Norman SafeNotch Installation and operating instructions

Place the installation brackets at the desired position. Use a level to
ensure all brackets are in alignment.
If supporting brackets are provided. make sure they do not collide with
ladder cords. Use two fasteners (1 1/4” screws or wall anchors) to secure
the installation and supporting brackets.
Step 3. Install the Wand
Step 2. Install the Blind
Recommended Tools
SafeNotch SmartPrivacy
Measuring Tape
Pencil
Level
Screwdriver
Power Drill (1/4” hex driver and drill bit)
Installation & Maintenance Instructions
Check Component / Hardware
You will need to use the following fasteners for your particular
mounting surfaces:
Check your package for contents needed for proper installation.
Getting Started
Supporting
Bracket
N300956
65101-20125
Remove the blind from the package. Be sure to keep the packaging
until the blind operates to your satisfaction. Please take a moment
to review the following installation guide for proper installation.
Cord Cleat
Hardware Standard Quantity
Step 1. Bracket Installation
Outside Mount
Inside Mount
Blind Width (X)
X≦37" 37”<X≦47" 47”<X<60" 60”≦X≦75" 75”<X≦96"
Installation Bracket
Supporting Bracket
1 1/4” Screw for
Bracket
Valance Clip
Valance Return Joinery
(if returns needed)
3/4” Screw for
Cord Cleat
Cord Cleat
3/4” Screw for Hold
Down Bracket
1
2
4
4
1
Hold Down Bracket
(if included)
0
4
1
6
2
8
2
2 3 3 4 4
2
8
3
10
Mounting Surface
Wood
1 1/4" Hexagonal Head Screw (Provided)
Drywall / Plaster Wall Anchors, Expansion Bolts (Not Provided)
Metal
Sheet Metal Screws (Not Provided)
Fastener
Mounting Depth Requirement
Fully Inside Mount
Semi-Inside Mount
(Min.)
2” Blind
2 3/16”
3 15/16”
2.5” Blind
1 11/16”
4 7/16”
Hold Down
Bracket
3/4”&11/4”
Screws
Note: You may find more hardware parts than you actually need. In that case,
feel free to set them aside for future use.
Valance
Return Joinery
Hook the valance clips onto the head rail and space them evenly. Insert wand tilt connector into the bottom of head rail untill it is
clicked.
Please be aware that tilt connector is irremovable from
the head rail once installed.
Step 4. Attach the Valance
Insert the valance return joinery if needed.
Attach the valance and valance returns as below drawing.
Make sure valance clips are not in an obstructive position with the
wand tilter, drum support inside the head rail.
Open the hinged door of the installation brackets and insert the
head rail into the end brackets (and supporting brackets if
provided).
Close the hinged door of the installation brackets.
2"
Valance Clip
Space Evenly
Space Evenly
Installation Bracket
Valance &
Valance Return
Wand
Click !
Wand tilt connector

Hold Down Brackets (optional)
Attach the hold down brackets against a flat surface, horizontally
or vertically, parallel to the bottom rail. Make sure the protruding
area is aligned with the hole on the side of the bottom rail.
Secure the hold down bracket into the bottom rail on both sides to
keep blinds in desired location.
How to Reassemble Cord Release Device
Our blind comes equipped with a cord release device that prevents
child strangulation. Should the cord release device come apart,
please refer to below steps:
1. Align all operating cords and slide them into the slot of cord
release device.
2. Snap cord release device together to close.
Operate the Blind
Additional Attachments
For lowering the blind, the slats need to be in open position.
For raising the blind, gently tilt the slats towards you at 45 degree
first and support bottom rail with your hand while pulling the cord.
Operating Cords
Tilt Wand
Rotate wand to attain desired slat position.
Install the cord cleat on the wall. Wrap the operating cords around
the cord cleat for child safety. Always use the cord cleat to keep
cords out of the reach of children.
!WARNING
Window Blind Cord Can
STRANGLE Your Child
• Children can strangle in the loop
above the cord bead.
• Children can climb furniture to
reach cords.
• Move crib and furniture away.
• Shorten cords to prevent reach.
• Keep cords separate. Twisted or
knotted cords can create a loop.
• Keep all cords out of children’s reach.
• Los niños se pueden estrangular en
el lazo por encima del cordón.
• Los niños pueden subir los muebles
para alcanzar las cuerdas.
• Mueva la cuna y los muebles.
• Acorte las cuerdas para evitar
el alcance.
• Mantenga las cuerdas separadas.
Los cordones retorcidos o anudados
pueden crear un lazo.
• Mantenga todas las cuerdas fuera del
alcance de los niños.
!
ADVERTENCIA
La cuerda de la persiana
puede ESTRANGULAR
su niño
13
16
"
Inside Mount Outside Mount
For Fully Inside Mount, the valance clip needs to be inserted to
the top channel.
For Outside Mount, the valance clip could be inserted
to the bottom channel. Please note when it is at bottom channel, the
height of valance will exceed the head rail by 13/16”.
Cleaning Instructions
Perform periodic simple cleaning of your blind will keep your blind
looking its best for the years to come. There are two ways to clean.
You can dust it with a duster or dusting mitten, or simply use a
soft cloth slightly moisten with lukewarm water to wipe down the
slats.
You can clean it with the blind hanging on the window, or you can
take it down completely. By tilting the slats down but not fully
closed, you will be able to clean most of the top surface of each
slat.
Do not use detergent or abrasive cleaning solutions to clean
the blind since it will likely cause damage to the blind.
Cord Cleat
Tilt
Wand
Operating
Cords
45°
N300956
65101-20125