Next LITTLE HADBURY 882871 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0844 844 8999
• WARNING: Do not leave the child unattended;
• Please note that all assembly fittings shall aways be correctly tightened and checked regularly;
• Weight of the child the product is the intended up to a max.weight of 15 kg;
• Any additional or replacement parts shall only be obtained from the manufacturer or distributor;
• Do not to use the changing unit when any part is broken ,torn or missing;
• Wall fixings are not included.
• When mat fitted, there must be a maximum gap of 30mm between the mat sides and ends and the barrier sides andends.
•This item should not be dismantled for transportation or storage.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage.
• Do not put hot dishes directly on the surfaces of the item.
• Made from honeycomb board, partical board & MDF with a wood effect finish.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
CARE INSTRUCTIONS
• Made in China.
PRODUCT INFORMATION
• Do not use furniture polish.
• A minimum of two persons is required to assemble this product.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Do not rub or scrub the surface when cleaning.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty.
Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Carefully check that you have all parts before beginning assembly.
• Be aware of the risk of open fire and other sources of strong heat,such as electric bar fires,gas fires etc.in the vicinity of the
changing unit;
• Please do not apply adhesive substrates for example , sticky tape to the product.
• We recommend that the packaging is used to protect the surfaces during assembly.
• For general cleaning, periodically dust with a soft cloth.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• The changing unit requires a changing mat measuring a maximum width of 510 mm / length of 740mm and thickness of 30mm.
882871 LITTLE HADBURY CHANGING STATION
882871 LITTLE HADBURY CHANGING STATION882871 LITTLE HADBURY CHANGING STATION
882871 LITTLE HADBURY CHANGING STATION
Page 1 of 11

1. Attach panels 11, 14 & 12 to panel 13 with 6 x screws (F)
and tighten with a screwdriver.
PARTS
CHANGE STATION- STEP ONE
FITTINGS
Page 2 of 11

1. Slide panel 15 into the assembled unit as shown in
diagram.
1. Insert 3 x cambolts (D) into panel 16 and tighten with a
screwdriver.
2. Glue and insert 5 x wooden dowels (B) into panels 11, 12 &
14 and attach panel 16 to panels 11 ,12 & 14.
3. Insert 3 x camlocks (E) into panels 11, 12 & 14 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Attach panel 19 to panels 20 & 21 with 6 x screws (F) and
tighten with a screwdriver.
2. Glue and insert 6 x wooden dowels (B) into panels 22(x2)
and attach panel 22(x2) to panels 20 & 21.
STEP TWO
STEP THREE
STEP FOUR
Page 3 of 11

1. Glue and insert 6 x wooden dowels (B) into panels 22(x2)
and attach panels 17 & 18 to panels 22(x2).
2. Attach panels 17 & 18 to panel 19 with 6 x screws (F) and
tighten with a screwdriver.
3. Attach panel 14 to panel 19 with 2 x screws (F) and tighten
with a screwdriver.
1. Slide panel 15 into the assembled drawer frame.
1. Insert 9 x camlbolts (D) into panel 23 and tighten with a
screwdrive.
2. Glue and insert 9 x wooden dowels (B) into panels 17, 20,
21, 18 & 14 and attach panel 23 to panels 17, 20, 21, 18 & 14.
3. Insert 9 x camlocks (E) into panels 17, 20, 21, 18 & 14 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
STEP FIVE
STEP SIX
STEP SEVEN
Page 4 of 11

1. Insert 6 x camlbolts (D) into panels 1 & 2 and tighten with a
screwdriver.
1. Glue and insert 4 x wooden dowel (A) into panels 3, 4 & 5
and attach panels 3, 4, & 5 to panel 2.
2. Insert 3 x camlocks (E) into panels 3, 4, & 5 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
STEP TEN
1. Slide panel 10 into the assembled frame.
STEP EIGHT
STEP NINE
Page 5 of 11

