NEFF T58.S2 Series User manual

Induction hob
[en] User manual 2
T58.S2...

en Safety
2
Futher information and explanations are available
online:
Table of contents
1 Safety....................................................................2
2 Avoiding material damage...................................4
3 Environmental protection and saving en-
ergy .......................................................................5
4 Suitable cookware................................................5
5 Familiarising yourself with your appliance ........7
6 TwistPad® ............................................................8
7 Basic operation ....................................................8
8 FlexZone .............................................................10
9 PowerMove.........................................................11
10 Time-setting options..........................................11
11 PowerBoost........................................................12
12 PanBoost ............................................................12
13 Keep-warm function...........................................13
14 Frying Sensor.....................................................13
15 Childproof lock...................................................14
16 Wipe protection..................................................15
17 Individual safety switch-off ...............................15
18 Basic settings.....................................................15
19 Cookware test ....................................................16
20 HomeConnect ...................................................17
21 Hob-based hood control....................................19
22 Cleaning and servicing......................................20
23 Troubleshooting.................................................21
24 Disposal..............................................................22
25 Declaration of Conformity .................................22
26 Customer Service...............................................23
27 Test dishes .........................................................23
1 Safety
Observe the following safety instructions.
1.1 General information
¡Read this instruction manual carefully.
¡Keep the instructions, the appliance pass
and the product information safe for future
reference or for the next owner.
¡Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
Only a licensed professional may connect ap-
pliances without plugs. Damage caused by in-
correct connection is not covered under the
warranty.
The appliance can only be used safely if it is
correctly installed according to the safety in-
structions. The installer is responsible for en-
suring that the appliance works perfectly at its
installation location.
Only use this appliance:
¡To prepare meals and drinks.
¡Under supervision. Never leave the appli-
ance unattended when cooking for short
periods.
¡In private households and in enclosed
spaces in a domestic environment.
¡Up to an altitude of max. 4000m above
sea level.
Do not use the appliance:
¡With an external timer or a separate remote
control. This does not apply if operation
with appliances included in EN 50615 is
switched off.
If you wear an active implantable medical
device (e.g. a pacemaker or defibrillator),
check with your doctor that it complies with
Council Directive 90/385/EEC of 20th June
1990, EN 45502-2-1 and EN 45502-2-2, and
that it has been chosen, implanted and pro-
grammed in accordance with VDE-AR-E
2750-10. If these conditions are satisfied, and
if, in addition, non-metal cooking utensils and
cookware with non-metal handles are used, it

Safety en
3
is safe to use this induction hob as intended.
If these conditions are satisfied, and if, in ad-
dition, non-metal cooking utensils and cook-
ware with non-metal handles are used, it is
safe to use this induction hob as intended.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Do not let children play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.
1.4 Safe use
WARNING‒Risk of fire!
Leaving fat or oil cooking on an unattended
hob can be dangerous and may lead to fires.
▶Never leave hot oil or fat unattended.
▶Never attempt to extinguish a fire using wa-
ter; instead, switch off the appliance and
then cover with a lid or a fire blanket.
The cooking surface becomes very hot.
▶Never place flammable objects on the
cooking surface or in its immediate vicinity.
▶Never place objects on the cooking sur-
face.
The appliance will become hot.
▶Do not keep combustible objects or aero-
sol cans in drawers directly underneath the
hob.
Hob covers can cause accidents, for example
due to overheating, catching fire or materials
shattering.
▶Do not use hob covers.
After every use, switch off the hob using the
main switch.
▶Do not wait until the hob turns off automat-
ically as there are no longer any pots and
pans on it.
Food may catch fire.
▶The cooking process must be monitored. A
short process must be monitored continu-
ously.
WARNING‒Risk of burns!
The appliance and its parts that can be
touched become hot during use, particularly
the hob surround, if fitted.
▶Caution should be exercised here in order
to avoid touching heating elements.
▶Young children under 8 years of age must
be kept away from the appliance.
Hob protective grilles may cause accidents.
▶Never use hob protective grilles.
The appliance becomes hot during operation.
▶Allow the appliance to cool down before
cleaning.
Metal objects on the hob quickly become very
hot.
▶Never place metal objects (such as knives,
forks, spoons and lids) on the hob.
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced with a special
connection cable, which is available from
the manufacturer or his Customer Service.
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶If the surface is cracked, you must switch
off the appliance in order to prevent a pos-
sible electrical shock. To do this, switch off
the appliance via the fuse in the fuse box
rather than at the main switch.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cable is dam-
aged, immediately switch off the fuse in the
fuse box.
▶Call customer services. →Page23
An ingress of moisture can cause an electric
shock.
▶Do not use steam- or high-pressure clean-
ers to clean the appliance.
The insulation on cables of electrical appli-
ances may melt if it touches hot parts of the
appliance.
▶Never bring electrical appliance cables into
contact with hot parts of the appliance.

en Avoiding material damage
4
If metallic objects come into contact with the
fan that is located on the underside of the
hob, this may cause an electric shock.
▶Do not store long, pointed metallic objects
in the drawers below the hob.
WARNING‒Risk of injury!
Saucepans may suddenly jump due to liquid
between the saucepan base and the hotplate.
▶Always keep hotplates and saucepan
bases dry.
▶Never use icy-cold cookware that has been
in the freezer.
When cooking in a bain marie, the hob and
cooking container could shatter due to over-
heating.
▶The cooking container in the bain marie
must not directly touch the bottom of the
water-filled pot.
▶Only use heat-resistant cookware.
An appliance with a cracked or broken sur-
face can cause cuts.
▶Do not use the appliance if it has a cracked
or broken surface.
WARNING‒Danger: Magnetism!
The removable control element is magnetic
and may affect electronic implants, e.g. heart
pacemakers or insulin pumps.
▶Persons with electronic implants must
stand at least 10cm away from the mag-
netic control element. Never put the control
element in your pockets.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.
Children may breathe in or swallow small
parts, causing them to suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
2 Avoiding material damage
This is where you can find the most common causes of damage and tips on how to avoid them.
Damage Cause Measure
Stains Unsupervised cooking process. Monitor the cooking process.
Stains, blisters Spilled food, especially food with a high
sugar content.
Remove immediately with a glass scraper.
Stains, blisters or
fractures in the glass
Defective cookware, cookware with melted
enamel or cookware with copper or alu-
minium base.
Use suitable cookware that is in a good con-
dition.
Stains, discolouration Unsuitable cleaning methods. Only use cleaning agents that are suitable for
glass ceramic, and only clean the hob when
it is cold.
Blisters or fractures in
the glass
Knocks or falling cookware, cooking ac-
cessories or other hard or pointed objects.
When cooking, do not hit the glass or let ob-
jects fall onto the hob.
Scratches, discolour-
ation
Rough cookware bases or moving the cook-
ware on the hob.
Check the cookware. Lift the cookware when
moving it.
Scratches Salt, sugar or sand. Do not use the hob as a work surface or
storage space.
Damage to the appli-
ance
Cooking with frozen cookware. Never use frozen cookware.
Damage to the cook-
ware or the appliance
Cooking without contents. Never place or heat empty cookware on a
hot cooking zone.
Glass damage Melted material on the hot cooking zone or
hot pot lid on the glass.
Do not place greaseproof paper or alu-
minium foil nor plastic containers or pot lids
on the hob.

