Nexcom NISE 2100 User manual

NEXCOM International Co., Ltd.
NEXCOM International Co., Ltd.
Published January 2011 www.nexcom.com
Industrial Computing Solutions
Fan-less Computer
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A
User Manual

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. ii NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Contents
Contents
Preface
Copyright ............................................................................................. iv
Disclaimer ............................................................................................. iv
Acknowledgements .............................................................................. iv
Regulatory Compliance Statements ....................................................... iv
Declaration of Conformity...................................................................... iv
RoHS Compliance ................................................................................... v
Warranty and RMA ................................................................................ vi
Safety Information ................................................................................vii
Installation Recommendations................................................................vii
Safety Precautions.................................................................................viii
Technical Support and Assistance........................................................... ix
Conventions Used in this Manual........................................................... ix
Global Service Contact Information......................................................... x
Package Contents..................................................................................xii
Ordering Information ............................................................................xiii
Chapter 1: Product Introduction
Overview ................................................................................................1
NISE 2100/2100A .................................................................................1
NISE 2110/2110A .................................................................................2
Hardware Specifications..........................................................................3
Getting to Know NISE 2100/2110 Series .................................................5
Mechanical Dimensions...........................................................................9
Chapter 2: Jumpers And Connectors
Before You Begin ..................................................................................13
Precautions ...........................................................................................13
Jumper Settings ....................................................................................14
Locations of the Jumpers and Connectors.............................................15
Jumpers..............................................................................................17
Clear CMOS .....................................................................................17
COM3 RS232 RI Pin Power Select .....................................................17
Panel CCFL LVDS Backlight Power Select...........................................18
Connector Pin Definitions ...................................................................19
External I/O Interface - Front Panel....................................................19
USB Ports.......................................................................................19
COM5 Serial Port ...........................................................................19
COM6 Serial Port ...........................................................................20
GPIO Connector.............................................................................20
Status Indicators.............................................................................21
ATX Power On/Off Switch ..............................................................21
External I/O Interface - Rear Panel.....................................................22
9-36V DC Input..............................................................................22
Remote Power On/Off Switch.........................................................22
VGA Port .......................................................................................23
Speaker-out Jack............................................................................23
LAN1 and LAN2 Ports.....................................................................24
LAN3 (NISE 2100/2110 only) and Dual USB Ports............................25

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. iii
Contents
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
COM1 and COM2 Ports.................................................................26
COM3 and COM4 Ports.................................................................27
USB 8-9 Connector ........................................................................27
Internal Connectors..........................................................................28
COM5 Connector ..........................................................................28
COM6 Connector ..........................................................................28
Remote Power On/Off Switch.........................................................29
CPU Fan Connector........................................................................29
Internal Power/HDD/LAN Power/LAN Active LED (RTC Connector) ..30
SMBus Pin Header..........................................................................30
Mic-in Connector...........................................................................31
Power Output Connector...............................................................31
LVDS Connector.............................................................................32
Panel CCFL Connector ...................................................................32
CompactFlash ................................................................................33
Mini-PCIe Slot ................................................................................34
PCI Slot (Low Profile)......................................................................35
Chapter 3: System Setup
Removing the Chassis Cover ................................................................36
Installing a SODIMM .............................................................................37
Installing a Wireless LAN Module ..........................................................39
Installing a SATA Hard Drive (NISE 2100/2100A)....................................41
Installing a SATA Hard Drive (NISE 2110/2110A)....................................44
Installing a SATA DOM ..........................................................................48
Installing a CompactFlash Card .............................................................49
Chapter 4: BIOS Setup
About BIOS Setup.................................................................................52
When to Configure the BIOS.................................................................52
Default Configuration...........................................................................53
Entering Setup......................................................................................53
Legends................................................................................................53
BIOS Setup Utility..................................................................................54
Main ..................................................................................................54
Advanced ...........................................................................................55
Boot ...................................................................................................61
Chipset...............................................................................................63
PCIPnP................................................................................................66
Security ..............................................................................................67
Exit.....................................................................................................68
Appendix A: Power Consumption
Test Configuration ................................................................................69
Power Consumption Measurement.......................................................70
Appendix B: GPI/O Programming Guide
J8 - GPI/O Connector ............................................................................71
GPI/O Programming Sample Code.........................................................71
Appendix C: Watchdog Timer Setting
Watchdog Timer Setting .......................................................................73
ITE8783 WatchDog Programming Guide...............................................74

