Night & Day Pelican Twin Bunk Bed User manual

Page 1 of 8
N&D 0307
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
TM
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Replacement Parts:
Replacement parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
SAFETY WARNING
!
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" width and 74"-75" long on upper bunk (twin size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is at
least 5" (127mm) below upper edge of guardrails.
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.

Parts in Box 3
Parts in Box 2
Parts in Box 1
1A
Page 2 of 8
Hardware in this Box.
1B
N&D 0307
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Tools required for assembly:
Allen Key (supplied)
Phillips Screwdriver
(not supplied)
•
•
Upper Bunk
(Left Hand) x 1 Upper Bunk (Right Hand) x 1
Lower Bunk x 1 Lower Bunk x 1
Set of Slats x 2
Bottom Stretcher x 2
Upper Stretcher
(with extra holes) x 1
Rear Guard Rail x 1
Front Guard Rail x 1
Ladder x 1
Note: No Holes!
Upper Stretcher x 1
Brackets x 4
Long Allen Key x 1
30mm Bolts x 2Wood Dowels x 25 Barrel Nuts x 19
30mm Wood
Screws x 36 16mm Wood
Screws x 2
40mm Threaded
Wood Bolts x 8
100mm Bolts x 19 80mm Bolts x 16 Metal Tubes x 4

Page 3 of 8
Use 2 People!
Please Note:
Be sure the holes are free of wood chips
and saw dust.
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
Attach Stretchers to Lower Frame.
2B Using 100mm Bolts and Barrel Nuts provided with the Lower Frame,
attach the Lower Frame to the Stretchers as shown.
Fit Wood Dowels to the
Stretchers.
2A N&D 0905
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Barrel Nuts
100mm
Bolts
100mm
Bolts
Lower Frame
Lower Frame
Stretcher
Barrel Nuts
100mm
Bolts
Barrel Nuts
Wooden Dowels
Stretcher
Middle
holes

Fit Slats between the Stretchers.
Page 4 of 8
Lay the Slats inside the Stretchers as shown below,and
Bolts in place with 40mm Threaded Wood Bolts
(total 4 Bolts)
3A N&D 0307
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Use the 30mm Wood Screws to fix the
remainingslats to the Stretchers
(total 18 screws.) An electric screwdriver
will make this much easier.
Fix the Remaining Slats with screws.
3B
Stretcher
Lower Frame
40mm Threaded
Wood Bolt
Wood Screws
Wood Screws
40mm Threaded
Wood Bolt 40mm Threaded
Wood Bolts
Wood Screws
Wood Screws

Be sure the holes are free of wood chips
and saw dust.
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
Use 2 People!
Please Note:
Tap Wooden Dowels into the ends of the Stretchers and Rear
Guard Rail. Using 100mm Bolts and Barrel Nuts, attach these to
the Upper Bunk, carefully noting Left and Right hand sides.
Attach the Stretchers and Rear Guard Rail to the Upper Bunk.
4A N&D 0905
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Page 5 of 8
Barrel
Nuts
Rear Guard Rail
Front Stretcher
with Extra Holes
Upper Bunk
Left Hand
Barrel
Nuts
Upper Bunk
Right Hand
Note:
Extra Holes
Note: No
Holes Here! 100mm
Bolts
100mm
Bolts
100mm
Bolts
100mm
Bolt
Wooden
Dowel
Wooden
Dowels
Wooden
Dowels

Tap Wooden Dowels into the ends of the Front Guard Rail.
use the 100mm Bolts and Barrel Nuts fix it in place. The
Front Guard Rail attaches
to the Stretcher using
the 30mm Bolts.
Page 6 of 8
5A Attach Front Guard Rail to the Upper Bunk. N&D 0307
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Lay the Slats inside the Stretchers as shown below, and
Bolt in place with the 40mm Threaded Wood Bolts
(total 4 Bolts.)
5B Bolt the Slats to the Stretchers.
Use 2 People!
Please Note:
Front
Guard Rail
40mm Threaded
Wood Bolts
40mm Threaded
Wood Bolts
30mm Wood
Screws 30mm Wood
Screws
30mm Wood
Screws
Wooden
Dowels
100mm
Bolt
Front Guard Rail
Barrel Nut
30mm
Bolts
Front
Guard Rail Stretcher

Use 2 People!
Please Note:
Fit the Metal Tubes into the tops of the legs. Carefully Lift the Top
Bunk onto the Lower Bunk.
6A Fit the Upper Bunk onto the Lower Bunk. Fit the Brackets to the Legs.
6B
Page 7 of 8
Use the 80mm Bolts to fix the Brackets to
the Legs.
N&D 0905
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Metal Tubes
Metal Tubes
80mm
Bolts
80mm
Bolts

7A Attach the Ladder to the Upper Stretcher.
Page 8 of 8
N&D 0905
Pelican Twin Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Finally, hook the Ladder onto the Upper
Stretcher. Use the 16mm Wood Screws
to fix the Ladder in place.
Please take note of the warnings shown on page
one of these instructions, printed on the carton
box and on stickers on the Bunk bed.
•
Ladder
Stretcher
16mm
Wood Screws