Environmental protection and saving energy en
5
Damage Cause Measure
Overheating Hot cookware on the control panel or on the
frame.
Never place hot cookware on these areas.
Scratches Material residue between the hob and the
rotary knob TwistPad®.
Keep the rotary knob TwistPad® contact
area clean.
ATTENTION!
A fan is located on the underside of this hob.
▶If a drawer is located on the underside of the hob,
do not store any small or pointed objects, paper or
tea towels in it. These objects may be sucked in
and damage the fan or impair the cooling.
▶There must be a clearance of at least 2cm between
the contents of the drawer and the fan entry point.
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶Sort the individual components by type and dispose
of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use
less energy.
Select the cooking zone to match the size of your
pan. Centre the cookware on the hob.
Use cookware whose base diameter is the same dia-
meter as the hotplate.
Tip:Cookware manufacturers often give the upper
diameter of the saucepan. It is often larger than the
base diameter.
¡Unsuitable cookware or incompletely covered cook-
ing zones consume a lot of energy.
Cover saucepans with suitable lids.
¡Cooking without a lid consumes considerably more
energy.
Lift lids as infrequently as possible.
¡When you lift the lid, a lot of energy escapes.
Use a glass lid.
¡You can see into the pan through a glass lid
without having to lift it.
Use pots and pans with flat bases.
¡Uneven bases increase energy consumption.
Use cookware that is suitable for the quantity of food.
¡Large items of cookware containing little food need
more energy to heat up.
Cook with only a little water.
¡The more water that is contained in the cookware,
the more energy is required to heat it up.
Turn down to a lower power level early on.
¡If you use an ongoing power level that is too high,
you will waste energy.
Product Information according (EU) 66/2014 can be
found on the attached appliance pass and online on
the product page for your appliance.
4 Suitable cookware
Cookware that is suitable for induction cooking must
have a ferromagnetic base, i.e. it must be attracted by
a magnet. The base must also match the size of the
cooking zone. If cookware is not detected on a cooking
zone, place this on the cooking zone with the next
smallest diameter.
4.1 Size and characteristics of the cookware
To correctly detect the cookware, take the size and the
material of the cookware into consideration. All cook-
ware bases must be perfectly flat and smooth.
You can use Cookware test to check whether your
cookware is suitable. You can find more information
about this under
→"Cookware test", Page16.

en Suitable cookware
6
Cookware Materials Properties
Recommended cook-
ware
Stainless steel cookware in a sandwich
design that distributes the heat well.
This cookware distributes the heat evenly,
heats up quickly, and ensures that it can be
detected easily.
Ferromagnetic cookware made of enamelled
steel, cast iron or special induction cookware
made of stainless steel.
This cookware heats up quickly and ensures
that it can be detected easily.
Suitable The base is not fully ferromagnetic. If the ferromagnetic area is smaller than the
base of the cookware, only the area that is
ferromagnetic heats up. As a result, the heat
is not distributed evenly.
Cookware bases with aluminium content. These reduce the ferromagnetic area, which
means that less power is emitted to the
cookware. This cookware may not be suffi-
ciently detected or may not be detected at
all, and therefore does not heat sufficiently.
Not suitable Cookware made from normal thin steel,
glass, clay, copper or aluminium.
Notes
¡Do not use adapter plates between the hob and the
cookware.
¡Do not heat up empty cookware and do not use
cookware with a thin base, as this may become very
hot.

Familiarising yourself with your appliance en
7
5 Familiarising yourself with your appliance
5.1 Cooking with induction
In comparison to conventional hobs, induction techno-
logy brings with it a series of changes and has a num-
ber of benefits such as time savings when cooking and
frying, energy savings as well as greater ease of clean-
ing and care. It also offers improved heat control as the
heat is generated directly in the cookware.
5.2 Control panel
Individual details, such as colour and shape, may differ
from the figure.
Tips
¡Always keep the control panel clean and dry.
¡Do not place any cookware near the displays or
sensors. The electronics may overheat.
Selection sensors
When you switch on the hob, the controls that are avail-
able at this time light up.
Sensor Function
⁠ Main switch
⁠ Keep-warm function
⁠ PowerBoost / PanBoost
⁠ Frying Sensor
⁠ FlexZone
⁠ PowerMove
⁠ Runtime
⁠ Switch-off timer
⁠ Timer / Childproof lock
⁠ Hob-based hood control
⁠ Hood light
Note:As soon as the connection to HomeConnect has
been established, ⁠ lights up.
Depending on the status of the hob, the displays for
the cooking zones and the various activated and avail-
able functions also light up.
5.3 Distribution of the cooking zones
The specified power has been measured with the
standard pots, which are described in IEC/EN
60335-2-6. The power may vary depending on the size
of the cookware or cookware material.
BC
D
A
Area Highest power level
⁠ 18cm dia-
meter
Power level 9
PowerBoost
1800W
3100W
⁠ 14.5 cm
diameter
Power level 9
PowerBoost
1400W
2200W
⁠ 24cm dia-
meter
Power level 9
PowerBoost
2200W
3700W
⁠ ⁠ ⁠ ⁠ Power level 9
PowerBoost
2200W
3700W
⁠ ⁠ Power level 9
PowerBoost
3300W
3700W

