Winners Only TI-AP4257-G User manual

57” PEDESTAL TABLE TOP
TI-AP4257-G, T1-SF4257-C, T1-VT4257-G
PARTS LIST
T1-VT4257-01
T1-AP4257-01
TBSR-10355BC-CNNNWC MADE IN MALAYSIA
PAGE 1 OF 3
T1-VT4257-13
T1-AP4257-13
T1-VT4257-07
T1-AP4257-07
T1-VT4257-07
T1-AP4257-07
T1-VT4257-08
T1-AP4257-08
T1-VT4257-08
T1-AP4257-08
T1-VT4257-18
T1-AP4257-18
T1-VT4257-19
T1-AP4257-19
T1-VT4257-13
T1-AP4257-13
Pedestal Leg
PART NO FIGURE DESCRIPTION QTY
IMPORTANT NOTE : Please keep all hardware parts out of the reach of children.
Pedestal Stand
1 pce
1 pce
1 pce
Mounting Plate
Side Mounting Plate
Table Top
Hardware Pack
4 pcs
1 pce
2 pcs

TI-AP4257-G, T1-SF4257-C, T1-VT4257-G
  57” PEDESTAL TABLE TOP
TBSR-10355BC-CNNNWC MADE IN MALAYSIAPAGE 2 OF 3
STEP 2
NOTE : THE UNIT SHOULD BE ASSEMBLED BY 2 OR MORE PEOPLE.
ASSEMBLY
STEP 1
Hex Nut
Hex Nut
12 pcs
Lock Washer
Lock Washer (Large)
(Large)
12 pcs
Flat Washer
Flat Washer (Large)
Pedestal
Leg
Level Glide
(Large)
12 pcs
Lock Washer
(Small)
8 pcs
Flat Washer
(Small)
8 pcs
Wrench
Wrench
1 pce
Allen Key
1 pce
JCBC Bolt
Lock Washer (Large)
Flat Washer (Large)
Wrench
Hex Nut
8 pcs
HARDWARE PART :
Turn the pedestal upside down. Attach legs by inserting
hanger bolts through pre-drilled holes on pedestal.
Put a Flat Washers (Large),Lock Washers (Large) and
Hex Nut onto the hanger bolts then tighten with the
provided Wrench.
STEP 3
Position the table top upside down on a smooth, protective
surface such as carpet. Remove and discard the temporary
Wood Strip. Install the side panel and secure with
Flat Washers (Small), Lock Washers (Small) and
JCBC Bolt. Attach Mounting Plate as shown. Secure
with Flat Washers (Small), Lock Washers (Small) and
JCBC Bolt, then tighten all JCBC Bolts with Allen Key
provided.
Unlock the hooks underneath the table and pull the table top wide
open equally from both ends. Align and attach the table top to the
pedestal. Insert a Flat Washers (Large), Lock Washers (Large)
and Hex Nuts onto the hanger bolts. Tighten all Hex Nuts with the
provided Wrench.
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
Remove Wood Strip
Mounting Plate
Side Panel
Lock Washer (Small)
Flat Washer (Small)
Allen Key
JCBC Bolt
Lock Washer (Small)
Flat Washer (Small)
Allen Key
JCBC Bolt
UnLock
Metal Catches
Must Remove all 4 Cleats
R
E
M
O
V
E
R
E
M
O
V
E

TI-AP4257-G, T1-SF4257-C, T1-VT4257-G
  57” PEDESTAL TABLE TOP
Flip up apron
TBSR-10355BC-CNNNWC MADE IN MALAYSIA
PAGE 3 OF 3
STEP 4
Lift both leaves from the compartment and flip up the aprons then unfold table leaf and place the leaf on the top surface carefully.
Flip down apron
STEP 5
Push table top from both ends to close gap and lock the hooks underneath the table. Adjust the level glides until the table sits firmly.
TO STORE THE CENTRE LEAF WHEN NOT IN USE
Unlock the hooks underneath the table and pull the table top wide open equally from both ends. Flip down the aprons and fold the
centre leaf to store within the compartment. Push table top from both ends to close. Lock the hooks underneath the table.
Level Glide
IMPORTANT NOTE:
Storing and opening the leaf
requires 2 people.
~
UnLock
Metal Catches Lock
Metal Catches
Lock
Metal Catches