Net World Sports Forza User manual

www.networldsports.co.uk // [phone] // [e-mail]
www.networldsports.com // 1-866-861-9095 // [e-mail]
@NetWorldSports
FLOOR FIXED NETBALL POST

PARTS LIST
Post (x2) Rail connector (x1) Post connector (x1) Floor fix Base (x1)
Hoop (x1) Rubber end cap (x1) M8x16 hex head bolt (x4)
M8 Spring washer (x4)
M10x80 hex head bolt (x2)
M10x20 bolt (x2)
M10x30 Countersunk bolt (x2) M10 lock nut (x6) M10 Washer (X10)
HANDY EXTRAS
Wrench Ratchet Allen Key Rubber mallet
PA45293. PA45230 PA45289
PA45292 PA45288 PA45273 PA38101
PA45172 PA38115 PA38122
PA38133
1.
Spacer (x1)
PA45294
PA45295
PA45296

*IMPORTANT*
1. Read through the instructions thoroughly before assembling.
2. Installation, movement and use of equipment should be carried out under the
supervision of a competent person using due diligence and risk assessment.
3. Take extreme care when installing, moving and lifting components.
4, Check all parts are present with no defects prior to the assembly.
5. Safety/warning stickers on the product must be visible at all times.
6. Never climb or swing on the product
7. We recommend lubricating/greasing the appropriate components (winders,
sockets, inserts, nuts and bolts) to prolong lifespan.
8. Regularly inspect and maintain the equipment to ensure it is safe to use working
correctly and to increase lifespan.
Step 1. Assemble post.
layout out the 2 post sections (PA45293) and the rail connector (PA45230).
Slide the rail connector into one end of a post with 2 pre-drilled holes. Align
both sets of pre-drilled holes and secure in place with 1 M10x80(PA45172)
hex bolt and M10 lock nut (PA38115) using M10 washers (PA38122) in between
and 1 M8x16 hex bolt (PA45273) and spring washer (PA38133). See Fig.1.
Slide the 2nd post on to the rail connector and secure using same method as above.
PA45293
PA45293
PA45172
PA45273
PA45273
PA38133
PA38115
PA38122
PA38115
2.
2 people will be required to fit post to base

Step 2. Fit hoop and End cap.
Slide 2 M10x20 (PA38101) bolts into the channel at 1 end of the assembled post, locate
the hoop (PA45292) over the bolts and choose the required position. Once the Hoop is in position
secure in place with M10 washers and M10 lock nut. Once hoop is attached tap rubber (PA45288)
end cap into place with a rubber mallet. See Fig.2. and Fig.2a
Please note that the net should be attached the hoop at this point.
PA38101
PA38115
Fig.2
Fig.2a
PA45288
3.
Step 3 - Assemble base
Locate the post connector (PA45289) Over the Ground fixing base, aligning the fixing holes.
Secure in place with M10x30 Countersunk bolt (PA45296), M10 washers and M10 nuts. See fig.3.
PA45289
PA45296
Fig.3

Step 4. Fit post.
Fix the ground fixing base to floor using Ground fixing bolts (not provided).
Locate the Spacer (PA45295) over the post connector with channel facing outwards.
Once the Spacer is in place locatethe post over the post connector. Secure in place
with the post and spacer in place using M8x16 hex head bolts M8x16 hex head bolts (PA45273)
and spring washers. See fig.4. And Fig.4a
4.
PA45273
Fig.4a
Fig.4
PA45295