en TwistPad®
8
5.4 Cooking zone
Before you start cooking, check whether the size of the
cookware fits the cooking zone that you want to use for
cooking:
Area Cooking zone type
⁠ Flex Zone
→"FlexZone", Page10
⁠ Single-circuit cooking zone
5.5 Residual heat indicator
The hob has a residual heat indicator for each cooking
zone. Do not touch the cooking zone if the residual
heat indicator is lit.
Display Meaning
⁠ The cooking zone is hot.
⁠ The cooking zone is warm.
6 TwistPad®
The TwistPad® control is a pull-out rotary knob which
can be used to select the cooking zones and power
levels. As it is magnetic, it automatically centres itself in
its special programming zone.
6.1 Positioning and operating the
TwistPad®
Position the rotary knob so that it is centred on the pro-
gramming zone in relation to the displays that limit this
zone.
To switch on a cooking zone, touch TwistPad® at the
level of the required cooking zone. Turn the rotary knob
to select the power level.
Note:The rotary knob still functions correctly even if
the knob is not precisely centred.
Always keep the rotary knob clean. Soiling may impair
its function.
6.2 Instructions for use
¡A strong magnet is located inside the rotary knob.
Keep the rotary knob away from magnetic data car-
riers such as credit cards and cards with magnetic
strips. It may damage them. The magnet may also
cause faults on televisions and screens.
¡The rotary knob is magnetic. Metal particles stuck to
the bottom may scratch the surface of the hob. Al-
ways clean the twist knob thoroughly.
6.3 Removing TwistPad®
You can remove the rotary knob from the cooking zone
during the cooking process.
If you remove the controller, Wipe protection is
switched on for 35 seconds. If the rotary knob is not re-
turned to its position before this time elapses, the hob
switches off.
WARNING‒Risk of fire!
The hob may continue to heat up. If, during this 35
seconds, a metallic object is placed in the area of the
TwistPad, the hob may continue to heat up.
▶Always switch off the hob at the main switch.
6.4 Operation without rotary knob
TwistPad®
You can also operate the hob without TwistPad®:
1. Switch on the hob using the main switch.
2. Within the next 5 seconds, simultaneously press
and hold ⁠ and ⁠for 4 seconds. An audible signal
sounds.
3. Press ⁠ repeatedly until the display for the required
hob lights up.
4. Then set the required power level using ⁠ or ⁠.
aThe cooking zone is switched on.
Notes
¡You cannot switch on the timer without the rotary
knob.
¡You can always position the rotary knob in the pro-
gramming zone again.
7 Basic operation
7.1 Switching on the hob
▶Touch ⁠.
The symbols for the cooking zones and the cur-
rently available functions light up. ⁠light up next to
the cooking zones. Set the rotary knob TwistPad®
to the setting range.
aThe hob is ready for use.
ReStart
▶If you switch the appliance on within four seconds of
switching it off, the hob operates with the settings
that were previously set.
7.2 Switching the hob off
▶Touch ⁠ until the displays go out.
aAll cooking zones are switched off.
Note:If all of the cooking zones are switched off for
longer than 15seconds, the hob is automatically
switched off.

Basic operation en
9
7.3 Setting the power level in the cooking
zones
The cooking zone has 17 power levels, which are dis-
played from ⁠ to ⁠ with intermediate values. Select the
best power level for the food and the planned cooking
process.
1. Select the cooking zone. To do this, touch Twist-
Pad® at the level for the required hob.
a⁠ lights up brighter.
2. Turn the TwistPad® until the required power level
lights up in the display.
aThe power level has been set.
Note:If no cookware is placed on the cooking zone or
the pot is not suitable, the selected power level flashes.
After a certain period of time, the cooking zone
switches itself off.
QuickStart
▶If you place cookware on the hob before you switch
it on, the cookware is detected when you switch on
and the corresponding cooking zone is selected
automatically. Select the power level in the next 20
seconds, or the hob switches itself off.
Changing the power level and switching off the
cooking zone
1. Select the cooking zone.
2. Select the required power level or use the ⁠ to set it
to TwistPad®.
aThe cooking zone's power level changes or the
cooking zone switches itself off and the residual
heat indicator appears.
7.4 Cooking tips
¡When heating up puree, cream soups or thick
sauces, stir occasionally.
¡To preheat, set the power level 8-9.
¡When cooking with the lid on, reduce the power
level as soon as you see steam escaping. The
cooking result is not affected by the steam escap-
ing.
¡After cooking, place a lid on the cookware until you
serve the dish.
¡To cook with the pressure cooker, observe the man-
ufacturer's instructions.
¡Do not cook food for too long, otherwise nutrients
will be lost. The kitchen timer enables you to set the
optimal cooking time.
¡Ensure that the oil does not smoke.
¡To brown the food, fry it in small portions, one after
the other.
¡Some items of cookware may reach high temperat-
ures while the food is cooking. You should therefore
use oven gloves.
¡You can find recommendations for energy-efficient
cooking under
→"Saving energy", Page5
Cooking recommendations
The table shows which power level ( ⁠) is suitable for
which food. The cooking time ( ⁠) may vary de-
pending on the type, weight, thickness and quality of
the food.
⁠ ⁠
Melting
Chocolate coating 1-1. -
Butter, honey, gelatine 1-2 -
Heating and keeping warm
Stew, e.g. lentil stew 1.-2 -
Milk11.-2. -
Boiled sausages13-4 -
Defrosting and heating
Spinach, frozen 3-4 15-25
1Without lid
2Preheat to power level 8 - 8.
⁠ ⁠
Goulash, frozen 3-4 35-55
Poaching, simmering
Potato dumplings 14.-5. 20-30
Fish 14-5 10-15
White sauces, e.g. Béchamel
sauce
1-2 3-6
Whisked sauces, e.g.
Béarnaise sauce, Hollandaise
sauce
3-4 8-12
Boiling, steaming, braising
Rice, with double the volume of
water
2.-3. 15-30
Rice pudding 22-3 30-40
Unpeeledboiled pots 4.-5. 25-35
Boiled potatoes 4.-5. 15-30
Pasta 16-7 6-10
Stew 3.-4. 120-
180
Soups 3.-4. 15-60
Vegetables 2.-3. 10-20
Vegetables, frozen 3.-4. 7-20
Stew in a pressure cooker 4.-5. -
Stewing
Rolled roasting joint 4-5 50-65
Pot roast 4-5 60-100
Goulash 23-4 50-60
Braising/frying with a small
amount of fat 1
Escalope, plain or breaded 6-7 6-10
Escalope, frozen 6-7 6-12
Chops, plain or breaded 6-7 8-12
Steak (3 cm thick) 7-8 8-12
Poultry breast (2 cm thick) 5-6 10-20
1Without lid
2Preheat to power level 8 - 8.

