New Age CRL-101 User manual

CRL-101
MANUAL

THANK YOU
Thank you for selecting the CRL-101 the ultimate crawler. This kit is designed to be ready for serious rock crawling action. The instruction manual you are
reading was designed to be easy to follow. Team New Age wants you to enjoy your new crawler. If you come across any problems or need some help getting
through building it , contact your local dealer or us on the internet at www.teamnewage.com
This is a high performance R/C kit, and it requires regular maintenance for best performance. If you don’t do regular maintenance the performance will suffer.
Team New Age has all the necessary parts and accessories available to keep our car performing at its best.
CAUTIONS
Failure to follow this instruction can damage your kit, and cause serious body injury or death. The kit also contains small parts not suitable for small children.
Before Running
*Please read manual with parent or guardian (responsible adult).
Before Operating
*Make sure that all screws and nuts are properly tightened.
*Always use fresh batteries for transmitter and receiver to avoid losing control of the model.
*Make sure no one else is using the same radio frequency as you are using.
*Please confirm the neutral throttle trigger position.
*Please confirm the range of the radio operation
During Running
*Please do not run on a public street, this could cause serious accidents, personal injuries and /or property damage.
*Please do not run near pedestrians or small children.
*Please do not run in small or confined area.
After Running
*Turn OFF receiver first then turn OFF transmitter. This will prevent the car form losing control.
Battery safety
*Please be careful when handling the battery. It will be hot after running. If the wire is frayed, a short circuit can cause a fire.

NEW VERSION
NEW VERSION
OLD VERSION
OLD VERSION

P.1
BODY POST
CHASSIS PLATE
M3x10mm-BHscrew

P.2
ANTENNA MOUNT
BATTERY PLATE
M3x6mm-BHscrew
M3x12mm-BHscrew

BALL END
100mm
BALL END SET
LINKAGE ASSEMBLY
M3x16mm-BHscrew
P3 ORING
P.3

P.4
BALL END
LOCK NUT
M3x16mm-BHscrew
M3
LINKAGE ASSEMBLY
BALL END SET
50mm
P3 ORING

3mm
2mm
WASHER
SHOCK OIL
M3x20mm-BHscrew
SHOCK ASSEMBLY
BALL END SET
BALL END
P3
ORING
P.5
OILmax
30#OIL
TO PULL
TO PULL

P.6
M3x6mm-BHscrew
SERVO PLATE UPPER CLAMP
SERVO PLATE BOTTOM CLAMP
SERVO PLATE
SERVO MOUNT
M3x25mm-FMscrew

P.7
PIN 2.5
M3x16mm-BHscrew
PRO BUMPER CAP
PRO BUMPER
PRO BUMPER POST
M3x12mm-BHscrew

P.8
BALL END SET
BALL END SET
P3 ORING
P3 ORING
BALL END SET
P3 ORING
BALL END
130mm
LINKAGE ASSEMBLY
47mm
LINKAGE ASSEMBLY
M3x16mm-BHscrew
M3x25mm-FMscrew

P.9
BALL END SET
BALL END
P3 ORING
M3x16mm-BHscrew
M3
LOCK NUT

BALL END SET
BALL END
P3 ORING M3
LOCK NUT
M3x16mm-BHscrew
P.10

P.11
P3 ORING
BALL END
BALL END SET
M3
LOCK NUT
M3x30mm-BHscrew

P.12
WHEEL SET
M4
LOCK NUT

P.13
M3x3mm-SET
0.8mm
WASHER
PINION GEAR
MOTOR
M3x6mm-BHscrew

M3
FM
screw
M3
BHscrew
BHscrew
M3
BHscrew
M3
M3
BHscrew
GEAR Box
FMscrew
M3
screw
M3
FM
GEAR Box
P.15

M3
BHscrew
P3 Oring
M3
BHscrew
P.16