North Star LW1200-REVO-PC-RGB User manual

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 1/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
Please read the instructions carefully before installing the product and save for future reference.
Notice
Corrosive and abrasive chemicals will destroy the product. Do not use abrasive or chemicals to clean the fixture, it will
damage the fixture,
Fixture rated to operate at -30 ℃ ~+40 ℃ , Running fixture outside of temperature range will reduce the life span.
Indoor and Outdoor
CAUTION:
Suggested installation and disassembly should be made by professional electrical technician only. This product can’t be
disassembled, the LED(s) are not replaceable, if damaged, it must be destroyed.
Risk of fire! Risk of electric and shock .
Danger ！！！
！！！！！！
！！！
Turn off the power supply before installation, maintenance, and disassembly and repair to avoid SHOCK!
1 、
、、
、 Technical Specification ：
：：
：
1) Light Source ： 36 RGB HP LED
2) Input Voltage ： 100-264 VAC 60HZ
3) Power Consumption ： 36W
4) Beam Angle: 25°
5) IP Rating ： IP65
6) Data Interface ： Standard DMX512
(RS485)
7) Four Control Systems ： Self-Control
Mode/ DMX512 Controller/System
Online controller/ System Offline
controller
8) Color
：
Red, Green, Blue change
continuously to output different
brightness, up to 1,600,0000 colors
9) Function
：
Combine all sorts of
standard DMX512 controller to
display effects, such as flowing,
chasing, jumping, shading and
design.
Wrench
Address screen
2pins shield signal output wire
Power Plug wire
2pins shield signal input wire
2、 Dimensional diagram （ Unitmm ） and main parts

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 2/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
Product and Mounting Dimensions ：
：：
：
Notice: Installation and maintenance
should be completed by qualified
professionals.
Product Installation Instruction ：
：：
：
Refer to the hole distance, see #2.
Dimensional Diagram and
step ①
①①
① of 4. Installation Diagram to drill 4
φ6mm installation holes.
Step ②
②②
② Push the plastic anchor into
installation hole.
Step ③
③③
③ Adjust every DMX address to
achieve desired lighting effect.
Step ④
④④
④ Mount fixture to mounting surface
with self-tapping screw.
Step ⑤
⑤⑤
⑤ Loosen the wrench and adjust the
head’s angle. Lock the wrench.
Step ⑥
⑥⑥
⑥ Connect the signal wire. Make sure
the connector is tightened well to remain
waterproof.
Step ⑦
⑦⑦
⑦ Choose control mode you need
and make the electrical connection.
Step ⑧
⑧⑧
⑧ Connect to power supply.
AB
J
Anchor 4PCS
B
Self-tapping screw 4PCS
A
Accessories listing ：
B
A
SDL-109A-T1 waterproof signal amplifier
ZA0003-001 8 channels DMX512 online controller
16 channels Modem
HSYV
H
G
F
E
I
H
G
A
B
C
D
E
F
J
I
ZA0001-001 8 channels DMX512 offline controller
DMX512 controller
8
Self-tapping screw
Anchor
Dedatched Accessories
Accessories
3 、 Installation accessories
4
、 Installation Diagram
5
76
1
2
4
3
2pins shield signal external wire 1pcs
Signal end cap 1pcs

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 3/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
Self-control Mode Use Manual ：
：：
：
Function Specialty ：
：：
： R, G, B changes to
produce different brightness and 7 colors.
It is Suitable for landscaping and
connecting a few or a single fixture.
Step ①
①①
① Choose the first fixture of the string
as the main light.
Step ②
②②
② Set the second and afterward as
002 (Above steps need to be done during
installation).
Step ③
③③
③ When the signal wire is over 100m,
signal amplifier should be used to enhance
signal and avoid distortion.
Step ④
④④
④ Make sure to use end cap or
waterproof glue on the first and last fixture
Not doing so will cause signal distortion or
dead fixtures.
Step ⑤
⑤⑤
⑤ Connect to power supply.
Remarks: Each string can control 170
fixtures maximum. Overlong distance may
connect with 2 pin signal external wire.
Self-control Mode and Address ：
：：
：
Self-control Mode Correspond Address
Red 513
Green 514
Yellow 515
Blue 516
Purple 517
Black 518
White 519
Color Jumping 520
Color Flashing 521
Color Fad
ing
522
2 pins shield signal external wire
D
3
J
C
4
170# 169#
5
5
4
2#1#
SDL-109A-T1 waterproof signal amplifier
J
Follow-up in series connection product adjust to 002
1
2
other glue stop
Signal wire end cap
C
Accessories listing ：
Address screen
5 、 Self-control mode connection diagram

