NCR 7360-K433 Manual

Kit Instructions
PIN Pad Mount (Verifone M400)
7360-K433
Issue A

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR FastLane SelfServ™ Checkout is a trademark of NCR Corporation in the
United States and/or other countries. Other product names mentioned in this publication may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms
and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a
customer’s installed software exactly. Therefore, before using this document, consult with your NCR representative or NCR office
for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.
Please use the link below to send your comments.
Email: [e-mail]
Copyright © 2020
By NCR Corporation
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved

iii
Revision Record
Issue Date Remarks
ADec 2020 First Issue

PIN Pad Mount (Verifone M400)
This publication provides procedures for installing a PIN Pad Mount for a Verifone
M400 device on an NCRFastLane SelfServ™ Checkout (7360) unit.
Note: The Verifone M400 PIN Pad is supplied by the customer.
Kit Contents
Part Number Description
497-0528980 7360-K433 PIN Pad Mount (Verifone M400) Kit
* 497-0423108 Instructions - Kit (Reference Sheet)
* Items marked with an asterisk are not called out on the image.

2 PIN Pad Mount (Verifone M400)
Installation Procedures
Installing the PIN Pad Mount involves the following procedures:
•Installation Procedures above.
•Installing PIN Pad Mount on page6.
•Installing Verifone M400 PIN Pad on page13.
Note: The Verifone M400 PIN Pad is not included in the 7360-K433 PIN Pad Mount
(Verifone P400) Kit. For more information, contact an NCRCustomer Service
Representative.

PIN Pad Mount (Verifone M400) 3
Removing Existing PIN Pad Mount
Depending on the SelfServ Checkout unit, refer to the following:
•Full Recycling (Fixed/Convertible) Unit on the next page.
•Credit/Debit Only Unit on page5.

4 PIN Pad Mount (Verifone M400)
Full Recycling (Fixed/Convertible) Unit
To remove the existing PIN Pad Mount, follow these steps:
1. Remove the Allen key securing the PIN Pad Mount to the PIN Pad Arm.
2. Remove the PIN Pad Mount from the PIN Pad Arm, as shown in the images below.

PIN Pad Mount (Verifone M400) 5
Credit/Debit Only Unit
To remove the existing PIN Pad Mount, follow these steps:
1. Remove the Allen key securing the PIN Pad Mount to the PIN Pad Arm.
2. Remove the PIN Pad Mount from the PIN Pad Arm, as shown in the images below.

6 PIN Pad Mount (Verifone M400)
Installing PIN Pad Mount
Depending on the SelfServ Checkout unit, refer to the following procedures:
•Installing PIN Pad Mount above.
•Credit/Debit Only Unit on page9.

PIN Pad Mount (Verifone M400) 7
Full Recycling (Fixed/Convertible) Unit
To install the PIN Pad Mount on a Fixed or Convertible unit, follow these steps:
1. Attach the PIN Pad Mount to the PIN Pad Arm.
2. Position the PIN Pad Mount so that its edge is approximately parallel with the Pivot
Arm Surface.