STEP ELEVEN
1. Glue and insert 4 x wooden dowels (A) into panels 3, 4 & 5
and attach panel 1 to panels 3, 4 & 5.
2. Insert 3 x camlocks (E) into panels 3, 4 & 5 and tighten with
a screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
Note:One person needs to hold panel 1 while the other
person is assembling this item
1. Slide panel 24 into the assembled unit as shown in
diagram.
STEP THIRTEEN
1. Attach 3 x bracket (L) to panel 7 with 6 x screws (M) and
tighten with a screwdriver.
2. Attach panel 7 to panel 9 secure with 6 x screws (M)
through bracket (L) and tighten with a screwdriver .
3. Insert 6 x camlbolts (D) into panel 9 and tighten with a
screwdriver.
STEP TWELVE
Page 6 of 11

STEP FOURTEEN
1. Glue and insert 4 x wooden dowels (A) into panels 1 & 2
and attach panels 7 & 9 to panels 1 & 2.
2. Insert 6 x camlocks (E) into panels 1 & 2 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
STEP FIFTEEN
1. Glue and insert 4 x wooden dowels (A) into panels 8 (x2).
2. Attach panels 8 (x2) to panel 7 with 2 x screws (H) and
tighten with an Allen key (G).
STEP SIXTEEN
1. Glue and insert 4 x wooden dowels (A) into panels 8 (x2).
2. Attach panel 6 to panels 8 (x2) with 2 x screws (H) and
tighten with an Allen key (G) .
Page 7 of 11

STEP SEVENTEEN
1. Attach 3 x metal plate(N) to panels 6 & 9 with 6 x screws
(M) and tighten with a screwdriver.
STEP EIGHTEEN
1. Insert two drawers into the assembled unit as shown in
diagram.
Note: If you want to disassembled the unit, please
follow the steps as the right brief to push the
drawer out.
STEP NINETEEN
1. Insert 8 x plastic fasteners (J) into the back panel grooves
and tighten with screws provided.
2. Use 4 x stickers (K) to cover the holes on panels 6 & 7.
Page 8 of 11

STEP TWENTY
1. Using screw and washer secure the 2 x nylon straps (I) to
the back of panel 7.
2. Move the unit into desired position.
3. Secure the other end of the strap to the wall with an
appropriate screw and wall plug for your wall type (not
provided).To hide the strap behind the unit ,drill the hole
lower than the top of unit.
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires,water and gas
pipes.
NB:Wall fixings are not included-Please source
suitable fixing for your wall type. If in doubt please
consult a qualified trades person.
STEP ONE
1. Untighten screw and remove 2 x the nylon straps (I) from
panel 7 as shown in diagram .
CONVERTING THE CHANGING TO A CHEST
Page 9 of 11

STEP TWO
1. Follow the steps as the right brief to remove the top drawer
.
Note: Please follow the steps as the right brief to
push the drawer out.
STEP THREE
1. Untighten 6 x screws (M) and remove out the 3 x metal
plate (N) from panels 6 & 9 as shown in diagram .
STEP FOUR
1. Untighten 12 x screws (M) and remove out the 3 x bracket
(L) from panels 7 & 9 as shown in diagram .
Page 10 of 11

STEP FIVE
1. Remove the frame as shown in diagram.
STEP SIX
1. Insert the drawer into the assembled unit as shown in
diagram.
STEP SEVEN
1. Using screw and washer secure the 2 x nylon straps (I) to
the back of panel 9.
2. Move the unit into desired position.
3. Secure the other end of the strap to the wall with an
appropriate screw and wall plug for your wall type (not
provided).To hide the strap behind the unit ,drill the hole
lower than the top of unit.
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires,water and gas
pipes.
NB:Wall fixings are not included-Please source
suitable fixing for your wall type. If in doubt please
consult a qualified trades person.
Note: If you want to disassembled the unit, please
follow the steps as the right brief to push the
drawer out.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 11 of 11