NCR 7772-K475 User manual

Kit Instructions
High Mount XL10 Customer Display Bracket, CX
7772-K475
Issue A

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,
and firmware become available. NCR, therefore, reserves the right to change specifications without prior
notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,
consult with your NCR representative or NCR office for information that is applicable and current.
Copyright © 2021
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved
Revision Record
Issue Date Remarks
ADec 2021 First Issue

High Mount XL10 Customer Display Bracket, CX
This kit provides a Bracket to Mount the XL10 Customer Display on the CX head.
Kit Contents
Item Part Number Description
1 497-0531229 Bracket Assembly, XL10 Display, High Mount, CX
2 006-8627600 Screw, M4x8, Phillips, Cross Recessed Pan Head
Machine Screw with External Tooth Lock Washer,
Black, Zinc
3 497-0529413 Cable, USBC, 10” Customer Display, 506mm
4 497-0531570 Cable Cover, Cast, Black
5 497-0531574 4:3 Cable Cover, Cast
6 497-0480152 Screw, M3x6mm, Machine, Phillips, Pan Head
7 006-8616073 Cable Tie, 2.5mm width, 100mm length

2 High Mount XL10 Customer Display Bracket, CX
Installation Procedure
Warning: Disconnect the AC power cord from the AC outlet and wait 30 seconds
before servicing the terminal.
1. Lay the Display face down on a flat surface.
Note: Always use a soft material (cloth, foam) to protect the display screen when
placing the terminal face down.
2. Remove the Cable Cover.
a. Remove the two (2) screws that secure the Cable Cover to the Back Cover.
b. Rotate and unhook the Cable Cover from the Back Cover.

High Mount XL10 Customer Display Bracket, CX 3
3. Connect the USB-CCable to the CX7 Display and tighten the thumbscrew.
Note: For clarity, the Neck is not shown in the illustration below and in the
succeeding illustrations.
4. Install the new Cable Cover. The new Cable Cover has a hole on the side to allow
cable routing.
a. Hook the bottom of the Cable Cover to the Back Cover, then rotate the Cable
Cover into place.
b. Secure the Cable Cover with two (2) screws.

4 High Mount XL10 Customer Display Bracket, CX
5. Partially install two (2) screws on the back of the CX7 Display in the location shown.
6. Hook the Bracket on the partially installed screws. Ensure the Cable is routed as
shown.

High Mount XL10 Customer Display Bracket, CX 5
7. Tighten the two (2) partially installed screws and install two (2) screws on the bottom
of the Bracket.
8. Connect the other end of the Cable to the back of the XL10 Customer Display and
tighten the thumbscrew.

6 High Mount XL10 Customer Display Bracket, CX
9. Secure the Cable on the side of the bridge lance using a cable tie as shown.
10. Install the XL10 Customer Display on the Bracket (4 screws). Ensure the Cable is
routed through the gap in the Bracket as shown.

High Mount XL10 Customer Display Bracket, CX 7
11. Pivot the XL10 Customer Display into position.