Net World Sports Forza User manual

www.networldsports.co.uk // [phone] // [e-mail]
www.networldsports.com // 1-866-861-9095 // [e-mail]
@NetWorldSports
2 METRE TEAM SHELTER

PARTS LIST
1.
Top side section Left hand
(1x).
Top side section Right hand
(1x).
Bottom side section left hand
(1x).
Panel A
(2x).
Panel B
(2x).
Bottom side section Right hand
(1x).
Seat crossbar A
(6x).
2m Crossbar
(1x).
Seat crossbar support A
(1x).
Seat strut
(1x).
Side section support A
(2x).
Side section support B
(2x).
Ground fixing bracket
(4x).
Crossbar end cap
(2x).
Seat
(4x).
Oval cap
(54x).
Seat strut cap
(2x).
M8 x 65 bolt
(12x)
M8 x 75 bolt
(2x).
M8 x 80 bolt
(2x).
M8 x 100 bolt
(4x).
M8 x 120 bolt
(4x).
M8 x 110 bolt
(26x)
M10 x 20 bolt
(6x).
M8 nuts
(54x).
M10 nuts
(14x).
M8 washer
(100x)
M10 washer
(14x).
39230
39231
39232 39233
39236 39237
39236 39239 39242 39243
39245 39263 39246
39249 39250 39264 39208 39253
39252 39256 39255 39254 38049
38082 38077 38094 38088
M8 x 55
(4x).
38060
39284
M10x60 bolt
(x8).

HANDY EXTRAS
Wrench Ratchet with sockets Rubber mallet
Step ladder
1. Read through the instructions thoroughly before
assembling the shelter
2. Check parts for any defects prior to the
assembly of the shelter
3. ensure a risk assessment is carried out
and due diligence is used prior to assembly
4. Any safety/warning stickers must be
visible at all times
5. Shelter should be anchored at all times
6. Never climb or hang on the shelter.
8. 2 people required for assembly
7. Periodically check shelter and fittings
for damage
2.
Net world sports will NOT be responsible for injury or
damage caused by a poorly anchored shelter.
PLEASE NOTE

3.
Step 1. Assemble sides.
Layout bottom side sections ( 39232 & 39233)
and top side sections ( 39230 & 39231)
using 2x M8x110 (39255) bolts attach the top side
frame section to the bottom side frame section see fig. 1
39230 39231
39232 39233
FIG.1
Secure using M8 nuts (38082) and washers (38094)
Step 2. Fit back to side frame
Locate Panel A (39234) along the back edge of the side frame.
secure in place using M8x110 bolts (39255) and M8 Nuts and washers
See FIG.2
Repeat this for the other side.
Fit side section support A (39245) to the front of the side frame
using M8x65 bolts (39208) and M8 nuts and washers to secure in place
Fit side section support B (39263) to the Back of the side frame using M8x120 bolts (39254)
at the back and M8x65 bolts (39208) on top, secure in place M8 washers and M8 nuts.
see FIG.2a
39255
38094
38082
38082
38094
39255
38094
38094
FIG.2. 39234 FIG.2a.
39245
39263
39208
39208
39254 39208
Repeat this for the other side.

4.
Step 3. fix back panels together
Manoeuver the 2 parts of the shelter together.
Secure in place with M8x110 bolts (39255) M8 washers and nuts.
See fig.3
Fig.3
39255
Step 4. Assemble and fit roof.
layout the 2 remaining panels B (39237)
Butt these up to each other against the longest edge
fix together using 2 M8x110 bolts (39255)
along with M8 nuts and washers.
See fig 4.
Fig.4
39237
39237
Place the completed roof over the top of the
sides and back panels so it is located flush
with the back ensuring the plastic panels are
facing outwards.
secure in place with 8 M8x110 bolts (39255)
and M8 nuts and washers.
See fig.4a
fig.4a

5.
Fit the crossbar (39239) to the front of the shelter
using M8x110 bolts (39255) and M8 wahsers and nuts
see fig.4b Fig.4b
Step 6. Anchor shelter.
We recommend anchoring the shelter to a level concrete surface
no less than 150mm thick.
The shelter should be anchored by a competent and experienced person.
150MM
Once the position of the shelter has been decided slot 2 M10x20 bolts (38049)
Into the back panels of the shelter at the bottom, see Fig.5.
fig.5
38049
fig.5a
Locate 1 ground fixing bracket (39246) over each of the M10x20 bolts securing loosely
with M10 washer 938088 and M10 nut (38077).
Mark the hole positions and remove the fixing plates ready for drilling.
Mark the position of the holes in the side frame ready for drilling.
See fig.5a
mark hole position

6.
Step 5. fit seat crossbars.
Slot 1x M10x20 bolt (38049) into each of the back sections. See fig.6.
38049
fig.6
fig 6a
locate seat crossbar support A (39243) over M10x20 bolts, loosely secure
to the frame with M10 washer (38088) and M10 nut (38077)
and rest at the bottom of the back frame see fig.6a
39243
38077
38088
fig.5b
see Fig.5b
once the holes have been drilled refit the ground fixing plates
over the ground fixing bolt holes and secure with M10 washer (38088) and nut (38077).
once secured tighten the ground fixing bolts (not supplied)

7.
Place seat strut (39242) in front of seat crossbar support A.
Locate 1 end of seat crossbar A (39236) on side frame over
unused hole nearest the back of the shelter and the other end
on the seat strut over the hole nearest the back of the shelter
See fig.6b
fig.6b
39242
39236
Slide the seat crossbar support A up to meet the seat strut
and secure crossbar and seat crossbar support
in place with M8x80 bolt (39252) M8 washer and M8 nut.
Tighten M10 nuts to secure Seat crossbar support.
secure the other end of the seat crossbar to the side frame
with M8x100 bolt (39256) M8 washer and M8 nut.
See fig.6c
fig.6c
Fit the remaining seat crossbar A’s to the shelter
Using M8x100 bolt (39256) M8 washer and M8 nuts
to secure to the side frame and M8x80 bolt (39252) to the seat strut
fig.6d
39252
39256
See fig.6d

8.
Step 6. fit seats.
fig.7.
Place a seat on the seat crossbar with the holes located
over the middle crossbar.
use 2x M10x60 (39284) bolt and M10 washer and M10 nut to secure in place
making sure not to over tighten the bolts, which may distort the shape of the seat.
use M8x55 bolt (38060) and M8 washer and M8 nut to secure the front of the seat.
repeat this for each of the seats, See fig.7 and Fig.7a
Step 7. Fit hole caps.
Gently tap into place crossbar end caps (39249)
Gently tap into place seat strut caps (39264)
Gently tap into place oval caps (39250) into unused bolt holes
39264
39249
39249
39250
Gently tap into place seat bolt plugs
39284 38060