en FlexZone
10
⁠ ⁠
Poultry breast, frozen 5-6 10-30
Rissoles (3 cm thick) 4.-5. 20-30
Hamburgers (2 cm thick) 6-7 10-20
Fish and fish fillet, plain 5-6 8-20
Fish and fish fillet, breaded 6-7 8-20
Fish, breaded and frozen, e.g.
fish fingers
6-7 8-15
Prawns and scampi 7-8 4-10
Sautéing fresh vegetables and
mushrooms
7-8 10-20
Stir-fry, vegetables, meat cut in
strips Asian-style
7-8 15-20
Frozen dishes, e.g. stir-fries 6-7 6-10
Pancakes, cooked one after the
other
6.-7. -
1Without lid
2Preheat to power level 8 - 8.
⁠ ⁠
Omelette (cooked one after the
other)
3.-4. 3-10
Fried eggs 5-6 3-6
Deep-frying, 150–200g per
portion in 1–2l oil, deep-fat
fried in portions1
Frozen products, e.g. chips,
chicken nuggets
8-9 -
Croquettes, frozen 7-8 -
Meat, e.g. chicken portions 6-7 -
Fish, breaded or battered 6-7 -
Vegetables, mushrooms,
breaded, beer-battered or tem-
pura
6-7 -
Small baked items, e.g. dough-
nuts, battered fruit
4-5 -
1Without lid
2Preheat to power level 8 - 8.
8 FlexZone
The flexible cooking zone allows you to position cook-
ware of any shape or size any way you like. It consists
of four inductors that work independently of each other.
When the flexible cooking zone is in use, only the area
that is covered by cookware is activated.
8.1 Positioning the cookware
The flexible cooking zone can be configured in two
ways, depending on which cookware is used. In order
to guarantee good thermal detection and heat distribu-
tion, we recommend positioning the cookware in the
centre, as shown in the figures.
As a connected cooking zone
Recommended for cooking with just one item of cook-
ware.
¡Position the cookware depending on the size:
Ø ≤ 13 cm. Ø > 13 cm.
¡Recommended oblong cookware ⁠:
As two separate cooking zones
Recommended for cooking with two items of cook-
ware.
You can use the front and rear zone independently of
one another, and set a separate power level for each
zone.
8.2 FlexZone connect
By default, the flexible zone is configured as two separ-
ate cooking zones. Switch on the following function to
connect the cooking zones:
1. Select one of the two cooking zones.
2. Press ⁠.
a⁠ lights up. The FlexZone is connected.
Note:If you move or lift the cookware from an active
connected cooking zone, an automatic search starts.
Each item of cookware that is found within the cooking
zone during this search is heated at the previously se-
lected power level.
8.3 FlexZone disconnecting
▶Touch ⁠.
aThe cooking zones are separated and work inde-
pendently of each other.

PowerMove en
11
9 PowerMove
You can use this function to change the power level of
an item of cookware by simply sliding it forwards or
backwards in the flexible cooking zone. The zone is di-
vided into three areas with different power levels.
9.1 Positioning and moving the cookware
Only use one item of cookware. The cooking area de-
pends on the cookware used, as well as its size and
positioning.
Each cooking area has a preset power level:
¡Front area = power level ⁠
¡Middle area = power level ⁠
¡Rear area = power level ⁠
You can change the standard setting of the preset
power levels. You can find out how to do this in the
"Basic settings" section →Page15.
9.2 Activating PowerMove
Requirement:Only place one item of cookware on a
flexible zone.
1. Select one of the two cooking zones in the flexible
zone.
2. Press ⁠.
a⁠ and the power level for the area in which the con-
tainer is located light up.
aThe function is switched on.
Note:You can change the power levels during cook-
ing.
9.3 Deactivating PowerMove
▶Touching ⁠
a⁠ goes out.
aThe function has been deactivated.
10 Time-setting options
Your hob has various functions for setting the cooking
time:
¡Switch-off timer
¡Timer
¡Runtime
10.1 Switch-off timer
Allows you to program a cooking time for one or more
cooking zones. Once the time has elapsed, the cook-
ing zone is automatically switched off.
Switching on Switch-off timer
1. Select the cooking zone and the power level.
2. Press ⁠.
aThe ⁠ indicator for the hotplate will light up.
3. Use TwistPad® to select the cooking time.
aThe cooking time begins to count down.
aOnce the cooking time has elapsed, the cooking
zone switches itself off and an audible signal
sounds.
Note:When you set a cooking time for a cooking zone
in which the Frying Sensor is activated, the cooking
time will not start counting down until the selected tem-
perature level has been reached.
Changing or switching off Switch-off timer
1. Select the cooking zone and touch ⁠.
2. Use TwistPad® to change the cooking time or set to
⁠ to delete the cooking time.
10.2 Timer
Enables the activation of a timer of 0–99 minutes. This
function can be used independently of the cooking
zones and other settings. It does not automatically
switch off the cooking zones.
Switching on Timer
1. Touch ⁠.
2. Use TwistPad® to select the required time.
3. Press ⁠ to confirm.
aThe time begins to count down.

