Nokia HH-20 User manual

Copyright © 2009-2010 Nokia. All rights reserved.
Nokia Holder Easy Mount HH-20
and CR-118
Issue 1.0 EN
1
E
B
A
C
D

Copyright © 2009-2010 Nokia. All rights reserved.
A
B
C
D
2
E
F
G
345
7
6

Copyright © 2009-2010 Nokia. All rights reserved.
9
810
11

4
Copyright © 2009-2010 Nokia. All rights reserved.
© 2009-2010 Nokia. All rights reserved.
Nokia, Nokia Connecting People and the
Nokia Original Accessories logo are
trademarks or registered trademarks of
Nokia Corporation.
Introduction
The Nokia Holder Easy Mount
HH-20 is a mounting device that
allows you to attach your
compatible mobile holder to the
windscreen or, using the optional
adhesive pad, to the dashboard of
your vehicle.
Read this guide carefully before
installing and using the product.
This product may contain small
parts. Keep them out of the reach of
small children.
General safety instructions
Obey all local laws. Always keep
your hands free to operate the
vehicle while driving. Your first
consideration while driving should
be road safety. Only operate the
mounting device or mobile holder if
it is safe to do so under all driving
conditions.
When you install the mounting
device or mobile holder, ensure that
they do not interfere with or hinder
the steering or braking systems or
other systems used in the operation
of the vehicle (for example, airbags)
or disturb your field of vision while
driving.

5
Copyright © 2009-2010 Nokia. All rights reserved.
Check that the deployment of the
airbag is not blocked or impaired in
any way.
Ensure that the mounting device or
mobile holder is not installed where
you might come in contact with it in
the event of an accident or collision.
Periodically check that the suction
cup at the bottom of the mounting
device is firmly attached to the
windscreen or dashboard, especially
if the ambient temperature changes
a lot.
Never leave the mounting device
inside the vehicle in direct sunlight
or in excessive heat. The mounting
device and suction cup may be
damaged and adhesion may be
impaired if the inside temperature
exceeds +70°C (160°F).
When attaching a mobile holder,
ensure that the display of the
mobile device is clearly visible for
the user. For your safety, install the
holder in the upright position.
Attach to a windscreen
Attach the holder to the
mounting device
To attach the mobile holder to the
mounting device, insert the catch
on the mounting device into the slot
at the back of the holder (see step
1A at the start of this guide). Rotate
the holder clockwise about 90
degrees until it locks into place (1B).
To detach the holder from the
mounting device, rotate it
anticlockwise.

6
Copyright © 2009-2010 Nokia. All rights reserved.
Attach the mounting device to
the windscreen
Before you attach the mounting
device to the windscreen, locate a
safe mounting surface on the
windscreen, and clean the surface
thoroughly with a glass cleaner and
a clean towel. If the ambient
temperature is below +15°C (60°F),
carefully warm the surface and the
suction cup with a hair dryer to
ensure a firm grip on the
windscreen. Ensure that you do not
heat the windscreen excessively to
avoid damage to it.
Press the suction cup of the
mounting device against the
windscreen (1C), and rotate the ring
on the mounting device clockwise
(1D) to create a vacuum between
the suction cup and the windscreen.
Ensure that the mounting device is
firmly attached (1E).
To detach the suction cup from the
windscreen, rotate the ring on the
mounting device anticlockwise (10),
pull the strap located on the edge of
the suction cup (11), and pull the
holder with the mounting device
from the windscreen (12).
Attach to a dashboard
Attach the mounting device to
the dashboard
If the product was supplied with an
adhesive pad, you can attach the
mounting device to the dashboard.
Ensure that the surface where you
attach the adhesive pad on the
dashboard is flat, dry, and free from
dirt and dust.

7
Copyright © 2009-2010 Nokia. All rights reserved.
Peel off the protective sheet from
the adhesive side of the pad (see
step 2A), and press the pad against
the dashboard so that it stays firmly
in place. When you peel off the
protective sheet from the pad, do
not touch the adhesive side.
Press the suction cup of the
mounting device against the pad
(2B).
Turn the catch on the mounting
device to the desired position (2C).
Rotate the ring on the mounting
device clockwise (2D) to create a
vacuum between the suction cup
and the pad.
To detach the suction cup from the
pad, proceed in the same way as
when you detach the cup from a
windscreen (10, 11, and 12).
Attach the holder to the
mounting device
To attach the mobile holder to the
mounting device, insert the catch
on the mounting device into the slot
at the back of the holder (2E).
Rotate the holder clockwise about
90 degrees until it locks into place
(2F). Ensure that the mounting
device is firmly attached (2G).
To detach the holder from the
mounting device, rotate it
anticlockwise.
Place or remove the mobile device
Do not place or remove a mobile
device while driving.
To place your device into the holder,
slide the device into the holder from
the top while you push the latch

8
Copyright © 2009-2010 Nokia. All rights reserved.
(see step 3), and press it against the
bottom of the holder (4). Ensure
that the device is firmly in place (5).
To charge the battery of your device,
use a compatible charger. To attach
the charger cable to the back of the
holder, insert the cable into the
cable support (9), and connect the
charger plug to the charger
connector on your device.
To remove the device, push the latch
(6), hold the sides of the device (7),
and pull the device out from the
holder (8).
Taking care of your device
Your device is a product of superior
design and craftsmanship and
should be treated with care. The
following suggestions will help you
protect your warranty coverage.
• Do not use or store the device in
dusty, dirty areas. Its moving
parts can be damaged.
• Do not drop, knock, or shake the
device. Rough handling can
break fine mechanics.
• Do not use harsh chemicals,
cleaning solvents, or strong
detergents to clean the device.
Only use a soft, clean, dry cloth
to clean the surface of the
device.
• Do not paint the device. Paint
can clog the moving parts and
prevent proper operation.