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. iv NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
Preface
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices
and describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area (domestic environment) is likely to cause harmful interfer-
ence, in which case the user will be required to correct the interference
(take adequate measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable Euro-
pean Union (CE) directives if it has a CE marking. For computer systems to
remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by con-
stantly checking its manual posted on our website: http://www.nexcom.
com. NEXCOM shall not be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use of any product, nor for any
infringements upon the rights of third parties, which may result from such
use. Any implied warranties of merchantability or fitness for any particular
purpose is also disclaimed.
Acknowledgements
NISE 2100/2110 Series is a trademark of NEXCOM International Co., Ltd.
All other product names mentioned herein are registered trademarks of
their respective owners.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vNISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
RoHS Compliance
NEXCOM RoHS Environmental Policy and Status
Update
NEXCOM is a global citizen for building the digital infra-
structure. We are committed to providing green products
and services, which are compliant with European Union
RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment)
directive 2002/95/EU, to be your trusted green partner and to protect our
environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the suf-
fix “(LF)” will be added to the compliant product name.
All new product models launched after January 2006 will be RoHS compli-
ant. They will use the usual NEXCOM naming convention.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vi NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
Warranty and RMA
NEXCOM Warranty Period
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning
on the date of invoice by NEXCOM. HCP series products (Blade Server)
which are manufactured by NEXCOM are covered by a three year warranty
period.
NEXCOM Return Merchandise Authorization (RMA)
?Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
?Customers must collect all the information about the problems encoun-
tered and note anything abnormal or, print out any on-screen messages,
and describe the problems on the “NEXCOM RMA Service Form” for
the RMA number apply process.
?Customers can send back the faulty products with or without acces-
sories (manuals, cable, etc.) and any components from the card, such as
CPU and RAM. If the components were suspected as part of the prob-
lems, please note clearly which components are included. Otherwise,
NEXCOM is not responsible for the devices/parts.
?Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
?Any products returned by NEXCOM to other locations besides the cus-
tomers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one
is basic diagnostic fee and another is component (product) fee.
System Level
?Component fee: NEXCOM will only charge for main components such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistor, capacitor.
?Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
?Replace with 3rd party products if needed.
?If RMA goods can not be repaired, NEXCOM will return it to the cus-
tomer without any charge.
Board Level
?Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistors, capacitors.
?If RMA goods can not be repaired, NEXCOM will return it to the cus-
tomer without any charge.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. vii NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are incon-
sistent with these instructions or the instructions for accessory modules,
contact the supplier to find out how you can ensure that your computer
meets safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the de-
scribed procedures only at an ESD workstation. If no such station is avail-
able, you can provide some ESD protection by wearing an antistatic wrist
strap and attaching it to a metal part of the computer chassis.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufactur-
er. Discard used batteries according to the manufacturer’s instructions.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A grounding strap
• An anti-static pad
Using your fingers can disconnect most of the connections. It is recom-
mended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. viii NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
Safety Precautions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a stable surface during installation. Dropping
it or letting it fall may cause damage.
7. Do not leave this equipment in either an unconditioned environment
or in a above 40oC storage temperature as this may damage the
equipment.
8. The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source is correct before connect-
ing the equipment to the power outlet.
10. Place the power cord in a way so that people will not step on it. Do
not place anything on top of the power cord. Use a power cord that
has been approved for use with the product and that it matches the
voltage and current marked on the product’s electrical range label.
The voltage and current rating of the cord must be greater than the
voltage and current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
13. Never pour any liquid into an opening. This may cause fire or electri-
cal shock.
14. Never open the equipment. For safety reasons, the equipment should
be opened only by qualified service personnel.
15. If one of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
16. Do not place heavy objects on the equipment.
17. The unit uses a three-wire ground cable which is equipped with a
third pin to ground the unit and prevent electric shock. Do not defeat
the purpose of this pin. If your outlet does not support this kind of
plug, contact your electrician to replace your obsolete outlet.
18. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTER-
IES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
19. The computer is provided with CD drives that comply with the ap-
propriate safety standards including IEC 60825.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. ix NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Preface
Conventions Used in this Manual
Warning: Information about certain situations, which if not
observed, can cause personal injury. This will prevent injury to
yourself when performing a task.
Caution: Information to avoid damaging components or losing
data.
Note: Provides additional information to complete a task easily.
Technical Support and Assistance
1. For the most updated information of NEXCOM products, visit NEX-
COM’s website at www.nexcom.com.
2. For technical issues that require contacting our technical support team
or sales representative, please have the following information ready
before calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with
care.
2. Maintenance: to keep the unit clean, use only approved cleaning prod-
ucts or clean with a dry cloth.
3. CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. x
Preface
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Global Service Contact Information
Headquarters
Taiwan
18F, No. 716, Chung-Cheng Rd. Chung-Ho City,
Taipei County 235, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
http://www.nexcom.com.tw
USA
3758 Spinnaker Court,
Fremont, CA 94538, USA
Tel: [phone]
Fax: [phone]
http://www.nexcom.com
France
Z.I. des Amandiers, 17, Rue des entrepreneurs
78420 Carrières sur Seine, France
Tel: [phone]
Fax: [phone]
http://www.nexcom.eu
Germany
Leopoldstrase Business Centre, Leopoldstrase 244 80807
Munich, Germany
Tel: [phone]
Fax: [phone]
http://www.nexcom.eu
Italy
Via Gaudenzio Ferrari 29, 21047 Saronno (VA) Italia
Tel: [phone]
Fax: [phone]
http://www.nexcom.eu
United Kingdom
10 Vincent Avenue, Crownhill Business Centre
Milton Keynes, Buckinghamshire, MK8 0AB
United Kingdom
Tel: [phone]
Fax: [phone]
http://www.nexcom.eu