en PowerBoost
12
aAn audible signal sounds and the displays flash
once the time has elapsed.
Changing or switching off the Timer
1. Touch ⁠.
2. Change the running time using TwistPad® or set to
⁠ to delete the running time.
3. Press ⁠ to confirm.
10.3 Runtime
The stopwatch function displays the time that has
elapsed since activation.
Switching on Runtime
▶Touch ⁠.
a⁠ light up.
aThe time begins to count down.
Switching off Runtime
▶Touch ⁠.
aThe displays for the run time programming function
go out.
aThe function has been deactivated.
11 PowerBoost
You can use this function to heat up large volumes of
water more quickly than with ⁠.
This function is available for all cooking zones,
provided the other cooking zone in the same group is
not in use.
11.1 Switching on PowerBoost
1. Select the cooking zone.
2. Touch ⁠. The ⁠ and ⁠ displays light up.
aThe function is switched on.
Note:You can also switch on this function when cook-
ing with a connected FlexZone.
11.2 Switching off PowerBoost
1. Select the cooking zone.
2. Touch ⁠. The ⁠ and ⁠ displays go out and the
cooking zone switches back to power level ⁠.
aThe function has been deactivated.
Note:In certain circumstances, this function may
switch itself off automatically in order to protect the
electronic elements inside the hob.
12 PanBoost
You can use this function to heat up pans more quickly
than with ⁠.
This function is available for all cooking zones,
provided the other cooking zone in the same group is
not in use.
12.1 Recommended applications
¡Do not place a lid on the pan.
¡Never leave pans unattended when they are heating
up.
¡Only use cold pans.
¡Use pans with a completely flat base. Do not use
pans with a thin base.
12.2 Switching on PanBoost
1. Select the cooking zone.
2. Touch ⁠twice. ⁠ and ⁠ light up.
aThe function is switched on.
Note:You can also switch on this function when cook-
ing with a connected FlexZone.
12.3 Switching off PanBoost
1. Select the cooking zone.
2. Touch ⁠. ⁠ and ⁠ go out and the cooking zone
switches back to power level ⁠.
aThe function has been deactivated.
Note:To avoid high temperatures, this function auto-
matically switches itself off after 30 seconds.

Keep-warm function en
13
13 Keep-warm function
You can use this function to melt chocolate or butter
and to keep meals warm.
13.1 Switching on Keep-warm function
1. Select the required cooking zone.
2. Touch ⁠ within the next 10 seconds.
⁠ lights up.
aThe function is switched on.
13.2 Switching off Keep-warm function
1. Select the cooking zone.
2. Touch ⁠.
⁠ goes out.
aThe function has been deactivated.
14 Frying Sensor
Suitable for cooking or reducing sauces, pancakes or
frying eggs with butter, for frying vegetables or steaks
up to the required level of boiling, and for keeping the
temperature under control.
Instead of frequently adjusting the power level during
cooking, select the required target temperature once at
the start. The sensors under the glass ceramic meas-
ure the temperature of the cookware and keep this
constant throughout the entire cooking process.
This function is available on all cooking zones marked
with this symbol ⁠.
14.1 Advantages
¡The temperature is automatically kept constant
without you having to change the power level.
¡Oil does not overheat. This prevents the food from
burning.
¡The cooking zone only continues heating for as long
as this is necessary to maintain the temperature.
This saves energy.
14.2 Temperature levels
Temperature levels for preparing meals.
Level Temper-
ature
Functions Cookware
1 120ºC Boiling and reducing
sauces, fry veget-
ables
2 140ºC Searing in olive oil or
butter
3 160ºC Frying fish and
coarse foods
4 180ºC Deep-fat frying
breaded, frozen and
grilled food
5 215ºC High-temperature grill
and griddle plate
14.3 Recommended cookware
Special cookware has been developed for this function,
which delivers the best results.
Cookware Recommended cooking
zone
Frying pan, 21cmdia-
meter
Single cooking zone
Teppanyaki ⁠ Flex Zone
Grill ⁠ Flex Zone
The recommended cookware is available from cus-
tomer service, specialist retailers or our online shop
www.neff-international.com.
Note:You can also use other cookware. Depending on
the composition of the cookware, the achieved temper-
ature may differ from the selected temperature level.
14.4 Switching on the Frying Sensor
1. Place empty cookware on the cooking zone.
2. Select the cooking zone and touch ⁠.
3. Within the next 5 seconds, use the rotary knob
TwistPad® to select the required temperature level.
aThe functions starts. ⁠ flashes until the set target
temperature is reached.
aOnce the target temperature has been reached, a
signal tone sounds and ⁠ stops flashing.
4. Add the frying fat and then the food to the frying
pan.
Note:If you need to cook with more than 250ml oil,
add the oil and wait a few seconds before you add the
food.
14.5 Switching off Frying Sensor
▶Select the cooking zone and touch ⁠.
aThe function has been deactivated.
14.6 Recommendations for cooking with the
Frying Sensor
The following table shows the ideal temperature levels
for a selection of dishes. The temperature ⁠ and the
cooking time ⁠ depend on the amount, condition
and quality of the food.
¡⁠ Frying pan
¡⁠Teppanyaki