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 4/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
DMX512 Use Manual ：
：：
：
Function Specialty
：
：：
：
R, G, B changes to
produce different brightness and 16 million
different colors. Suitable for landscaping
and limited quantity of fixtures.
Step ①
①①
① Adjust every DMX address to
achieve desired lighting effect.
Step ②
②②
② When the signal wire is over 100m
(300 feet) a signal amplifier should be used
to enhance signal and avoid distortion.
Step ③
③③
③ Make sure to use end cap or
waterproof glue on the first and last fixture
Not doing so will cause signal distortion or
dead fixtures.
Step ④
④④
④ DMX512 isn’t waterproof ， so it
must be put in a dry location.
Step ⑤
⑤⑤
⑤ After setting DMX512 controller,
use 2 pin signal shield external wire to
connect.
Step ⑥
⑥⑥
⑥ Connect to power supply.
Remarks: Standard DMX512 controller
can control 170 fixtures maximum. Over
long distance it may connect with 2 pin
shielded signal external wire.
5
DMX512 controller
E
C
1
J
1# 2#
6
5
169#
170#
3
C
J
2
D
4
E
D
6、 DMX512 controller connection diagram
Accessories listing ：
Signal wire end cap
SDL-109A-T1 waterproof signal amplifier
2 pins shield signal external wire
Address screen

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 5/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
Controlling System Use Manual
(Offline Control) ：
：：
：
Features
：
：：
：
R, G, B changes to produce
different brightness and 16 million
different colors. SD card contains lighting
effect desired. Fixture is Suitable for
landscaping and complicated lighting
effects.
Step ①
①①
① Adjust each DMX address to
cooperate with the lighting effect desired.
Step ②
②②
② When the signal wire is over
100m, signal amplifier should be used
to enhance signal and avoid distortion.
Step ③
③③
③ Make sure to use end cap or
waterproof glue on the first and last
fixture Not doing so will cause signal
distortion or dead fixtures.
Step ④
④④
④ ZA0001-001 8 channels DMX512
offline controller isn’t waterproof so it
must be in a dry location. Each
connector can control 170 fixtures at
most, 1,360 fixtures altogether. Need
HSYV to connect with next controller.
Step ⑤
⑤⑤
⑤ After setting the controller, use 2
pins shield signal external wire to
connect with the next fixture.
Step ⑥
⑥⑥
⑥ Connect to power supply.
Remarks ：
：：
：
1) Overlong distance of connection may
connect with 2 pin shielded signal
external wire.
2) Please refer to offline controller user
manual for operation and parameters.
HSYV
ZA0001-001 8 channels DMX512 offline controller
Address screen
2 pins shield signal external wire
SDL-109A-T1 waterproof signal amplifier
Signal wire end cap
I
I
I
5
F
1
SD 卡
6
2
4
3
F
F
C
C
1# 2#
170# 169#
DJ
J
D
169#170#
C
D
Accessories and electical listing ：
J
7 、 Controlling System Connection Mode(Offline Connection)
2#1#

1200mm 36 LED RGB Wall Washer
LW1200-REVO-PC-RGB
North Star Lighting, Inc. 2150 Parkes Drive Broadview, IL 60155 6/6
Phone: [phone] Fax: [phone]
www.northstar-lighting.com
Document Control #
Controlling System Use Manual (Online
Control) ：
：：
：
Features
：
：：
：
R, G,B changes to produce different
brightness and 16 million different colors. With
computer, it can change and display lighting
effects freely.
Step ①
①①
① Adjust each DMX address to cooperate
with the lighting effect and wiring method.
(Step ②
②②
② When the signal wire is over 100m, use
signal amplifier to enhance signal and avoid
signal distortion.
Step ③
③③
③ Make sure to use end cap or
waterproof glue on the first and last fixture
Not doing so will cause signal distortion or
dead fixtures
Step ④
④④
④ User responsible for computer
preparation. 16 channels Modem for dry
location only. Each connector can connect 16
offline controllers at maximum, Need HSYV to
connect with next controller.
Step ⑤
⑤⑤
⑤ ZA0001-001 8 channels DMX512 online
controller isn’t waterproof , so it must put in dry
location only ， Each connector can control 170
fixtures,1360s altogether. Need HSYV to
connect.
Step ⑥
⑥⑥
⑥ After setting the controller, use 2 pins
shield signal external wire to connect with next
fixture.
Step ⑦
⑦⑦
⑦ Connect to power supply.
Remarks ：
：：
：
1) Over long distance connections may connect
with 2 pin shielded signal external wire.
2) Please refer to online controller use manual
for operation way and parameter.
16 channels Modem
H
HSYV
Accessories and electical listing ：
8 、 Controlling System Connection Mode(Online Connection)
ZA0003-001 8 channels DMX512 online controller
J
D
C
G
I
Signal wire end cap
SDL-109A-T1 waterproof signal amplifier
2 pins shield signal external wire
Address screen
4
4
3
1
2
7
5
6
1# 2#
G
170# 169#
I
I
DJ
J
D
169#170#
G
2#1#
C
C
H