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xi
Preface
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Japan
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku Tokyo,
Japan 108-0014
Tel: [phone]
Fax: [phone]
http://www.nexcom-jp.com
China-Beijing
Room 301, Block E, Power Creative Building, No. 1
Shangdi East Rd. Haidian Dist., Beijing, 100085, China
Tel: [phone]
Fax: [phone]
http://www.nexcom.cn
China-Shanghai Office
Room 1505, Greenland He Chuang Building, No. 450
Caoyang Rd. Shanghai, 200063, China
Tel: [phone]
Fax: [phone]
http://www.nexcom.cn
China-Nanjing Office
Room 1206, Hongde Building, No. 20 Yunnan Rd.
Nanjing, 210018, China
Tel: [phone]
Fax: [phone]
http://www.nexcom.cn
China-Shenzhen Office
Western Room 708, Block 210, Tairan Industry & Trading Place,
Futian Area, Shenzhen, China 518040
TEL: [phone]
FAX: [phone]
http://www.nexcom.cn

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xii
Preface
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Package contents
Before continuing, verify that the NISE 2100/2110 Series package that you received is complete. Your package should have all the items listed in the follow-
ing table.
Item Part Number Description Qty
1 50311F0110X00 (H)FLAT HEAD SCREW LONG FEI:F3x5ISO+NYLOK NIGP 4
2 602DCD0337X00 (N)NISE2100 CD DRIVER VER:2.0 1
3 60177A0223X00 (N)NISE2100 QUICK REFERENCE GUIDE VER:A 1
4 4NCPF00310X00 (N)TERMINAL BLOCKS 3P PHOENIX CONTACT:1803581 1
5 4NCPF00204X00 TERMINAL BLOCKS 2P PHOENIX CONTACT:1777989 1