en Childproof lock
14
¡⁠Griddle plate
Cookware ⁠ ⁠
Meat
Escalope ⁠ ⁠ ⁠ 4 6-10
Escalope, breaded ⁠ 4 6-10
Fillet ⁠ ⁠ ⁠ 4 6-10
Chops ⁠ ⁠ ⁠ 3 10-15
Cordon bleu, Wiener
Schnitzel
⁠ 4 10-15
Steak, rare, 3cm thick ⁠ ⁠ ⁠ 5 6-8
Steak, medium, 3cm thick ⁠ ⁠ ⁠ 5 8-12
Steak, well-done, 3cm thick ⁠ ⁠ ⁠ 4 8-12
T-bone steak, rare, 4.5cm
thick
⁠ ⁠ ⁠ 5 10-15
T-bone steak, medium,
4.5cm thick
⁠ ⁠ ⁠ 5 20-30
Poultry breast, 2 cm thick ⁠ ⁠ ⁠ 3 10-20
Bacon ⁠ ⁠ ⁠ 2 5-8
Minced meat ⁠ ⁠ 4 6-10
Hamburgers, 1.5cm thick ⁠ ⁠ ⁠ 3 6-15
Meatballs, 2cm thick ⁠ 3 10-20
Sausages ⁠ ⁠ ⁠ 3 8-20
Chorizo, fresh sausages ⁠ ⁠ ⁠ 3 10-20
Skewers, kebabs ⁠ ⁠ ⁠ 3 10-20
Gyros ⁠ ⁠ 4 7-12
Fish and seafood
Fish fillet ⁠ ⁠ ⁠ 4 10-20
Fish fillet, breaded ⁠ 4 10-20
Fish, fried, whole ⁠ ⁠ ⁠ 3 10-20
Sardines ⁠ ⁠ ⁠ 4 6-12
Scampi, prawns ⁠ ⁠ ⁠ 4 4-8
Squid, cuttlefish ⁠ ⁠ ⁠ 4 6-12
Egg dishes
Fried eggs in butter ⁠ ⁠ 2 2-6
Fried eggs ⁠ ⁠ 4 2-6
Scrambled eggs ⁠ ⁠ 2 4-9
Omelette ⁠ ⁠ 2 3-6
Cookware ⁠ ⁠
French toast ⁠ ⁠ 3 4-8
Crêpes, blinis, pancakes, ta-
cos
⁠ ⁠ 5 1-3
Vegetables
Roast potatoes ⁠ ⁠ 5 6-12
Chips ⁠ 4 15-25
Potato pancakes ⁠ ⁠ 5 2-4
Onions, roasted garlic ⁠ ⁠ 2 2-10
Onion rings ⁠ 3 5-10
Courgettes, aubergines, pep-
pers
⁠ ⁠ ⁠ 2 4-12
Green asparagus ⁠ ⁠ ⁠ 3 4-15
Mushrooms ⁠ ⁠ ⁠ 4 10-15
Vegetables, braised in oil ⁠ 1 10-20
Vegetables in tempura batter ⁠ 4 5-10
Frozen products
Chicken nuggets ⁠ 4 10-15
Fish fingers ⁠ 4 8-12
Chips ⁠ 5 4-8
Stir-fries ⁠ 3 6-10
Spring rolls ⁠ 4 10-30
Pastries, croquettes ⁠ 5 3-8
Sauces
Tomato sauce ⁠ 1 25-35
Béchamel sauce ⁠ 1 10-20
Cheese sauce ⁠ 1 10-20
Sweet sauces ⁠ 1 15-25
Sauces, reduced ⁠ 1 25-35
Other
Fried cheese ⁠ ⁠ 3 7-10
Croutons ⁠ ⁠ 3 6-10
Toasted bread ⁠ ⁠ ⁠ 4 4-8
Dried ready meals ⁠ 1 5-10
Almonds, walnuts, pine nuts,
roasted
⁠ ⁠ 4 3-15
Popcorn ⁠ 5 3-4
15 Childproof lock
The hob is equipped with a childproof lock. This pre-
vents children from switching on the hob.
15.1 Switching on Childproof lock
Requirement:The hob must be switched off.
▶Touch and hold ⁠ for 4 seconds.
aThe ⁠ display lights up for 10seconds.
aThe hob is locked.
15.2 Switching off Childproof lock
▶Touch and hold ⁠ for 4 seconds.
aThe lock is released.
15.3 Automatic childproof lock
You can also activate the childproof lock automatically
every time the hob is switched off.
You can find out how to switch the function on and off
in the "Basic settings" section →Page15.

Wipe protection en
15
16 Wipe protection
Allows the control panel to be locked for cleaning so
that the settings are not inadvertently adjusted.
The lock has no effect on the main switch.
16.1 Switching on Wipe protection
▶Remove the rotary knob TwistPad®. ⁠ lights up.
aThe control panel remains locked for 35seconds. A
signal tone sounds 5 seconds before the appliance
is switched off.
16.2 Switching off Wipe protection
To switch off the function early:
▶Press TwistPad® and turn it until ⁠ goes out.
aThe control panel is unlocked.
17 Individual safety switch-off
The safety function is activated if one cooking zone is
in operation for an extended period and you do not
change any settings. The cooking zone displays ⁠ ⁠
and switches itself off.
The time from 1 to 10 hours depends on the selected
power level.
Press any button to switch on the cooking zone.
18 Basic settings
You can configure the basic settings for your appliance to meet your needs.
18.1 Overview of the basic settings
Display Setting Value
⁠ ⁠ Childproof lock ⁠ - Manual.1
⁠ Automatic.
⁠ – Switched off.
⁠ ⁠ Audible signals ⁠ – Confirmation and fault signals are switched off.
⁠ – Only the fault signal is switched on.
⁠ – Only the confirmation signal is switched on.
⁠ – All signal tones are switched on 1.
⁠ ⁠ Energy consumption display
Shows the total energy consumption
between switching the hob on and off in
kWh.
The accuracy of the display depends on vari-
ous factors such as the voltage quality of the
power supply.
⁠ – Switched off.1
⁠ – Switched on.
⁠ ⁠ Automatic switch-off of the cooking zones. ⁠ ⁠ – switched off.1
⁠ ⁠- ⁠ ⁠ - minutes until the appliance switches off auto-
matically.
⁠ ⁠ Duration of the timer end signal tone ⁠ – 10seconds
⁠ – 30seconds
⁠ - 1 minute 1.
1Factory setting

en Cookware test
16
Display Setting Value
⁠ ⁠ Power limitation
Enables the total power of the hob to be lim-
ited, if necessary, based on the conditions of
your electrical installation. The available set-
tings depend on the maximum power of the
hob. You can find precise information on the
rating plate. If the function is active and the
hob has reached the set power limit, ⁠ is dis-
played and you cannot select a higher power
level.
⁠ - Switched off. Maximum power of the hob 1.
⁠ - 1000 W. Lowest power setting.
⁠. - 1500 W.
...
⁠ - 3000 W. Recommended for 13 A.
⁠. - 3500 W. Recommended for 16 A.
⁠ - 4000 W.
⁠. - 4500 W. Recommended for 20 A.
...
⁠ - Maximum power of the hob.
⁠ ⁠ Time for selecting the cooking zone ⁠ - Unlimited: You can adjust the last selected cooking
zone without having to select it again.1
⁠ – Limited: You can adjust the last selected cooking
zone within 10seconds after selecting it. After this time,
you must select the cooking zone again before adjusting
it.
⁠ ⁠ ⁠ PowerMove
Allows you to change the preset power levels
for the three cooking areas of the flexible
cooking zone.
Select one of the two cooking zones, set the
required power level in the settings area and
touch ⁠ to confirm the new power level.
⁠ - Preset power level for the front cooking zone.
⁠ - Preset power level for the middle cooking zone.
⁠ - Preset power level for the rear cooking zone.
⁠ ⁠ ⁠ Cookware test
You can use this function to test the quality
of the cookware.
⁠ - Not suitable.
⁠ - Not optimal.
⁠ - Suitable.
⁠ ⁠ Restoring factory settings ⁠ - Individual settings 1.
⁠ - Factory settings.
1Factory setting
18.2 To go to the basic settings
Requirement:The hob must be switched off.
1. To switch on the hob, touch ⁠.
2. Within the next 10 seconds, press and hold ⁠ for 4
seconds.
Product information Display
Directory for the technical after-sales
service (TK)
⁠ ⁠
Production number ⁠ ⁠
Production number 1 ⁠ ⁠.
Production number 2 ⁠. ⁠
aThe first four displays provide the product informa-
tion. To call up each display, turn the rotary knob
TwistPad®.
3. Touch ⁠ to access the basic settings.
a⁠ ⁠ and ⁠ light up as a presetting.
4. Touch ⁠ repeatedly until the desired setting ap-
pears.
5. Use TwistPad® to select the required setting.
6. Touch and hold ⁠ for 4seconds.
aThe settings are saved.
18.3 Discarding changes to the basic
settings
▶Touch ⁠.
aAll changes are discarded and not saved.
19 Cookware test
The quality of the cookware has a major influence on
the speed and the result of the cooking process.
You can use this function to test the quality of the cook-
ware.
Before the test, ensure that the size of the cookware
base corresponds to the size of the cooking zone be-
ing used.
Access is via the basic settings. →Page15
19.1 Carrying out Cookware test
As a single cooking zone, the flexible cooking zone is
set in such a way that only the individual item of cook-
ware is checked.
1. At room temperature, place the cookware with ap-
prox.200ml water in the centre of the cooking zone
that best fits the base of the cookware in terms of
size.
2. Call up the basic settings and select ⁠ ⁠ ⁠.

