Humanscale eFloat User manual

Assembly Instructions
North America: [phone]
Europe: [phone]
Asia Pacic: [phone]

2
DESIGNING
HEALTHIER
WORKPLACES

3
Table of Contents
Important Safety Instructions ���������������������������������������������������������������������������������� 4
Before Getting Started��������������������������������������������������������������������������������������������� 6
Parts Included���������������������������������������������������������������������������������������������������������� 6
Assembly Instructions ��������������������������������������������������������������������������������������������� 8
Hand Switch ���������� ����������������������������������������������������������������������������������������������� 10
Trouble Shooting���� ����������������������������������������������������������������������������������������������� 11
Technical Data�������� ����������������������������������������������������������������������������������������������� 11

4
Important Safety Instructions
WHEN USING AN ELECTRICAL FURNISHING, BASIC PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED. READ ALL INSTRUCTIONS BEFORE USING (THIS FURNISHING). HUMANSCALE
CANNOT BE HELD LIABLE FOR INJURY OR DAMAGE CAUSED BY NON-COMPLIANCE WITH
THESE INSTRUCTIONS. SAVE THESE INSTRUCTIONS AND PASSTHEM ON TO ANY FUTURE
USER.
DANGER: To reduce the risk of electric shock always unplug this furnishing from the electrical outlet
before cleaning�
WARNING: To reduce the risk of burns, re, electric shock, or injury to persons:
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or
disabled persons�
• Use this furnishing only for its intended use as described in these instructions� Do not use
attachments not recommended by the manufacturer�
• Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into water� Return the furnishing to a service center
for examination and repair�
• Keep the cord away from heated surfaces�
• Never operate the furnishing with the air openings blocked� Keep the air openings free of lint,
hair, and the like�
• Never drop or insert any object into any opening�
• Do not use outdoors�
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administered�
• To disconnect, turn all controls to the off position, then remove plug from outlet�
WARNING: Risk of Electric Shock - Connect this furnishing to a properly grounded outlet only� See
Grounding Instructions
DO NOT OVERLOAD DESK: To prevent the table from tipping or collapsing, make sure the desk is not
overloaded by the weight of the worksurface and items on table� Evenly distribute load; excess loads
near edges can reduce stability and lead to tip over�
• Worksurfaces must be at least 3/4” (20mm) thick� Work surfaces must not weigh more than
5lbs square/ft� For stability, maximum worksurface size is 36” x 28”�
• Do not exceed maximum load of 90lbs (40�9kg) (110lbs (49�9kg) excluding worksurface)
• For loading always put heavier items in the center and distribute the load�
• Do not sit or stand on table�
USE CARE WHEN OPERATING DESK:
• Before using the table check for any visible signs of damage� Do not use a damaged product�

5
• Make sure no obstacles are in the desk’s path and that the desk is not touching walls or
neighboring objects�
• Items taller than 20” in height should not be placed or stored under the desk�
• Keep Table Frame dry� Keep all electrical components away from water and high humidity� Do
not spray cleaning solutions directly onto table frame�
• Working Temperature for table is 5 - 40OC
• Make sure all the cords are the appropriate length to accommodate the change in height�
• In order to avoid any pinching, please ensure that hand or other body parts are in a safe position
during the operation�
• Unplug power cord during a thunderstorm or if you do not intend to use the desk for a long
time�
• Never use the table if it has a damaged cords or plugs�
• Keep cords away from heated surfaces�
DO NOT OPEN ELECTRICAL COMPONENTS: Do not attempt to service the tables components�
There are no user-serviceable components within the motor control box, hand switch, or table legs� If
your table needs service or you are having issues with your table, please contact customer service�

6
Parts Included
Before Getting Started
• If using a power drill, use a low torque setting�
• Do assemble product on a protective surface�
• 2 or more people maybe required to maneuver the table�
• After assembly the table will need to have initial set up/reset performed before table can be
used�
Leg Column
Power Cord
X Base
1x 4mm Allen Key
Base Plate Power Supply
(5) Cable Ties
(2) Wing Brackets
Hand Switch
(2) Power Supply Straps
Philips Head Screw Driver
2836 Worksurface
Power Drill with Philips driver bit (optional)
Tools Required

7
(6) ST5 X 20 Wood Screws
(4) M6 X 10 Machine Screws
(2) ST5 X 18 Wood Screws (4) ST3�5 X 16 Wood Screws
Hardware Included
(4) M6 X 40 Machine Screws (4) M6 X 14 Machine Screws
(5) ST5 X 16 Wood Screws

8
Secure the Leg to the worksurface using the (6) ST5 X 20mm screws, ensuring that the cords are
at the rear of the worksurface�
Assembly Instructions
Secure the feet to the Leg� Using both the (4) M6 X 14 and (4) M6 X 40 Screws with the 4mm
Allen key
1
2
3
Attach the Wing Brackets to Leg Column using the (4) M4 X 10 screws and 4mm Allen Key�
FRONT

9
Secure the hand switch to the worksurface in your desired location using the (2) ST5 X 18, screw
along the front edge of worksurface� Pilot holes are positioned on the left/right hand side of the
worksurface in our recommended location(s)�
Secure the Power Supply to the worksurface in your desired location using the provided Cable
Straps� To secure the Cable Straps, peel and stick to desired location and secure with the (4) ST3�5
X 16 screws�
Plug the Leg Column into the hand switch� Connect the power supply to the hand switch� Plug the
power cord into the power supply� Use the provided Cable ties to secure cables to underside of
worksurface (not pictured), with either double sided tape or the (5) ST5 X 16 Screws�
4
5
6
Flip your Table right side up and plug into outlet� Reset the desk per instructions in following
section�
YOU MUST RESET THE DESK BEFORE USE. FOLLOW INSTRUCTIONS ON INITIAL SETUP/RESET
UNDER HAND SWITCH
7

10
Hand Switch
Initial Setup / Reset
IMPORTANT:You must RESET the desk prior to use.
1� Press the DOWN button, moving the desk to its lowest position, then release�
2� Hold the DOWN button while the desk clicks lower, slightly rises and stops�
Your desk is now ready to use� The desk base can be adjusted by pressing and holding either the UP/
DOWN button until the desired height is reached�
LED indicator:
Blue - Reset status
Red - Abnormal state
UP DOWN

11
Trouble Shooting
Error Solution
Table does not
move
Ensure all cords are fully secured and the outlet your table is plugged into has
power�
Table moves at a
slow rate Reset table�
Hand Switch
LED Red
Ensure all cables are fully secured� Follow the steps to Reset your table� If you
are still encountering an error please call customer care�
Technical Data
Power supply 100-240VAC 50/60Hz
Maximum input current 1�5A
Stand by power consumption, primarily <0�3W
Operating Temperature 0 - 40C
Height Range 23�4” - 49”
Travel Speed 1” per second (no load)
Noise Level < 50dB
Maximum lift capacity 90lbs (40�9kg) / 110lbs (49.9kg) excluding
worksurface
Duty Cycle 10% Max� 2 min on, 18 mins off

1114 6th Ave, 15th Floor
New York, NY 10036
humanscale�com
For our terms and conditions please go to
https://www�humanscale�com/about/legal-information/terms-conditions�cfm
© 2021 Humanscale Corporation� The text and artwork are copyrighted materials� All rights reserved� The Humanscale mark and logo are
trademarks of Humanscale Corporation and are registered in the United States and certain other countries� GT-NPD-AI-8896-001-R01