Norman SmartFit User manual

Installation Instructions
Honeycomb Shade
SmartFit
TM
with frame
SmartFit
TM
Day & Night with frame
SmartFit
TM
with frame SmartFit
TM
Day & Night
with frame
Getting Started
Remove the shade & frame from the package. Save
the packaging until the shade & frame are installed
and working to your satisfaction.
Recommended Tools
 Power drill and drill bit
 Measuring tape
 Screwdriver
 Level
 Pencil
You will need to use the following fasteners for your
particular mounting surfaces:
Surface Fastener
Wood
1 1/2” Screw
2 1/2”Screw
Drywall/
Plaster
WallAnchors, Expansion Bolts
(Not Provide)
Metal
Sheet Metal Screws
(Not Provide)
Check Hardware
2 1/2” Screw Handle
1 1/2” Screw Hoffman Key
Wood Plug (Optional for IB)
Hardware Standard Quantity
Order Width (X) X≦50"
Handle 2 (SmartFit)
4 (SmartFit Day & Night)
1 1/2” Screw
(for L frame with 0.2” light
block and hang strip, OB)
Frame screw hole qty
2 1/2” Screw
(
for L frame with 0.75” light
block & all the Deco
Frames, OB;
for all the L Frames, Hang
strip & all the Z Frames, IB)
Frame screw hole qty
Hoffman Key 4
Wood Plug
(Optional for IB) Frame screw hole qty
Step 1. Assemble the Frame
When OB, take off frame insert from the frame first,
No need to take off frame insert for IB.
And then assemble the frame together with Hoffman
key at the back of the frame.
For frame with T-post, assemble the frames together
first, and then connect the T-post with frame before
installing the frame on window opening.
4 Sides Frame:
L Frame
3 Sides Frame + Sill Plate (optional for Deco Frames
& Z Frames):
Deco Frame
Frame with T-Post (optional for all Frames, except
Hang Strip IB)
L Frame with T-Post:
Z Frame with T-Post:
Front View
Back View
Deco Frame with T-Post:
Step 2. Install the Frame
Outside mount
Place the shade in desired position,
and fix the left-side frame and
right-side frame with one 1 1/2” or 2
1/2” screw respectively.
And then adjust the frame to make
sure the frame is square and the
diagonal line is in the same length.
Secure the rest screws after adjusting the frame to
square.
After all screws are secured, re-attach the frame
insert to the frame.
N300515-2
65101-11743-B
When OB, take off
the frame insert
Use Hoffman Key to
assemble the frame

Inside Mount (when pre-drill option is selected)
Place the shade in desired position, and fix the
left-side frame and right-side frame with one 2 1/2”
screw respectively.
Then adjust the frame to make sure the frame is
square and the diagonal line is in the same length.
Secure the rest screws after adjusting the frame to
square. And attach the wood plus into each screw
hole.
Note: Mounting screws& wood plugs will be
supplied when pre-drill option is selected.
`
Step 3. Install the Shade
Install the Cord Equalizer Housing Cover onto Cord
Equalizer Housing Base which is pre-installed on the
frame, by pushing down the Cover from top of the
notch then slide to the side to match the Base. Make
sure that cords are nice, tight and not tangled.
For child safety, please check and ensure that there
are no loose cords after the shade is completely
installed.
Please also make sure that cords are nice and tight
and not tangled.
For SmartFit:
For SmartFit Day & Night:
Step 4. Handle Installation
Slide the handle onto the plastic piece pre-attached to
the rails.
Adjust the Shade
After the shade is completely installed, use the handle
to raise the shade up to the top and adjust the shade
to level. Then you may operate the shade to any
desired position.
Remove the Shade
Operate the shade to the middle from top and bottom.
Remove the Cord Equalizer Housing Cover from the
Cord Equalizer Housing Base.
Cleaning Instructions
Routine cleaning will help maintain the beauty of your
shade. The shade can be cleaned by using a soft
brush, vacuumed with a low suction hand-held
vacuum, cleaned ultrasonically (specify that a mild
solution must be used and that the head rail should
never be immersed in liquid), or dampen a clean cloth
with a warm water and mild detergent solution to dab
the spot until it’s gone (do not rub!).
For all frames: the installation way is the
same.
Vintage L Frame with valance insert
0.2” light block 0.75” light block
Hang strip Beaded L frame
1.25" Beaded Z Frame 1.5" Bullnose Z Frame
2” Belair Z frame 2" Bullnose Z Frame
3" Crown Z Frame 2” Camber Deco Frame
2” Classic Deco Frame 3" Ridge Deco Frame






Notch
not
Cover
Cord Equalizer
Housing Base
Cord
End Cap
Headrail
Handle
Blanket
End ap
Cord Equalizer
Housing Cover
Bottom
rail
diagonal line for the
frame should be in
the same length