HomeConnect en
17
3. Turn TwistPad®. ⁠ flashes in the cooking zones.
aThe function is switched on.
aAfter 20 seconds, the result appears in the cooking
zone displays.
19.2 Checking the result
You can see what the result means for the quality and
speed of the cooking process in the following table.
Result
The cookware is not suitable for the cooking zone
and therefore does not heat up.
The cookware is taking longer to heat up than ex-
pected and cooking is not progressing as well as
it ought to.
The cookware is heating up correctly and cooking
is progressing well.
Note:If you have any unfavourable results, reposition
the cookware on a smaller cooking zone, if available.
To reactivate the function, turn TwistPad®.
20 HomeConnect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the HomeConnect app, adjust its basic settings
and monitor its operating status.
The HomeConnect services are not available in every
country. The availability of the HomeConnect function
depends on the availability of HomeConnect services
in your country. You can find information about this at:
www.home-connect.com.
The HomeConnect app guides you through the entire
login process. Follow the instructions in the HomeCon-
nect app to configure the settings.
Tips
¡Please consult the documents supplied by
HomeConnect.
¡Please also follow the instructions in the HomeCon-
nect app.
Notes
¡Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the HomeCon-
nect app.
→"Safety", Page2
¡Hobs are not designed to be left unattended. Al-
ways monitor the cooking process.
¡Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the HomeConnect
app.
¡In networked standby mode, the appliance requires
a maximum of2W.
20.1 Setting up HomeConnect
Requirements
¡The appliance is connected to the power supply and
is switched on.
¡You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡The mobile device and the appliance are within
range of your home network's Wi-Fi signal.
1. Download the HomeConnect app.
2. Open the HomeConnect app and scan the follow-
ing QR code.
3. Follow the instructions in the HomeConnect app.
20.2 Overview of the HomeConnect settings
You can adjust the settings and network settings for HomeConnect by going to your hob's basic settings.
Setting Selection or display Additional information
⁠ ⁠ ⁠ Network connection
⁠ – Not connected/disconnect network
⁠ – Connect automatically
⁠ – Connect manually
⁠ – Connected
Log on the hob in the Wi-Fi home network (Wi-Fi) or dis-
connect from the network
1Factory setting

en HomeConnect
18
Setting Selection or display Additional information
⁠ ⁠ ⁠ Connection to app
⁠ – Not connected
⁠ – Connect
⁠ ⁠ ⁠ is only displayed if the hob is connected to the
home network.
⁠ ⁠ ⁠ Connection to the Wi-Fi
⁠ – Wireless module switched off
⁠ – Wireless module switched on
If Wi-Fi has been activated, you can use the HomeCon-
nect functions.
⁠ ⁠ ⁠ is only displayed if the hob has been previously
connected to a network.
⁠ ⁠ ⁠ Set using the app
⁠ – Switched off
⁠ – Switched on1
If ⁠ ⁠ ⁠ is switched off, only the hob's operating statuses
are displayed in the HomeConnect app.
⁠ ⁠ ⁠ Software update
⁠ – Update available and ready to in-
stall
⁠ – Start installation
⁠ ⁠ ⁠ is only displayed if a software update is available.
⁠ ⁠ ⁠ Controlling remote access by after-
sales service
⁠ – Not authorised
⁠ – Authorised
⁠ ⁠ ⁠ is only displayed if after-sales service is attempting
to connect to the hob. After granting access, you can ter-
minate this at any time.
⁠ ⁠ ⁠ Display Wi-Fi signal strength
⁠ – Not connected to the WLAN home
network (Wi-Fi)
⁠ – Signal strength 1 (poor)
⁠ – Signal strength 2 (moderate)
⁠ – Signal strength 3 (good)
⁠ ⁠ ⁠ is only displayed if there is a connection to the
WLAN home network (Wi-Fi).
⁠ ⁠ ⁠ Connection to HomeConnect server
⁠ – Not connected
⁠ – Connected
⁠ ⁠ ⁠ is only displayed if there is a connection to the
WLAN home network (Wi-Fi).
1Factory setting
20.3 Changing settings via the
HomeConnect app
You can use the HomeConnect app to change the set-
tings for the cooking zones and send them to the hob.
Requirements
¡The hob is connected to the Wi-Fi and to the
HomeConnect app.
¡To use the HomeConnect app to set the hob, ⁠ ⁠ ⁠
must be switched on in the basic settings. ⁠ ⁠ ⁠ is
switched on on delivery. If the option for the trans-
mission of settings has been deactivated, only the
hob's operating statuses are displayed in the
HomeConnect app.
1. Select the setting in the HomeConnect app and
send it to the hob.
Follow the instructions in the HomeConnect app.
Settings that you send from the HomeConnect app
to the hob must be confirmed on the hob.
aAs soon as cooking settings are transmitted to a
cooking zone, the display starts to flash, depending
on the setting.
2. To confirm the setting, touch the twist knob in the
area of the required hotplate.
3. To discard the setting, touch any other touch field
on the hob.
20.4 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nectuser, have installed the app on your mobile device
and be connected to the HomeConnectserver.
As soon as a software update is available, you will be
informed via the HomeConnectapp and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the HomeConnectapp if you are in your
WLAN home network (Wi-Fi). The HomeConnectapp
will inform you once installation is successful.
Notes
¡You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡We recommend that you install security updates as
soon as possible.

