Nortek Security & Control 2GIG Vario Wireless Receiver User manual

Nortek Security &Control | 1950 Camino VidaRoble, Suite 150 | Carlsbad, CA92008-6517 | USA | 800-421-1587 | www.nortekcontrol.com
Copyright © 2016 Nortek Security &Control LLC.
1
Installation Instructions
Introduction
The 2GIG Vario Wireless Receiver is a flexible unit that can be used either as a
wireless receiver when connected to the security panel or as a stand-alone
receiver, with support for 2GIG sensors.
Main Features
Up to 32 supervised wireless zones
Up to 16 multi-function keyfobs
Two utility outputs
Signal jamming detection
Threshold-level calibration
Tamper detection
Transmitter supervision low battery detection
Low battery detection
Nominal center frequency: 345 MHz
Mounting Considerations
Do not install the receiver close to metal objects and RF generating
devices such as TV sets or computers.
Mount the receiver at a height of at least 1.5 m (5 ft) above the floor.
Wall Mounting
1. Screw cap
2. Upper mounting hole
3. Lower mounting holes (optional)
4. Wall tamper hole
Figure 1. Rear Panel
1. Separate the mounting bracket from the main unit.
2. Use the mounting bracket as a marking template.
3. Tear off screw caps, as needed for covering front screw hole.
4. Mount the bracket to the wall.
Wiring the Receiver
1. Optional screw hole (used to
fasten front and back covers)
2. Red LED
3. Green LED
4. Prog button
5. DIP switch
6. Box tamper
7. BUS connector
8. Terminal block
Figure 2. Receiver Layout (Cover Off)
Terminal
(Left to Right) Description
AUX Red +13.8V power VDC (in BUS connection, connect to
AUX on the control panel)
Com BLK Black 0V common (in BUSconnection, connect to
COM on the control panel)
BUS YEL Data BUS connection (Not for Stand Alone mode)
BUS GRN Data BUS connection (Not for Stand Alone mode)
Relay 1 N.O
For Future UseRelay 1 COM
Relay 1 N.C.
Relay 2 N.O.
For Future Use
Relay 2 COM
Relay 2 N.C.
NOTE: The maximum wire run permitted is 300 meters (1,000 ft)
for the total BUS wiring regardless of the wiring gauge used.
When closing the cover, use a screw cap loated on the rear side to
cover the closing screw.
BUS Mode
(SWB in OFF position)
SW1–SW3 Three switches to set ID of the receiver
SW4–SW6 For Future Use
SW7
Utility Output Receiver Enable/Disable
OFF: Disable
ON: Enable
SW8 For Future Use
DIP Switch Settings
2GIG® Vario System
2GIG Vario Wireless Receiver
10012335 A

Nortek Security &Control | 1950 Camino VidaRoble, Suite 150 | Carlsbad, CA92008-6517 | USA | 800-421-1587 | www.nortekcontrol.com
Copyright © 2016 Nortek Security &Control LLC.
2
LED Description/Condition
Power/BUS
Communication
(RED)
BUS communication between the panel and the
receiver.
Steady: BUS communication OK
Flash: In Program mode or
BUScommunication trouble
Receiver
Communication
Communication between a wireless sensor and
the receiver.
Steady: BUS communication OK
Flash: BUS communication trouble
LED Indications
Programming Steps in the Panel
The following instructions outline the steps required to program the system to
enable wireless expansion using the wireless receiver. For full programming
instructions, refer to the 2GIG Vario System Installation & Programming Guide.
1. Define the receiver ID using DIP switches 1–3. The receiver ID is set to
1 by default.
2. Allocate the receiver to the system (Programming Menu—Quick Keys:
⑦①② ❺).
3. Allocate the relay outputs of the receiver as an output receiver (UO02)
to the system (Programming Menu—Quick Keys: ⑦①②❸).
4. Calibrate the receiver (Programming Menu—Quick Keys: ⑦②❶).
5. Allocate the wireless device (Programming Menu—Quick Keys:
⑦②②).
6. Perform a communication test between the receiver and the device
(Main Menu > Maintenance > Wireless Test).
7. Set the receiver parameters (Zones—Quick Keys ② ① , Keyfobs—
⑧ ② ) and the outputs parameters (Quick Key ③).
NOTE: Multiple receivers can be allocated to the panel.
2GIG
Nortek Security & Control LLC
1950 Camino Vida Roble, Suite 150
Carlsbad, CA 92008-6517 USA
For technical support in the USA and Canada:
Dial: 855-2GIG-TECH (855-244-4832)
Visit www.nortekcontrol.com or 2gig.com/dealers/
For technical support outside of the USA and Canada:
Contact your regional distributor
Visit www.nortekcontrol.com for a list of distributors in your region
FCC/IC Compliance:
This device complies with FCC Rules and Regulations as a Part 15 device, as
well as Industry Canada Rules and Regulations. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: Changes or modifications to the device may void FCC
compliance.
* For more warranty and compliance information, visit www.nortekcontrol.com.
Limited Warranty
This Nortek Security & Control product is warranted against defects in material
and workmanship of two (2) years. This warranty extends only to wholesale
customers who buy direct from Nortek Security & Control LLC or through
Nortek Security & Control LLC's normal distribution channels. Nortek Security &
Control LLC does not warrant this product to consumers. Consumers should
inquire from their selling dealer as to the nature of the dealer's warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control
LLC for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties for functionality, are valid only until the warranty expires. This
Nortek Security & Control LLC Warranty all other warranties expressed or
implied.
2GIG® Vario System
2GIG Vario Wireless Receiver
10012335 A