001

4 TROUBLESHOOTING GUIDE
6
ES4001

NOTE: The charging current fluctuates depending on the space between charging adaptor and the coil.
Please follow the procedure below.
1. Put the coil and the bottom cover close together.
2. Put the bottom cover and the charging adaptor close together.
3. Measure the charging current between two lead wires.
7
ES4001

5 EXPLODED VIEW & REPLACEMENT PARTS LIST
5.1. EXPLODED VIEW
8
ES4001

5.2. REPLACEMENT PARTS LIST
NOTE:
*A=available as an optional accessory
*B=only available as set
*C=available individually
Ref. No. Part No. Part Name & Description Remarks Per Unit
1WES4001X7158 PROTECTIVE CAP (BG) 1
2WES9837E OUTER FOIL 1
3WES4001S0047 OUTER FOIL FRAME (BG) 1
4WES9850E INNER BLADE 1
5WES762L9707 SCREW *B 2
6WES4001L0207 RETAINING PLATE (BG) 1
7WES727L0327 WATER-PROOF RUBBER SET (BG) 1
8WES4001H0007 BLADE MOUNTING BASE (BG) 1
9WES4001S3160 HOUSING (BG) 1
9WES4001S3161 HOUSING only for TAIWAN (BG) 1
9WES4001S3162 HOUSING only for HONG KONG SINGAPORE and UAE (BG) 1
10 WES4001H3207 SWITCH HANDLE (BG) 1
11 WES4001J3967 SWITCH PLATE (BG) 1
12 WES4001H0367 LOCK BUTTON (BG) 1
13 WES4001L1667 SWITCH CAM (BG) 1
14 WES663L0977 O-RING (BG) 1
15 WES4001H3267 LOCK RELEAS E BUTTON (BG) 1
16 WES4001L0177 SPRING FOR RELEASE BUTTON (BG) 1
17 WES4001K1507 TRIMMER (BG) 1
18 WES4001L2127 MODULE (BG) 1
19 WES4001L0777 CHASSIS (BG) 1
20 WES4001L0057 CONTACT PLATE (BG) 1
21 WES4001L1677 SWITCH CAM LEVER (BG) 1
22 WES727L1247 DRIVING HEAD A (BG) 1
23 WES727L1257 DRIVING HEAD B (BG) 1
24 WES4001L1087 TRIMMER DRIVING BAR (BG) 1
25 WES727L1007 MOTOR (BG) 1
26 WES366L2509 RECHARGEABLE BATTERY Ni-Mh (BG) 1
27 WES4001H3847 BOTTOM COVER (BG) 1
28 WES762L6007 SCREW *C 2
29 WES4001S3040 BODY BLOCK (BG) 1
29 WES4001S3041 BODY BLOCK only for TAIWAN (BG) 1
29 WES4001S3042 BODY BLOCK only for HONG KONG SINGAPORE and UAE (BG) 1
30 WES4001H7662 CHARGING ADAPTOR A-2 PLUG (BG) 1
30 WES4001H7663 CHARGING ADAPTOR C-2 PLUG (BG) 1
30 WES4001H7674 CHARGING ADAPTOR only for HONG KONG SINGAPORE and UAE (BG) 1
30 WES4001H7671 CHARGING ADAPTOR KOREAN PLUG (BG) 1
31 WES663H7667 WALL MOUNT 1
32 WES4001K7007 SOFT CASE (BG) 1
33 WES861B7057 CLEANING BRUSH 1
-WES4001S8012 INDIVIDUAL BOX (BG) 1
-WES4001S8013 INDIVIDUAL BOX only for TAIWAN (BG) 1
-WES4001S8111 OPERATING INSTRUCTIONS (BG) 1
9
ES4001
Printed in JAPAN