Night Watcher NW1200X Installation instructions

1
Motion tracking
sensor led light
Installation & operating manual
NIGHTWATCHER
Model no: n 1200X

2
INTRODUCTION
Congratulations on the purchase of your new Nightwatcher Security Light. Before installation of
the unit, please read the operating instructions and safeguards carefully. It is important that you
read and follow the instructions in the manual, even if you feel you are familiar with this type of
product.
Please retain the instructions in a safe place for future reference
SPECIFICATIONS
Model Number:
NW 200x
AC Input:
220-240V 50Hz
Time Adjustment:
Fixed at 3 Minutes
Sensor Range:
0m x 2 0°
Power Consumption:
8 Watts
IP Weather Rating:
IP55
Light Sour e:
8 x Watt Nichia High Power L.E.D
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL APPLIANCES, IN ORDER TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, AND/OR INJURY, THESE BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED:
FOR YOUR SAFETY
Read all instructions carefully, even if you feel you are quite familiar with the appliance.
• Any alterations or additions to building wiring, must be completed by a licensed electrical
mechanic, or person authorised by legislation to work on the fixed wiring of any electrical
installation
• To prevent electric shock, please ensure that power is disconnected before installing.
• The appliance is not intended for use by children or infirm persons without supervision.
• Children should be supervised to ensure that they do not play with the appliance.
• This unit must be connected to a 220-240V 50Hz power source
• The light must be earthed
• The cable installed shall be 3 x .0mm² at least
• The unit is for outdoor use only
• The unit is for wall mounting
COMPULSORY WARNING
Note: No user serviceable parts inside. Unauthorised modification voids warranty, Return to place of
purchase for replacement or service under warranty.
SAVE THESE INSTRUCTIONS

3
OVERVIEW
IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN.
 This fitting must be earthed.
 Do not mount the luminaire against inflammable surfaces.
 The motion detector will not operate correctly if it is installed:
() Near the outlet of a central heating boiler
() Near air conditioning equipment
() Pointing directly at moving vehicles
() Within sight of reflection from moving water
() Where other lamps could shine onto the detector
NOTE: This highly responsive unit may occasionally activate due to rapid environmental changes. Allow for
approximately 30 seconds warm-
up time before the sensor resumes normal activity.
MOUNTING THE FITTING
To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector.
f
Push-button
3 motion sensors
WARNING ! ! !
BEFORE ATTEMPTING ANY INSTALLATION OR
MAINTENANCE, ENSURE THAT THE
ELECTRICAL SUPPLY IS SWITCHED OFF AND
THE CIRCUIT FUSES REMOVED OR THE
CIRCUIT BREAKER IS IN THE “OFF”POSITION.
TOP VIEW
GOOD SENSITIVITY
LESS SENSITIVITY

4
INSTALLATION AND WIRING INSTRUCTIONS
Remove the inset back mounting box from the luminaire. Fit the inset back mounting box onto the wall and tighten
the screws at a height that ensures adequate coverage of the area by the infrared detector. The minimum
installation height is 2 meters. And the maximum height is 3 meters.
*Please make sure the voltage and polarity are correct before connection. Incorrect voltage may
cause electric shock. If you are not sure, please contact your retailer.
NOTE: DO NOT REMOVE THE SECURING TAPE ON THE FITTING UNTIL THE UNIT IS
FULLY INSTALLED.
WIRING INSTRUCTIONS
 Feed the cable through the back mounting box and bush
the cable entry to avoid abrasion to the cable.
 Connect the earth wire to the connector opposite the
green/yellow cable.
 Connect the red phase conductor active to the connector
opposite the brown cable and tighten the screws.
 Connect the blue neutral conductor to the connector
opposite the blue cable and tighten the screws.
 Check that all connections are correct and tight, as any
misconnections will damage the detector.
 Re-fit the fitting to the back mounting box.
h

5
FUNCTION
This light is equipped with 3 motion sensors: zone covers 60 degree, zone 2 covers 00 degrees and zone 3
covers 60 degrees. 220 degrees (maximum) in total for 3 zones.
 The light will switch on for 3 minutes and off automatically when heat/ movement is detected.
 The factory default: the light on fixed at 3 minutes and works at nighttime.
 To change the mode to nighttime only, push the button at the bottom of the housing and the hidden LED
indicator will turn red under this mode. The light will be on at 3 minutes when detecting any movement at
night.
 Push-button for programmable functions:
- Nighttime mode: light works at night only Push Button
- All day mode: light works on day and night
 Reset function: If the stepper motor of tracking light works abnormal, the hidden LED indicator will flash in red
and the light will stop turning automatically. In All Day mode, the red light will flash for 5 seconds and off for 5
seconds; in Nighttime mode, the red light will flash in regular pattern. Please simply switch off and on the
main power to resume the tracking light. Below are the possible abnormal situations.
- External force: the light head is blocked by objects or is blown by strong wind and is unable to turn properly,
the hidden LED will flash in red to signal users the abnormal situation.
- Stepper motor: when stepper motor is going to be out of its lifetime or is damaged, the hidden LED will flash
in red to signal users the abnormal situation. Please switch off and on the main power, the tracking light
now may or may not resume its operation. If the stepper motor stops working, AEC-933 becomes a
regular motion sensor security light.
Left 70° Right 70°
ZONE 1
ZONE 2
ZONE 3
TOTAL DETECTION RANGE
Hidden LED indi ator

6
OPERATION
. Turn on the wall switch to activate the light, the light is now under Nighttime mode
NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity.
2. To test, walk through the sensor’s detection area.
3. After the light is activated, keep out of dete tion area and the light will switch off automatically after 3 minutes.
The light will be activated again when detecting any movement.
If there is continuing movement in the detection zone, the light will stay on until movement ceases. (after 3
minutes)
NOTE: THE INTELLIGENT MOTION SENSOR TRACKING LIGHT IS DESIGNED TO I LLUMIN ATE WHEN THE DE TECTION
ARE A IS E NTE RED BY A PERSON AND WI LL DE TE CT MOVING HEAT S OURCE. THERE IS NO GUAR ANTEE
IM PLIE D THAT IT WILL PROVI DE TO TAL SECURITY OR PREV ENT ILLEG AL ENTRY.

7
PRODUCT WARRANTY
1 YEAR REPLACEMENT WARRANTY
Your Nightwatcher Security Light is covered for a
Period of 2 months from your
Date of Pur hase.
The Warranty covers faulty parts or workmanship.
The warranty is only made available by
returning the produ t to your point of
pur hase with your re eipt.
PURCHASED FROM:
DATE OF PURCHASE:
PRODUCT SERIAL #:
THIS WARRANTY FORM SHOULD BE
RETAINED BY THE CUSTOMER AT ALL
TIMES.
WARNING
The followin actions will result in the
warranty bein void:
• If the product has been operated on a
supply voltage other than that specified on
the unit
• If the product shows signs of damage or
defects caused by or resulting from
abuse.
• If the product ahs been disassembled or
tempered with in any way.
• If the product is not drilled, mounted and
used in accordance with the instructions.
Note: Warranty excludes consumable parts such
as tubes, globes and batteries.
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT
ALL TIMES. SHOULD YOU HAVE ANY QUESTIONS PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY OR REPAIR
PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:
CUSTOMER SERVICE: 1300 281 005
TO ENSURE A QUICK RESPONSE PLEASE HAVE THE MODEL NUMBER, SERIAL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU
MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.
NEWLITE PTY LTD
E6, 2A Westall Road, Clayton,
Victoria, Australia, 3 68
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.newlitecorp.com.au