Nomadic Display Rolluxe Case User manual

Rolluxe Case top serves as a built-in
step stool to facilitate hanging and
adjusting lights or graphics.
Revised: March 27, 2014 North America: 800.732.9395 Europe: +353.98.66011
We recommend that you assemble and repack your display
prior to your first event. It is important to follow each step in
the order indicated. If you need additional assistance or have
any questions, please call your nearest Nomadic LifeLine:
North America: Ireland/Europe:
800.732.9395 + 353.1.208.7261
United Kingdom:
07699 734215
CONGRATULATIONS!
Like thousands of Nomadic Display owners around the world, you now own the
highest quality portable/modular display. Your Nomadic Instand® is specially
designed to give you the ultimate in versatility. Classic (curved) and Plus (straight)
frame systems fully integrate to meet your growing exhibit demands. And your
100% satisfaction is guaranteed by Nomadic.
The “No Questions Asked” Lifetime Warranty
Your Instand frame is guaranteed for life. If it ever fails to
function — for any reason — Nomadic Display will repair it
free of charge for as long as you own it. Be sure to complete
and return the enclosed warranty card immediately.
Made by Nomadic Display
Superior in design and strength, your Nomadic Display is built in Nomadic’s own
manufacturing plants in the U.S. and Ireland. We use only premium grade materials
and take pride in maintaining the highest standards of craftsmanship. Your display
is delivered to you packed for maximum protection and quick assembly.
Nomadic Cares, Please Recycle
All Nomadic aluminum frames and cases can be recycled.
Proper Care & Maintenance of your Nomadic Display
• Store display upright at room temperature
• Do not subject to extreme heat or cold
• Do not leave display in direct sunlight or trunk of auto
• Return display to room temperature before handling
• Avoid extreme bending of Panels or permanent creasing will occur
• Use fabric brush to remove dust from FabriColor Panels
REMEMBER –
Read the complete
instructions about your
Instand product before
assembling. If you need
additional assistance or have
any questions, please call the
nearest Nomadic LifeLine.
Setting Up Your Display
®

1
2
3
Revised: May 18, 2010 North America: 800.732.9395 Europe: +353.98.66011
Unfold connected strut insuring magnets
are facing the same direction...
Attach lights to top of struts. Swivel
fixtures to adjust position. Run cord
behind display.
…and connect bottom two sections by
joining as illustrated.
Rotate top section of strut up and slide
down onto top stud.
Slide bottom of connected strut onto
the red stud at the bottom of the frame.
Snap next two connectors onto studs
on frame.
Bow endcaps and lift onto studs atop
both sides of frame. For hinged panels
hook one side then the other. Slide hands
along length of panel to bond magnets.
Hang all top panels and full size panels
first. Lift onto studs atop frame. Hook
one side then the other. Gradually release
downward to bond magnets.
Setting Up Your Display
Place frame with red studs facing front. Grasp two top center hubs and lift
frame open to shoulder height. Handle
frame at hubs only.
Press front and back hubs in the center of
the frame until Instand locks into position.
(Front and back hubs do not meet.) *

300lbs
136kg
To use built-in
step stool
To remove top and set a new combination
To close and move Rolluxe case
Rolluxe Case
REMEMBER-
Write your personalized combination down for your records and
provide it to your I & D company prior to shipping the display.
To open lid set your combination at “000”.
To set a new combination...
Rolluxe Case top serves as a built-in step
stool to facilitate hanging graphics.
Use a hard object to push the silver
change lever in towards the center of the
lock and then up towards the lid.
Do not wear high heels on step stool.
Return the silver change lever to its
original position. Your new combination is
now set.
...look at the back of the lock between
the latch and the case to locate the silver
change lever.
Make sure that step stool is on a level floor.
Set your new combination by turning the
dials downward on the front of the lock
Step surface may be slippery when wet.
Align handle with wheels, snap and lock
exterior latches. Scroll down the
combination locks.
Press red button to release side latches
and remove the top. Note: You may want
to change all combinations to match.
Do not place more than 300 lbs / 136 kg
on step stool.
Grip top handle with one hand and the
retractable handle with the other to lift case.
Remember to always bend your knees.
Revised: May 18, 2010 North America: 800.732.9395 Europe: +353.98.66011

Revised: November 04, 2011 North America: 800.732.9395 Europe: +353.98.66011
Dismantling Instructions
Switch off and unplug all lights.
Allow them to cool.
Gently remove and roll up all
surface graphics.
Roll individual Ribbed Panels fabric side
out. Roll Frontrunner End Caps fabric
side out.
Roll individual Smooth fabric or
Graphic Panels with liners in between
and roll fabric/image side out. Repeat
same for End Caps.
Put rolled panels into case one at a time and
one inside another. The top stiffener of one
panel should touch the bottom stiffener of
the previous panel. Stack Endcaps two high.
Lift top section of strut up. rotate down.
Remove all lights.
Twist strut to unsnap from frame. Lift bottom of strut off bottom stud.
Pull strut sections apart. Fold lengthwise ensuring that pegs at
top of strut face inward. Place connected
struts upside down in case.
Push on middle hub at back of frame while
pushing on corresponding front hub. Instand
will sink to the floor. Handle frame at hubs.
Remove all accessories
Remove and roll up
FabriColor and
Photomural Strips:
Remove Magnetic Struts
and Collapse Frames:

Revised: May 18, 2010 North America: 800.732.9395 Europe: +353.98.66011
Repeat on opposite side.
Place the plastic top shelf half with
exposed magnetic lip on top of the case.
Attach fabric end cap by starting at
corner…
Place the second plastic top shelf half
on top of the cases ensuring magnets
are aligned and engaged.
Attach front fabric panel to Velcro at top
and bottom. Form a straight line with
magnets on front panel before attaching
end caps.
Repeat with last end cap. Counter load is
100 lbs / 46 kg; a heavier load may cause
failure.
…wrap end cap along top edge then
bottom edge. Slide hands along length of
edge of end cap to bond magnets.
Setting Up Your
Rolluxe Counter
Place one wheel stop on the floor and
roll the cases on to it.
Place second wheel stop on the floor
under the opposite wheels.
Rolluxe BRolluxe A
Rolluxe B
Rolluxe A
Rolluxe BRolluxe A