Nemco 6150-24-SL Manual

Operating and Maintenance Instructions
Model series: STRIP HEATERS
6150-24-SL 6150-36-SL 6150-48-SL 6150-60-SL 6150-72-SL
ALTERNATE VOLTAGES: 208V/240V
6150-24-DL 6150-36-DL 6150-48-DL-240 6150-60-DL-240 6150-72-DL-240
ALTERNATE VOLTAGES: 208V/240V
NOTE: MODEL SERIES 6155 IS REMOTE VERSION
1
INTRODUCTION
1. Please read instructions before using this appliance.
2. When using this appliance, basic precautions should always be followed to reduce the risk of fire, electric shock and injury.
3. Clean machine thoroughly before and after all uses following cleaning instructions below.
ELECTRICAL REQUIREMENTS
1. Wire warmer into a grounded circuit with correct voltage and sufficient power capacity. Refer to the product label (serial plate)
on the warmer for voltage and wattage requirements.
2. All electrical connections must be made according to local codes by a licensed electrician.
SAFETY INSTRUCTIONS
1. Warning! All power must be disconnected at power source before any service procedure is performed.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as
drapes and other furnishings, away from appliance.
3. Extreme caution is necessary when any appliance is used by or near children and whenever the appliance is left unattended.
4. Always turn the power off at the circuit breaker before cleaning, adjusting or maintaining this machine.
5. Do not operate any appliance after it malfunctions, has been dropped, or damaged. Return appliance to an authorized service
facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors. This appliance is not intended for use in wet or moist locations. Never locate appliance where it may fall
into water.
7. To prevent a possible fire, it is recommended that the unit is installed above a non-combustible surface.
8. This appliance has electrical parts. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
INSTALLATION
1. All 6150 and 6151 models should be wired per ELECTRICAL REQUIREMENTS above.
2. Use MOUNTING BRACKET supplied with the warmer. Install with the following clearances: 9” min. between end of unit and
any wall, 12” min. between side of unit and any wall, 16” min. between bottom of unit and counter, and 1 7/8” min. between
top of unit and overhead surface.
3. This unit radiates heat when in use therefore we recommend that the unit be installed above a non-combustible surface.
4. A wire leg stand (part number 66099) is available for counter use.
5. Use Only Copper Wire suitable for 90° C (194° F).
6. If warmer fails to work properly when first operated call NEMCO customer service at 1-800-782-6761.
OPERATION
1. Place food products in a pan located directly under the warmer for best results.
2. Turn warmer off when not in use.
CLEANING
NOTE: Proper maintenance plays an important part in the life span and functioning of the warmer.
1. Turn warmer off before cleaning.
2. Do not immerse in water or other liquid. Avoid splashing water into unit.
3. The housing and reflectors are made of anodized aluminum and aluminized steel, which can be kept clean by use of a damp
sponge and soap solution.
TROUBLESHOOTING
No Heat
Check that power switch is turned “ON”.
Check power at heater.
Unit Blows Fuse or Circuit Breaker
Check to make sure circuit is not overloaded.
NEMCO
FOOD EQUIPMENT

NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526
Phone: [phone] Fax: [phone] Toll free: 1-800-782-6761
www.nemcofoodequip.com
2
45818-DL
12-6-2019
NOTE: 6155 SERIES DOES NOT HAVE TOGGLE SWITCH OR PILOT LIGHT
11£ ~(')
..,. . ----1
i ~
C
VI
Et
66723 TERMINAL COVER
(2) FOR DUAL LIGHTED
(l) FOR SINGLE LIGHTED
66722-1 TOP HEATER SUPPORT
66722-2 BOTTOM HEATER SUPPORT
48284, SOCKET, LAMP, SIDE OUTLET
(2) FOR 24"
P) FOR36"
Pl FOR 48"
(4) FOR 60"
(4) FOR 72"
69064-() LIGHT SOCK ET M NT
67764 TERM COVER PLATE
(2) FOR DUAL UG HTED
(1) FOR SINGLE LIGHTED
69066, TOP COVER LIGHTEXT
45380-1 PILOT UGHT, 120V
45781-1 PILOT UGHT, 240V
46377TOGGLE SWITCH, 120V
49196 TOGGLE SWITCH, 240V
69073, END CAP DUAL UG HTED
69071, END CAP SG L LIGHTED
69074, END CAP DUAL LIGHTED
69072, END CAP SGL UGHTED
45758 - () 120V ELEM ENT
48286 - () 208VELEMENT
48283 - () 240V ELEM ENT
66721-() HEATER GUARD
(2) FOR DUAL LIGHTED
(l) FOR SING LE UG HTED
NOT SHOWN :
(2) 69069 HANGER BRACKET DUALUGHTED
(2) 69068 HANGER BRACKET SINGLE
46356 LIGHT BULB , 40 WA TT

NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526
Phone: [phone] Fax: [phone] Toll free: 1-800-782-6761
www.nemcofoodequip.com
3
45818-DL
12-6-2019
WIRE SCHEMATICS
FOR Sl 120 VERSIONS
FOR Sl 208/240 VERSIONS
S\IITCH
_l _o-~---r
_I_ t---~-- ~
HEAIER llGHlS
SWIICH HEAIER llGHrs
_J_ ----~-~
N WJ ITT
G GRttN
7_ G
GR t fN
7_
FOR Dl 208/240 V ERSIONS
S IIT CH
FOR DL 120 VERSIONS
Li ~ _/_ ------------<
S \li 11CH
HEATER HEATER llGHlS
1 2
HEATER HEAHR LIGHTS
1 2
N I\\I IIE
N v.H ITT
G GREIN
7_
G GmN
7_
lntertek