Hob-based hood control en
19
20.5 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the HomeConnect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip:For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com
20.6 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
HomeConnect server (initial registration):
¡Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
¡The current software and hardware version of your
appliance.
¡Status of any previous reset to factory settings.
This initial registration prepares the HomeConnect
functions for use and is only required when you want to
use the HomeConnect functions for the first time.
Note:Please note that the HomeConnect functions
can only be utilised with the HomeConnect app. In-
formation on data protection can be retrieved in the
HomeConnect app.
21 Hob-based hood control
If both appliances are HomeConnect-compatible, con-
nect the appliances in the HomeConnectapp. To do
this, connect the two appliances to HomeConnect and
follow the instructions in the app.
Notes
¡Regular security updates are provided for your ap-
pliance. If you have connected your hob directly to
an extractor hood, both of these appliances cannot
receive these security updates. To ensure the safe
use of the appliance, we recommend connecting
both appliances to each other via HomeConnect
and installing these updates as soon as they are
provided. A HomeConnect account (which is free of
charge) is required for this.
¡Using the controls on the extractor hood always
takes priority. It is not possible to use the hob-based
hood control during this time.
¡In networked standby mode, the appliance requires
a maximum of2W.
¡You can only connect to the extractor hood via the
HomeConnect app. Other connection routes are no
longer supported.
21.1 Resetting HomeConnectsettings
If you have problems connecting your appliance to the
WLAN home network (Wi-Fi) or if you want to log your
appliance onto a different WLAN home network (Wi-Fi) ,
you can reset the HomeConnect settings.
Note:If you reset the HomeConnect settings, the con-
nection to any extractor hood will also be terminated.
1. Press and hold ⁠ for 4seconds.
aThe display will show the product information.
2. Touch ⁠ repeatedly until the display alternately
shows ⁠ and ⁠ ⁠.
3. Use the twist knob to set the value to ⁠.
21.2 Controlling the extractor hood via the
hob
You can change the behaviour of your extractor hood
in the basic settings of your hob, depending on switch-
on/off of the hob or individual cooking zones.
You can select other settings using the controls on the
hob.
Setting the fan
1. Touch ⁠.
2. Use the twist knob to select a fan setting.
You can choose between the levels 1, 2 and 3.
To select an intensive setting, turn the twist knob un-
til ⁠ ⁠ or ⁠ ⁠ appears.
Switching off the fan
▶Use the twist knob to select the fan setting 0.
Switching on automatic mode
1. Touch ⁠.
2. Turn the twist knob until the display shows ⁠.
aThe fan will start automatically when steam is pro-
duced.
Switching off automatic mode
1. Touch ⁠.
2. Use the twist knob to select the fan setting 0.
3. Automatic mode will also end if you select a differ-
ent fan setting.
Setting the hood lighting
You can switch the hood lighting on and off using the
control panel of the hob.
1. To switch the lighting on, touch ⁠.
2. To switch the lighting off, touch ⁠ again.

en Cleaning and servicing
20
21.3 Overview of the hood control settings
In the basic settings for your hob, you can adjust the behaviour of your extractor hood depending on whether the hob
or individual cooking zones are switched on or off.
Setting Selection Description
⁠ ⁠ ⁠ Connection between hob and extractor hood
⁠ – Not connected/disconnected
⁠ – No function
⁠ – Connected to WLAN home network (Wi-Fi)
⁠ – Connected to WLAN and extractor hood
-
⁠ ⁠ ⁠ Automatic fan start-up
⁠ – Switched off. The extractor hood must be
switched on manually, if required.
⁠ – Switched on in automatic mode1. In automatic
mode, the extractor hood switches itself on when
one of the cooking zones is switched on.
⁠ – Switched on in manual mode. The extractor
hood is switched on at a specified setting when a
cooking zone is switched on.
The display shows this setting only when the appli-
ance has been connected to the extractor hood.
⁠ ⁠ ⁠ Fan run-on
⁠ – Fan switches off when the hob is switched off.
⁠ – Switched on in automatic mode1
⁠ – Switched on with standard fan run-on
⁠ – No change to the settings
Setting for whether and how the fan is to run on
after switching off the hob.
The display shows this setting only when the appli-
ance has been connected to the extractor hood.
⁠ ⁠ ⁠ Switching the light on automatically
⁠ – Switched off
⁠ – Switched on1
The light switches itself on when the hob is
switched on.
The display shows this setting only when the appli-
ance has been connected to the extractor hood.
⁠ ⁠ ⁠ Switching the light off automatically
⁠ – Switched off1
⁠ – The light switches itself off when the hob is
switched off.
The display shows this setting only when the appli-
ance has been connected to the extractor hood.
1Factory setting (may vary according to model)
22 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
22.1 Cleaning products
You can obtain suitable cleaning products and glass
scrapers from customer service, a retailer or the online
shop www.neff-international.com.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶Never use unsuitable cleaning products.
▶Do not use cleaning products while the hob is still
hot. This may cause marks on the surface.
Unsuitable cleaning products
¡Undiluted detergent
¡Detergent intended for dishwashers
¡Abrasive cleaning products
¡Aggressive cleaning products such as oven spray
or stain remover
¡Abrasive sponges
¡High-pressure or steam jet cleaners
22.2 Cleaning the hob
Clean the hob after every use to stop cooking residues
from getting burnt on.
Requirement:The hob must be cold. Do not allow the
hob to cool down if it has sugar stains, plastic or alu-
minium foil on it.
1. Remove heavy soiling using a glass scraper.
2. Clean the hob with a cleaning agent for glass
ceramic.
Follow the cleaning instructions on the packaging of
the cleaning agent.
Tip:You can achieve good cleaning results using a
special sponge for glass ceramic.
22.3 Cleaning the hob surround
If the hob frame is dirty or stained after use, clean this.
Note:Do not use a glass scraper.
1. Clean the hob frame with hot soapy water and a soft
cloth.
Wash new sponge cloths thoroughly before use.
2. Dry with a soft cloth.