Netvue Vigil User manual

Vigil Camera Quick Guide
Your property guardian at day and night

Warning
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that
this device does not cause harmful interference (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located for operating in conjunction with any
other antenna or transmitter.
FCC ID 2AO8RNI-1900
CE RED
This product can be used across EU member states.

What’s In The Box
Quick Guide
Hex Key
Drilling Template
Drill Bit
X 3
X 3
Mounting Screws Anchors
Antenna Vigil Camera
Power Adapter
Weatherproof Tube
Vigil Camera Quick Guide
Yourproperty guardian at day and night

Installation Guide Catalogue
1. More About Vigil Camera
2. Read Before Installing
3. Set Up with Netvue App
4. Vigil Camera Installation
5. Status Light
P. 1-2
P. 3
P. 4-12
P. 13-20
P. 21

1
More about Vigil Camera
Infrared LEDs Antenna
Light Sensor
Lens
Wi-Fi
Configuration
Button
Ethernet
Cable Port
Power Port
Status Light
Speaker
Microphone
Micro SD Card Slot

Micro SD
Card Slot
How to Insert Micro SD Card
13
2
2
Vigil Camera comes with a built-in card slot which supports up to 128GB
Micro SD card. Once you insert the storage card, the camera will automati-
cally start to record and store videos on the storage card. You can view those
videos in the ‘Replay’ page by clicking the ‘Replay’ button in the ‘Homepage’.
Step 1: Loosen the screws. Take off the cover gently since wires are attaching to it.
Step 2: Insert Micro SD card. Make sure you insert it in the correct direction. The
back of the card should face up.
Step 3: Put the cover back and tighten the screws.

Read Before Installing
1. Keep the Vigil Camera and all accessories out of reach of children and pets.
2. Power supply voltage that is required to operate Vigil Camera should
be DC12V (≥1000mA).
3. The product can only be used in proper temperature and humidity:
Operating temperature: -10°C - 50°C (14°F-122°F)
Operating humidity: 0-95%.
4. Please do not expose the camera lens to direct sunlight.
5. Please do not install the camera to the place that is likely struck by
lightning.
3

Set Up with Netvue App
Please add the Vigil Camera onto your Netvue account through Netvue App
before mounting it outside.
There are two ways of adding Vigil Camera onto Netvue App: Wireless
Connection and Wired Connection.
Wireless connection uses Wi-Fi to connect the camera to the App. It is the
easiest way if the installation spot is close to your router and have a strong
Wi-Fi signal. Please note that thick or insulated wall may weaken the signal
dramatically. Before you decide to choose this connection method, check
the Wi-Fi signal at your installation spot.
Connecting Method
Wireless connection
4

If the Wi-Fi signal strength is weak at your installation spot, the Ethernet
cable connection might be your solution. An Ethernet cable is required
for this connection method. Plug one end of the Ethernet cable into Vigil
Cam, and the other end into the LAN port on your router. Then follow
the in-app instruction to complete the following set up process.
Wired connection
5

Add Camera to Netvue App
6
Download Netvue App
1. Download Netvue App from App Store
or Google Play onto your phone.

7
2. Register an account if you are a new user to Netvue. If you already
have an account, log into your account.

8
3. Tap “+” to add a new device.

9
4. A product list will show up. Choose
‘Outdoor Cameras’ - ‘Vigil Camera’.

10
5. Scan the QR code on the back of the Vigil.

6. Choose a connecting method,
and then follow the in-app instruction to complete
the entire set up process.
11

Now move to Vigil Camera installation.
7. Test the video streaming.
12

Vigil Camera Installation
Check following things before you starting to drill holes on your wall:
1. Vigil Camera has been successfully added to your Netvue
App and is able to stream video.
2. Have planned the cable route. Measured the length of the
power cable and Ethernet cable (if you plan to use Ethernet
connection) you will need.
13

Step 1:
Take off the anti-dust cap. Attach the provided antenna to Vigil Camera.
1
2
14

Step 2:
Find a good installation spot.
7-10 feet (2-3 meters)
We recommend installing the Vigil camera just 7-10 feet (2-3 meter)
above the ground for a better two-way audio experience.
There is a power outlet nearby.
Test whether Vigil camera can stream video smoothly at the spot.
Make sure nothing blocks the camera’s sight.
11'
10'
9'
8'
7'
6'
5'
4'
3'
2'
1'
15