NexxTech 4-Way Professional Broadband Signal... User manual

Introduction
The NexxtechTM 4-Way Professional Broadband Signal Amplier
is ideal for distributing a cable signal to a remote location. It
can also distribute antenna and HDTV signals. This amplier
increases the output signal up to 8 dB, while minimizing
interference. It also allows bi-directional communication so you
can enjoy pay-per-view events and interactive TV. It is also
compatible with digital cable modems. The amplier can be
mounted on a wall or placed on a table or other indoor surface.
You can cap off the unused outputs with terminators (not
included) to reduce signal leakage.
Step One: Selecting a Location
Your amplier should be placed close to your input source and
an AC outlet. You can mount the amplier on a wall or other
surface using #6 screws (not included) suitable for mounting in
your location.
• Do not place the amplier outdoors.
• To keep exposed cable to a minimum, you can place the
amplier in your attic.
• To prevent interference, do not place the amplier within
15 cm of any other electronic device.
Step Two: Routing Cables
Route 75 ohm (RG-6 or RG-6QS) coaxial cable from the
amplier to your input source and to each receiver. Follow these
hints when routing cable:
• Use only as much cable as necessary to reach from the
amplier to the input source and receivers.
• Do not route cables where they might be cut, crimped, or
crushed by normal activities.
• For the best appearance, route cable through the attic and
walls, and terminate each cable in a wall mount box with an
F-connector. Wall mount F-connectors, coaxial cable, and other
video accessories are available at your local electronic store.
Step Three: Making Connections
1. Connect a coaxial cable to your input source. To connect
more than one input source, use a high isolation A/B switch or
video selector to switch between inputs.
2. Connect the coaxial cable from your cable box or antenna
(input source) to the amplier’s INPUT terminal.
3. Connect one end of the coaxial cable to an output device and
the other end to an OUTPUT terminal.
4. Attach supplied terminators to unused output terminals.
5. Connect the supplied AC adapter to the jack on the amplier
using the supplied 15 cm RG-6 cable.
6. Plug the AC adapter into a standard AC outlet. The amplier’s
green LED lights when it has power.
7. Turn on every device connected to the amplier.
Notes
• Do not use pliers to tighten screw-on F-connectors.
• Never connect both an outdoor antenna and the output
from the amplier to the antenna input of your TV or VCR
without using a high isolation A/B switch. Doing so could
cause interference with other nearby receivers.
• For an additional grounding method, remove a rubber foot
from the amplier and back out the #6 grounding screw. Place
a grounding wire over the grounding screw and tighten the
screw back into the housing.
• In extremely long cable runs (distances over 60 m), additional
amplication might be needed.
Specications
Forward Path:
Operating Frequency Range .............................. 54 - 1000 MHz
Gain ..................................................................................... 8 dB
Reverse Path:
Operating Frequency Range .................................... 5 - 42 MHz
Insertion Loss ................................................................. -7.5 dB
Adapter Input Voltage ......................................... AC 105 - 135 V
Power Usage ................................................... 12V DC, 200 mA
Power Line Frequency ....................................................... 60 Hz
Dimensions (HWD) ...............................31.75 x 114.4 x 88.9 mm
Weight ............................................................................... 468 g
Specications are typical; Individual units may vary.
Specications are subject to change and improvement without
notice.
Safety Instructions
• Read and retain all the safety and operating instructions.
• This appliance should not be used near water, such as near a
bathtub, washbowl, kitchen sink or laundry tub.
• This amplier should be situated so that its location or position
does not interfere with its proper ventilation.
• This amplier should be connected only to a power supply of
the type described in the operating instructions or as marked
on the amplier.
• Do not attempt to defeat the grounding or polarization
components of this amplier.
• Wipe the amplier with a damp cloth occasionally to keep it
looking new. Do not use harsh chemicals, cleaning solvents,
or strong detergents to clean the amplier.
• The power cord of the amplier should be unplugged from the
outlet when left unused for extended periods of time.
• Do not allow liquids to spill through the amplier’s openings.
• The amplier should be situated away from heat sources such
as radiators, heat registers, stoves or other appliances that
cause heat. Temperature extremes can shorten the life of
electronic devices and distort or melt plastic parts.
• If an outside antenna is connected to a receiver, be sure the
antenna system is grounded to provide some protection
against voltage surges, built-up static charges, and lightning
strikes
• The CATV system installers attention should be given to
proper grounding and, in particular, that the cable ground shall
be connected to the grounding system of the building, as
close to the point of cable entry as practical.
OUTPUT 1, 2, 3, 4 — Connect coaxial cables here to connect
to up to four devices, such as TV, cable modem, or HDTV.
POWER
SUPPLY
INPUT
A
INPUT— Connect
a coaxial cable
here to connect to
your cable system
or antenna.
B
Ground
Screw
Incoming
cable outlet
Wall
Power
Outlet
To TV, Converter,
Modem, etc.
4-Way Professional Broadband Signal Amplier 1512506A

CAUTIONS
You must use a Class 2 power source that supplies 12
VDC and delivers at least 100 mA. Its centre tip must be
set to positive and its plug must t the amplier’s
adapter jack. The supplied adapter meets these specications.
Using an adapter that does not meet these specications could
damage the amplier or the adapter.
Always connect the AC adapter to the amplier before you
connect it to AC power. When you nish, disconnect the adapter
from AC power before you disconnect it from the amplier.
CC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
The FCC Wants You to Know
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
1) reorient or relocate the receiving antenna;
2) increase the separation between the equipment and the
receiver;
3) connect the equipment to an outlet on a circuit different from
that to which the receiver is connected;
4) consult the dealer or an experienced radio/TV technician for
additional suggestions.
Any changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment. Where shielded interface cables have
been provided with the product or specied additional compo-
nents or accessories elsewhere dened to be used with the
installation of the product, they must be used in order to ensure
compliance with FCC regulation.
CAN ICES-3(B)
4-Way Professional Broadband Signal Amplier 1512506A
The Source warrants that this product will be free from defects
in materials and workmanship for a period of ninety (90) days
from the date of purchase. Within this period, simply take the
product and your proof of purchase to any The Source store or
participating dealer and the product will be replaced (where
available) without charge. Any product which has been subject
to misuse or accidental damage is excluded from this warranty.
This warranty is only applicable to a product purchased through
The Source company-owned stores or participating dealers
in Canada where the warranty is included with the product.
While this warranty does not confer any legal rights other than
those set out above, you may have additional statutory rights
which will vary under the laws of the various countries, states,
provinces and other governmental entities in which The Source
operates. This warranty is subject to all statutory rights you may
have in Canada.
© 2013 The Source
All rights reserved.
Imported by:
The Source,
Barrie, Ontario, Canada, L4M 4W5
Manufactured in China
For product support please visit
www.thesource.ca
Please Recycle
THE SOURCE – WARRANTY
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Safety Instructions
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.