NEFF S55T57X0EU User manual

Dishwasher introduction
Quick and easy:
everything you need to know
about your dishwasher...
You should, however, still
read the installation and
operating instructions before
you use the dishwasher for
the first time.
Switch on the appliance the dishwasher starts...
Switch off the appliance that’s it...
Press the on/off switch, the cycle time
for the programme selected appears
Press the on/off switch when
the indicator shows 0 (programme end)
Pour in the water/special salt
Pour in the rinsing agent
Pour in the cleaning agent
Select the programme
9000 008 446    
en Inserting the water softening system * Quick procedure ...
Enter the hardness value ...
ask your
water supplier
* only necessary before the first rinse or
if the water hardness has changed
Read off the setpoint value ... and enter it as shown below ...
Press and hold
the ECO button and the on/off button
Hold the ECO button until
the required value appears
Press the on/off button
+The ECO indicator lamp
and the setpoint value 4
flash
The required setpoint
value appears instead
of ”4”
The setpoint value
is stored
Dissolves limescale (not required for set value 0!)
Unscrew
the lid. Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Cleaning the appliance... Always refill when the level indicator is clear.
Press the
marking,
Lift the
lid
Pour in
the rinsing
agent
Close the
lid.
CLICK
Little dirt, little cleaning agent
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in the
cleaning agent Push the lid too, press.
PLOP
Quick, economical or intensive ...
Programme overview
This overview lists the max. possible number of
programmes. The programmes supplied with your
appliance are indicated on the fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
112
1,60
21
18
140
1,05
14
–
72
0,80
15
12
30
0,80
10
–
19
0,10
4
–
95-145
1,15-1,50
11-19
–
45507055/6540
Duration in minutes
Electricity consumption in kWh
Water consumption in litres
with Aquasensor
AutoIntesive Eco Quick Pre-rinse Gentle
Additional programmes ** Increasedflexibility ...
Soak
...crockery in the lower
basket, programme
starts automatically,
remember to add an
extra 5g of cleaning
agent when the door
unlocks.
Time reduction/
time saving
...shortens the
cleaning time, reduces
the drying.
Upper basket cleaning
...Only the crockery in the
upper basket is cleaned
** on some models
Lower basket cleaning
...Only the crockery in the
lower basket is cleaned h.
Time selection
...switches on as soon as
you press the time
selection button:
Alters the programme
start in hourly steps

Maintenance and care For perfect rinsing results ... Cleaning the waste-water pump *
Strainers ...
Check, if
required, clean
Rotate filter
cylinder, remove
filter system ...
rinse under
flowing water ... Insert ... Screw in filter system NOTE
MARK!
* With some models
– Ladle out water and remove filters
– Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Spray arms ...
Remove
blockages/deposits
Pull lower arm
upwards ... Unscrew upper arm ... Clean spray nozzles under flowing water
(perhaps with
toothpick) ...
Insert lower arm ...
Screw in upper arm
Eliminating minor faults yourself ... ... Self–help pays!
Fault Possible Cause
Device does not work/stops Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Open supply fitting.
Lay supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min when
the water inlet is open.
If the flow rate is less, replace the
supply fitting.
Remedy
Plastic parts / parts of
dishes discoloured
Too little cleaning product
Discoloration caused by food colourings
(tomato sauce)
Follow manufacturer’s specifications
(detergent).
Discoloration is quite safe; fades after
subsequent rinse cycles.
Residual water in the device Waste-water pump blocked
Programme not yet ended Clean waste-water pump (see above). Switch on appliance and close or
terminate programme (see Terminating
the programme).
Cutlery rusty Cutlery not rust-proof
Hard knife blades are more susceptible
Extraneous rust
Use dishwasher-proof cutlery.
Never wash rusting parts in the
appliance.
Fault Possible Cause Remedy
Stains and streaks
Milky residues on dishes
(can be removed)
Rinse aid dosage too high / too low
Glasses not dishwasher-proof.
Streaks: Reduce dosage.
Water or limescale stains: Increase
dosage.
Use dishwasher-proof glasses.
Use glass-friendly cleaning products.
Further advice can be found in the instruction manual
Milky film, glasses cloudy /
dull (cannot be removed)
Water softening system incorrectly set;
no special salt Set water softening system correctly. Refill with special salt.
Dishes not clean
Sand or grainy residues
on dishes
Utensils are situated too close to each
other or on top of each other
Too little cleaning product
Unsuitable programme selected
Spray nozzles blocked
Filters dirty, not installed securely
Spray arms blocked
Spread out the utensils, avoid contact
between the utensils.
Follow manufacturer’s specifications
(detergent).
Select more intensive programme.
Clean spray arms (see above).
Clean the strainers (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Stopping the programme ... Loading the dishwasher correctly ...
Press and hold the two
reset buttons simultaneously for
approximately 3 seconds while
the programme is running
(RESET)
”0” appears
The programme will stop
after 1 minute
Switch off the appliance. Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
large remnants of jam, dairy products and food) according to the operating instructions and check that
the spray arms can rotate freely.