NEO GAS-5BURN-BBQ User manual

Neo 5 Burner (4+1) Gas BBQ with Gas Regulator Kit & Rain Cover
INSTRUCTION MANUAL
GAS-5BURN-BBQ
For any issues please feel free to contact us, we are always happy
to help.
Email: [email protected]
Telephone: [phone]

PARTS
Please see page 2 for detailed part list

SAFETY INSTRUCTIONS
1
1. Read the instruction manual carefully before use and keep for
future reference. Failure to comply with the instructions can result
in death, serious injury or property damage.
2. For outdoor use ONLY! Do not use indoors.
3. Do not use below ground level.
4. The accessible parts can get very hot. Keep small children,
elderly people and animals away from the gas grill. The use of a
grill glove is advised.
5. Do not move the product while it is alight or hot, wait for the
product to cool down fully before moving.
6. Turn off the gas supply at the gas cylinder when the grill is not in
use or after use.
7. Any modification of the product, misuse or failure to follow the
instructions may be dangerous and will void the warranty.
8. Check your gas grill annually for any leaks. Check whether the
hose connections are tight and leak test them each time you
reconnect the gas cylinder.
9. Do not use the gas grill within 1 meter of combustible materials
or surfaces.
10. LP gas cylinders should not be placed directly underneath the
grill.
11. Open the hook of the grill before lighting.
12. Do not leave the grill unattended when it is lit.
13. Be careful when opening the hook, as the hot steam inside is
released upon opening.
14. Do not cover the grill until it has completely cooled down.
15. Do not use aerosols near the grill.
16. Do not store or use petrol or other flammable vapors or liquids
in the vicinity of this gas grill or any other appliance.
17. If you smell gas, turn off the gas supply at the gas cylinder;
extinguish any open flame; open the hood. Stop using
immediately.

2
PART LIST
No. No. Pic. Pic.
Qty Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
A
B
M5*12
screw
G
M3*10
screw
H
M3*10
self-tap screw
C
Top door
pin
D
E
M4*nut
F
M3*nut
Bottom door
pin
1
1
2
4
1
1
1
1
1
2
2
2
2
2
2
2
2
1
2
24
9
1
1
2
1
1
1
1
1
1
1
M4 *8
screw

3
Note: Please do not tighten the screws and nuts until all assembly steps are completed.
Assembly
1. Assemble the left side and right side frame (5&6) to the bottom
shelf (7) with 4pcs M5 screws (B).
M3*10 st x 2
M3 nut x 2
M3 * 10 screw x 2

4
Assembly
2. Assemble the back shelf (9) to the frames with 4 pcs M5
screws (B).
9
B
B

5
Assembly
8
B
B
3. Assemble the front beam (8) to the front of frames with 4pcs M5
screws (B).

6
Assembly
4. Assemble the 4pcs wheels (10&11) to the end of frame legs.
Please note: the 2pcs wheels with breaks(10) will always be on the
same side.

7
Assembly
5. The body (1) will slide into the frame legs with 8 pcs pre-assembled
M5 screws (See detailed pic.). Tighten the screws after the body is
in position.
Thermometer (23) is fixed to the lid using its own screw.
Make sure all 8pcs screws are pre-assembled before sliding.

8
Assembly
6. Right side shelf (14) is assembled to the body with 6 pcs M5
screws (B).

9
Assembly
7. Left side shelf (15) is assembled to the body with 6 pcs M5 screws
(B).

10
Assembly
8. Side burner rotary switch base (16), side burner front plate and
side burner valve (inside shelf front plate) are assembled together
with 2pcs M4 countersunk screws (A).
A

11
Assembly
9a. Side burner (18) is assembled into the side burner shelf with 2
pcs M4 screws (A). Insert the tube to valve connector.
A18

12
Assembly
9b. One end of ignition (19) is assembled to the side burner shelf with
1pc M4 screw (A) and 1pc M4 nut (D). The other end is assembled to
the valve connector.
A

13
Assembly
NOTICE
In order to succeed in lighting the side burner's, make
sure the ignition needle's head is direct at one of the
side burner's gas holes.

14
Assembly
10. Decorated knob (17) is assembled to side burner’s front plate.
Grate (20) is putted on side burner shelf, with 3 legs slotting into the
holes.

15
Assembly
11. Handles (13) are assembled to front doors (12) with 4pcs M4
screws (A).
A

E
16
Assembly
C
12. Doors are assembled to the frames’ front legs with top and
bottom pins (C&E).

17
Assembly
13. Warming grid (2), cooking grids (3) and heat tents (4) are fixed
into the body.

Tighten all screws before use
Assembly completed
18
Assembly
14. Oil cup (21) is assembled to the oil pan.