NERI & HU 759L User manual

0
1
N
E
R
I
&
H
U
PARTS
4x components of metal frame
1x cabinet body
3x drawers
1x shelf
2x hinged cabinet doors
HARDWARE
10x M8x25 Socket Cap Screw 6x M8x10 Socket Cap Screw
16x Pz1x25 Pozidrive screws 4x Rubber O-rings
18x M3x12 Pozidrive screws
YOU WILL NEED
8mm heavy duty Allen Key
Pozidrive screwdriver or cordless drill with appropriate
Pozidrive attachment
2x appropriately sized G-clamps with protective clamping surface
The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at and
stable surface. This will ensure a good nal result. Reverse the
steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove the
packaging carefully to avoid damaging your furniture. Refer to
our information sheet “Unpacking Your Furniture” for details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces such
as wood or stone ooring may damage the furniture if in direct
contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
NOTE 5: When screwing in bolts, tighten well, but be sure NOT TO
OVERTIGHTEN. This can cause the thread to strip thus resulting
in a poor connection.
NOTE 6: While working, be sure connections are ush with no gaps.
ASSEMBLY INSTRUCTIONS
TRUNK TALL CABINET BY NERI&HU
SALES@DELAESPAD A.C O M
DELAESPADA.COM

0
2
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
IMPORTANT! ALWAYS USE GLOVES WHEN HANDLING BRASS PRODUCTS.
Our brass is uncoated to embrace the natural patina that will
develop over time. Never handle brass with your bare hands, as
the oils in your skin will cause the surface to oxidise more
quickly in the areas you touch, highlighting your nger prints.
If you ordered your product in brass, you will nd white gloves
in the supplied hardware box.
INSTRUCTIONS
1) ASSEMBLE METAL FRAME
a) Unpack components and lay them out so they are in the
correct orientation.
b) Assemble the frame by aligning the holes in the
corresponding parts, inserting the relevant screws into each,
and tightening with an Allen Key. Use 2x M8x25 Socket Cap
Screws for the uppermost part of the frame, and 4x M8x10 Socket
Cap Screws for the base of the frame.
IMPORTANT: While you work, use the G-clamps to align the
components at the uppermost part of the frame (as shown below).
It is important to use G-clamps with an appropriate barrier
material to protect the brass.
SALES@DELAESPAD A.C O M DELAESPADA.COM

0
3
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
c) The assembly should now look like this.
2) ATTACH THE FRAME TO THE CABINET BODY
a) Carefully turn over the cabinet body so it is face down on a
clean, soft surface on the oor.
SALES@DELAESPAD A.C O M DELAESPADA.COM

0
4
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
SALES@DELAESPAD A.C O M DELAESPADA.COM
b) Turn over the assembled brass frame and place it onto the
cabinet body, being sure to align the holes in each part.
c) Insert 4x M8x25 Socket Cap Screws through the back of the
brass frame, then place a rubber O-ring onto the end of each
before inserting the screws into the back panel of the cabi-
net body. The rubber O-ring should then sit between the brass
frame and the cabinet body to protect the lacquer from getting
scratched. Tighten with an Allen Key.

0
5
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
SALES@DELAESPAD A.C O M DELAESPADA.COM
d) Insert 2x M8x10 Socket Cap Screws through the black painted
steel base of the metal frame, and 4x M8x25 Socket Cap Screws
into the brass sides of the metal frame, driving all through
the bottom panel of the cabinet body. Tighten with an Allen
Key.
3) PLACE DRAWERS INTO THE CABINET BODY
a) With the help of a friend, carefully turn the cabinet into
its natural upright position and extend the drawer rails.

0
6
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
SALES@DELAESPAD A.C O M DELAESPADA.COM
b) Starting from the lowest drawer, insert each of the three
drawers using the following method. On the underside of each
drawer, align the six pre-drilled holes with the holes in the
drawer rails. Insert six M3x12 pozidrive screws and tighten
using a Pozidrive Screwdriver. Next, gently push the drawer
into the cabinet.

0
7
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
SALES@DELAESPAD A.C O M DELAESPADA.COM
4) PLACE SHELF INTO THE CABINET BODY
a) Determine your preferred height for the shelf and move the
pins on the inside of the cabinet accordingly.
b) Insert the shelf, guiding the grooves on the sides of the
shelf onto the pins.

0
8
N
E
R
I
&
H
U
ASSEMBLY INSTRUCTIONS CONTINUED
TRUNK TALL CABINET
SALES@DELAESPAD A.C O M DELAESPADA.COM
5) ATTACH DOORS
a) Determine correct placement and orientation for doors by
referring to number markings.
b) Attach doors by inserting the 16x Pz1x25 Pozidrive screws
into the hinges and tightening with the Pozidrive screwdriver.
c) Assembly is now complete and your cabinet is ready for use.