NEFF S3443B1 User manual

Summary of instructions for dishwasher
Brief and handy:
everything your dishwasher
needs.
Before using for the first
time, read the installation
and operating instructions!
Select programme Off we go
Switch off the appliance Everythingo.k.
Fill with rinse aid
Fill with detergent
Fill with salt
Turn on the tap Water ready
When the “programme end” display illumi-
nates, switch off the main switch. Turn off
the tap.
Switch on the appliance
Close the door. Press the On/Off switch,
the last selected programme starts automatically.
5600 052 330    
en
Setting the water softening system * Quickly sorted
Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Read off the setting
Setting°dH °fH °Clarke mmol/l
and then select a setting
– Hold down programme button Band switch on the main
switch, then release the buttons. The . display flashes and
buttons Aand Billuminate (water hardness setting was set
to 2 at the factory).
– Each time button Bis depressed, the setting increases by
one (0-3). If buttons A, Band Cilluminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
0
1
2
3
Reset
A B C
22–35
0–6
7–16
17–21
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
9–20
0–11
12–29
30–37
38–60
0–8
21–26
27–44
Dissolves limescale (not required for set value 0!)
Unscrew
the lid. Only before using
the dishwasher
for the first time
pour approx. 1 l /
2 pt water into the
salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2. Pour in rinse aid.Close the lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in
detergent.Push the lid shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
115
1,70
21
140
1,05
14
75
0,90
15
30
0,70
10
19
0,10
4
35_50_70_65_40_
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive Normal Eco Gentle Quick Prerinse
140
1,60
19
Programme progress / Rinsing noises
m
After the drying cycle, water is pumped out for approx. 60 sec. The programme has not ended until the end display mlights up
Start End display
Alternating rinsing and pumping noises No rinsing noises
15–35 min
Cleaning / Final rinse Dry
Example: Eco programme

Maintenance and care For perfect rinsing results ... Cleaning the waste-water pump *
Strainers ...
Check, if
required, clean
Rotate filter
cylinder, remove
filter system ...
rinse under
flowing water ... Insert ... Screw in filter system NOTE
MARK!
* With some models
–Ladle out water and remove filters
–Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Spray arms ...
Remove
blockages/deposits
Pull lower arm
upwards ... Unscrew upper arm ... Clean spray nozzles under flowing water
(perhaps with
toothpick) ...
Insert lower arm ...
Screw in upper arm
Eliminating minor faults yourself ... ... Self-help pays!
Fault Possible Cause
Device does not work/stops Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Open supply fitting.
Lay supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min when
the water inlet is open.
If the flow rate is less, replace the
supply fitting.
Remedy
Plastic parts / parts of
dishes discoloured Too little cleaning product
Discoloration caused by food colourings
(tomato sauce)
Follow manufacturer’s specifications
(detergent).
Discoloration is quite safe; fades after
subsequent rinse cycles.
Residual water in the device Waste-water pump blocked
Programme not yet ended Clean waste-water pump (see above). Close and switch on the appliance and
wait until the programme ends (end of
programme display lights up) or
terminate programme (see Terminating
the programme).
Fault Possible Cause Remedy
Stains and streaks
Milky residues on dishes
(can be removed)
Cutlery rusty
Rinse aid dosage too high / too low
Glasses not dishwasher-proof.
Cutlery not rust-proof
Hard knife blades are more susceptible
Extraneous rust
Streaks: Reduce dosage.
Water or limescale stains:
Increase dosage.
Use dishwasher-proof glasses.
Use glass-friendly cleaning products.
Use dishwasher-proof cutlery.
Never wash rusting parts in the
appliance.
Further advice can be found in the instruction manual
Milky film, glasses cloudy /
dull (cannot be removed)
Water softening system incorrectly set;
no special salt Set water softening system correctly. Refill with special salt.
Dishes not clean
Sand or grainy residues
on dishes
Utensils are situated too close to each
other or on top of each other
Too little cleaning product
Unsuitable programme selected
Spray nozzles blocked
Filters dirty, not installed securely
Spray arms blocked
Spread out the utensils, avoid contact
between the utensils.
Follow manufacturer’s specifications
(detergent).
Select more intensive programme.
Clean spray arms (see above).
Clean the strainers (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Interrupting the programme Cancelling the programme Arranging utensils
correctly
Whilethe programme is running,
simultaneously press the two
Reset buttons for approx.
3 seconds (RESET).
–Switch off the main switch.
–To continue the programme,
switch on the main switch
again.
Switch off the
appliance.
1 minute after the
programme has
ended, the “pro-
gramme end” dis-
play illuminates.
Arrange dishwasher-proof utensils (without any residual ash, wax, grease,
ink, sticky labels; remove large remnants of jam, dairy products and food)
according to the operating instructions and check that the spray arms can
rotate freely.