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. xiii
Preface
NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
ordering information
The following provides ordering information for NISE 2100/2110 Series.
• Barebone
NISE 2100 (P/N: 10J00210000X0)
- Intel®Atom™ D525 fanless barebone system with DDR3 SODIMM
socket and optional wireless module support (either WiFi or mobile
wireless)
- 19V 65W AC/DC power adapter w/o power cord
(P/N: 7400065009X00)
• Barebone
NISE 2100A (P/N: 10J00210001X0)
- Intel®Atom™ D525 fanless barebone system with DDR3 SODIMM
socket and optional wireless module support (either WiFi or mobile
wireless)
- 19V 65W AC/DC power adapter w/o power cord
(P/N: 7400065009X00)
• Barebone
NISE 2110 (P/N: 10J00211000X0)
- Intel®Atom™ D525 fanless barebone system with DDR3 SODIMM
socket, one PCI expansion, and optional wireless module support
(either WiFi or mobile wireless)
- 19V 65W AC/DC power adapter w/o power cord
(P/N: 7400065009X00)
• Barebone
NISE 2110A (P/N: 10J00211001X0)
- Intel®Atom™ D525 fanless barebone system with DDR3 SODIMM
socket, one PCI expansion, and optional wireless module support
(either WiFi or mobile wireless)
- 19V 65W AC/DC power adapter w/o power cord
(P/N: 7400065009X00)

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 1NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
Chapter 1: produCt IntroduCtIon
Overview
NISE 2100/2100A
Key Features
• Onboard Intel®Atom™ Dual Core D525 (1.8GHz, 1M cache)
processor
• One DDR3 SODIMM socket, DDR3 800, maximum of 2GB
memory module
• 3 x Intel®1000/100/10 Mbps LAN ports (NISE 2100)
2 x Intel®1000/100/10 Mbps LAN ports (NISE 2100A)
• 4 x USB 2.0
Rear: NISE 2100
Front
• 1 x VGA
• 1 x DB15 GPIO connector
• 4 x RS232 and 2 x RS232/422/485 with auto flow control
• One external CF socket
• One external SIM card holder
• 9 ~ 36V DC input
• ATX power mode
Rear: NISE 2100A

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 2NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
NISE 2110/2110A
Front
Rear: NISE 2110
Key Features
• Onboard Intel®Atom™ Dual Core D525 (1.8GHz, 1M cache)
processor
• One DDR3 SODIMM socket, DDR3 800, maximum of 2GB
memory module
• 3 x Intel®1000/100/10 Mbps LAN ports (NISE 2110)
2 x Intel®1000/100/10 Mbps LAN ports (NISE 2110A)
• 4 x USB 2.0
• 1 x VGA
• 1 x DB15 GPIO connector
• 4 x RS232 and 2 x RS232/422/485 with auto flow control
• One external CF socket
• One external SIM card holder
• 9 ~ 36V DC input
• ATX power mode
• 1 x PCI Expansion Slot
Rear: NISE 2110A

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 3NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
Hardware Specifications
Main Board
• NISB 2100 (NISE 2100/2110)
NISB 2100A (NISE 2100A/2110A)
• Onboard Intel®Atom™D525 dual core processor, 1.8GHz, 1M cache
• Intel®ICH8M PCH
Main Memory
• One DDR3 SODIMM socket
• Supports up to 2GB DDR3 800 SDRAM memory module, unbuffered,
non-ECC
Expansion
• NISE 2100/2100A
- One Mini-PCIe socket (for optional WiFi or mobile wireless module)
• NISE 2110/2110A
- 1 x PCI expansion
- One Mini-PCIe socket (for optional WiFi or mobile wireless module)
I/O Interface - Front
• ATX Power on/off switch
• HDD access / Power status LEDs
• 1 x DB15 GPIO connector
• 2 x Serial ports (RS232)
• 2 x USB 2.0 ports
• 1 x CompactFlash socket
• 1 x external SIM card holder
• 2 x antenna holes (for optional WiFi or mobile wireless module)
I/O Interface - Rear
• 9~36V DC input
• 1 x 3-pin connector for remote power on/off switch
• 1 x DB15 VGA port
• 1 x speaker-out jack
• 3 x Intel®GbE LAN ports (NISE 2100/2110)
2 x Intel®GbE LAN ports (NISE 2100A/2110A)
• 2 x USB 2.0 ports
• 4 x Serial ports (2x RS232 and 2x RS232/422/485 with auto-flow con-
trol: isolation protection on COM1 and COM2)
Storage
• 1 x 2.5” SATA HDD drive bay (NISE 2100/2100A)
1 x 2.5” SATA HDD drive bay or optional SATA DOM module - horizon-
tal type (NISE 2110/2110A)
• 1 x external CF socket
Power Requirements
• ATX Power mode
• DC to DC power design onboard, supports 9~36V DC
• Optional 19V, 65W power adapter
Dimensions
• NISE 2100/2100A
195mm (W) x 200mm (D) x 65mm (H) (7.7” x 7.9” x 2.6”)
• NISE 2110/2110A
195mm (W) x 200mm (D) x 90mm (H) (7.7” x 7.9” x 3.5”)
Construction
• Aluminum chassis with fanless design

