Ningbo GU10 W 5W 120V User manual

MANUALFOR SMART LED BULB
Product name：SMART LED BULB
Model
Rating
Current
(mA)
Base
Power
(W)
GU10 W 5W 120V
120V~
60Hz
70
GU10
5
GU10 CCT 5W 120V
70
GU10 RGB+W 5W 120V
70
GU10 RGB+CCT 5W 120V
70
C37 W 5W E12
70
E12
C37 CCT 5W E12
70
C37 RGB+W 5W E12
70
C37 RGB+CCT 5W E12
70
The products are not designed for use in ：
-For safety reasons, do not open device, doing this will void the warranty.
-Onlyusetheadaptorsupplied; usingaditferentadaptorcandamage thedevice.
- Only use this bulb in a socket that israted for this bulb.
-Thi s device is not designed to be pl a yed with by children like a toy.
-Do not place the device on hot surfaces.
- Before replacing, turn off power and let the bulb cool to avoid electrical shock or burn.
-Risk of electric shock.
-Do not use device where directly exposed to water.
-The device is for indoor use only.
-Do not use the device in wet locations, e.g. bathrooms or outdoors.
While using this product :
-Switch off the power supply to the socket and allow sufficient time for the bulb ta cool before removing
the bulb from the fitting.
-Do not clean the device when itis on and connected to the power supply.
-Remove the water proofing silicone sleeve from outdoor capable bulbs when using themindoors.
-Donot open device, as this will void the warranty.
-To avoid scratching the device, clean only with a soft dry cloth.
-Donot use cleaning agents to clean the device.
CAUTION:
SUITABLE FOR DAMP LOCATION
DO NOT USE WITH DIMMERS
NOT FOR USE IN TOTALLY ENCLOSED LUMINAIRES
THIS LAMP IS NOT INTENDED FOR USE WITH EMERGENCY EXITS
ATTENTION:
ADAPTÉ À L'EMPLACEMENT
NE PAS UTILISER AVEC DES GRADATEURS
NE CONVIENT PAS À DES LUMINAIRES TOTALEMENT FERMÉS
NE CONVIENT PAS AUX SORTIES DE SECOURS
Wireless Specification :
- Wirele ss RF mode frequency band:2412 MHz ~ 2462 MHz
-Wirele ss communications protocol: 802.11b/g/n

Wifi connection Settings
tuyaapp
DOWNLOAD AND INSTALL THEAPP
Search and download "Tuya Smart" , in major
application markets or scan the QR code below to
download the App.
SIGN INAPP
STEP 1 : Sign in with mobile phone number + verification
code.
Select yourcountry code, enter the phone numberand
tap "Get" to get a message contataining verification
code
Enter the verification code in the message and tap
"Login" to login the App.
STEP 2 : Sign in with social media account.
ADD DEVICE-ALLDEVICE
Click"AddDevice” or “+” in theupperrightcornerof the
"My family" page, then click "All Devices" and select
the device(s) to beadded.
…
继续往后做

5017533
CONFORMS TO UL STD. 1993
CERTIFIED TO CSA STD. C22.2 No.1993
FCCID：
2AWECSBULB001
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
MPE caution
To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should
be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
GRACE (NINGBO) SMART TECHNOLOGY CO., LTD
5th Floor, Building 1, No. 255 Chengxin East Road, Panhuo Street, Yinzhou District, Ningbo, Zhejiang, China