Ningbo AS220 Series Guide

1
Electric fireplace with remote control
Models: AS220-XXXX series
AS230-XXXX series
INSTALLATION AND USER
INSTRUCTIONS
Please read all instructions
carefully and retain for
future reference!
Content
Important Safety Instructions ......................2
UNLOAD PACKAGING ..................................3
PLACEMENT.....................................................4
CONTROLS.......................................................4
OPERATING YOUR HEATER ..........................5
CLEANING AND CARE.....................................5
TROUBLE SHOOTING.....................................6
SPECIFICATIONS .............................................6
NINGBO ANKE ELECTRICAL

2
TECHNOLOGY CO., LTD.
NO.300 ZHENXING SOUTH ROAD, SIMEN TOEN,
YUYAO CITY, NINGBO, ZHEJIANG P. R.
CHINA

3
Important Safety Instructions
When using this electrical appliance,basic precautions should be followed to reduce
the risk of fire,electric shock,and injury to person,including the following:
This heater must be used on an AC supply only and the voltage marked on the
heater must
correspond to the supply voltage.
· Do not switch the appliance on until it properly installed as described in this
manual.
· Keep furniture,curtains and other flammable material at least 1 metre away
from the appliance.
· Do not leave the appliance unattended during use.
· Do not leave the appliance unattended whilst connected to the mains supply.
· Keep out of reach of children and do not allow them to operate this appliance.
· This appliance is intended for household use and should not be used for
industrial purposes.
· From time to time, check the cord for damage. Never use the appliance if the
cord or any part of the appliance shows signs of damage.
· Do not operate this appliance with a damaged plug or cord, after a malfunction
or after being dropped or damaged in any way.
· Repairs to electrical appliances should only be performed by a qualified
electrician.
Improper repairs may place the user at serious risk.
· Do not run the mains cable under carpets, rugs etc.
· Do not allow the mains cable to hang over sharp edges or come into contact
with hot surfaces.
· Never immerse the product in water or any other liquids.
· Do not use the appliance outdoors.
· Do not use if you have wet hands.
· Never use the appliance on or near hot surfaces.
· Before cleaning the appliance, ensure it is unplugged from the power and that it
is completely cooled.
· Do not clean the appliance with abrasive chemicals.
· Never use accessories that are not recommended or supplied by the
manufacturer.It could cause danger to the user or damage to the appliance.
WARNINGS:
a) Do not use the heater in reach of a shower, bath or a swimming pool.
b) Heater is not located immediately below a socket-outlet
c) If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
d) In order to avoid overheating, do not cover the heater。

4
e) This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of appliance by a
person responsible for they safely.
f) Children should be supervised to ensure that they do not play with the appliance.
Caution: In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by
the utility.
Always disconnect the heater from the electrical supply before carrying out
cleaning, maintenance. Remove by grasping the plug - do not pull on the cord.
Always use a fireguard when children and infirm persons can come into contact
with the heater.
Never sit or stand on the heater.
UNLOAD PACKAGING
1. open the package
2. take up-protect fiber out
3. take fireplace out (below diagram)
4. find the screw out and fit on the feet .
1
2
4
5
6
3
06
Up -Protect fiber
2
05
fireplace
1
04
feet
4
03
Screw for fit the feet
12
02
Down- Protect fiber
2
01
parking chest
1
serial number
name
quantity

5
→→
⑴⑵⑶
PLACEMENT
This free-standing heater is designed to be placed on a hard, level surface. When
positioning, please keep the following points in mind:
•The fireplace heater must not be located over a fixed electrical socket. The socket must
always be accessible in order to disconnect the heater from the electrical supply for
maintenance or cleaning.
•Keep hearth rugs and other soft furnishings away from the front of the heater. They
could obstruct the free flow of hot air from the fan and damage both soft furnishings
and heater.
CONTROLS
Never cover the heater or obstruct the opening at the base of the heater, this could cause
overheating and, consequently, risk of fire.
Location of Controls
The following switches are located under the controls cover, on the
front of the heater.
123

6
AS220-X10X series AS230-X10X series
Ⅰ
1. Flame dimmer control - Adjust to set flame intensity
2. Heat switch - low heat setting
3. Heat Switch - High heat setting
4. Temperature control
5.The flame adjustment
6. Timing adjustment button
7. Power control button
8. Switch button
This heater must not be located immediately below an socket outlet.
OPERATING YOUR HEATER
•Insert Plug Into Mains Socket
•Open the control panel cover.
•Select the desired function:
For pictureⅠon page 4:
-Flame effect On/Off (1)
-Low Heat 750w (2)
-High Heat 1500w (3)
•It is necessary to switch on the Fan to activate heat functions. Without fan,
heating cannot start.
.

7
AUTOMATIC CUT-OFF
A cut-off switch is fitted to the heating element to prevent damage due to overheating. If
it cuts-off due to an obstruction in the airflow, the heater must be allowed to cool for 15
minutes and the obstruction must be removed before restarting.
Notice: Heater will only work if fan switch is on and thermostat is set above current room
temperature.
CLEANING AND CARE
⚫Before cleaning, always remove the plug from the electrical socket. Ensure that
the unit is cool enough to work on.
⚫Do not use harsh chemicals or solvents to clean this product and avoid using
abrasive cleaning agents.
⚫The heater and glass parts need only to be wiped clean with a dry, soft cloth; do not
use polishes or abrasive materials.
⚫Do not immerse in water or any liquid when you clean it.
⚫Use a slightly damp, lint-free cloth to clean this appliance.
TROUBLE SHOOTING
No heat or light: Check the wall socket by plugging in a working appliance. If socket is
functional, and the cord or plug of the heater is suspected to be faulty, have it checked by an
electrician.
Light but no heat: Check that the Thermostat on the stove is set above the current room
temperature. Alternatively, the automatic cut-off may have engaged - see Automatic Cut-Off
section.
SPECIFICATIONS
POWER SUPPLY: 220 –240V ~ 50Hz
POWER CONSUMPTION: 1400W~1600W
Disposal
Environmental Protection
Waste electrical production should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
NINGBO ANKE ELECTRICAL TECHNOLOGY CO., LTD.
NO.300 ZHENXING SOUTH ROAD, SIMEN TOEN, YUYAO CITY, NINGBO, ZHEJIANG P. R. CHINA