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 4NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
Environment
• Operating temperature - ambient with airflow:
-5°C to 55°C (NISE 2100/2110)
-20°C to 70°C with industrial grade devices (NISE 2100A/2110A)
(According to IEC60068-2-1, IEC60068-2-2, IEC60068-2-14)
• Storage temperature: -20°C to 80°C
• Relative humidity: 10% to 93% (Non-Condensing)
Certifications
• CE approval
• FCC Class A

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 5NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
Getting to Know NISE 2100/2110 Series
NISE 2100/2100A - Front Panel
CF
Power on/off
switch
HDD LED
Power LED
GPIO
COM5
COM6
Antenna hole for
optional WiFi
SIMUSB
USB
Used to connect USB 2.0/1.1 devices.
CF
Used to insert a CompactFlash card.
SIM
Used to insert a SIM card.
Antenna Hole for Optional WiFi
Used to connect an optional Mini-PCIe WiFi module.
COM5 and COM6
Used to connect RS232 compatible serial devices.
GPIO
The GPIO connector supports 4 digital input and 4 digital output.
Power LED
Indicates the power status of the system.
HDD LED
Indicates the status of the hard drive.
Power On/Off Switch
Press to power-on or power-off the system.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 6NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
Remote Power
on/off switch USB
Speaker-out
COM2
COM4
9V-36V DC Input
Used to plug a DC power cord.
Output for Remote Power On/Off Switch
Used to connect a remote to power on/off the system.
VGA
Used to connect an analog VGA monitor.
Speaker-out
Used to connect a headphone or a speaker.
LAN
Used to connect the system to a local area network.
NISE 2100: LAN1 to LAN3
NISE 2100A: LAN1 and LAN2 only.
COM1
COM3
LAN3
(NISE 2100 only)
LAN1
LAN2
9V-36V
DC Input
VGA
NISE 2100/2100A - Rear Panel
USB
Used to connect USB 2.0/1.1 devices.
COM1 and COM2
Used to connect RS232/422/485 compatible serial devices.
COM3 and COM4
Used to connect RS232 compatible serial devices.

Copyright © 2011 NEXCOM International Co., Ltd. All Rights Reserved. 7NISE 2100, NISE 2100A, NISE 2110, NISE 2110A User Manual
Chapter 1: Product Introduction
NISE 2110/2110A - Front Panel
CF
Power on/off
switch
HDD LED
Power LED
GPIO
COM5
COM6
Antenna hole for
optional WiFi
SIMUSB
USB
Used to connect USB 2.0/1.1 devices.
CF
Used to insert a CompactFlash card.
SIM
Used to insert a SIM card.
Antenna Hole for Optional WiFi
Used to connect an optional Mini-PCIe WiFi module.
COM5 and COM6
Used to connect RS232 compatible serial devices.
GPIO
The GPIO connector supports 4 digital input and 4 digital output.
Power LED
Indicates the power status of the system.
HDD LED
Indicates the status of the hard drive.
Power On/Off Switch
Press to power-on or power-off the system.