NOUVOLED Vela 350BSW User manual

350W 17R
Beam Spot Wash 3 in 1

1/ 12
User Manual
PLEASE KEEP THIS MANUAL FOR FUTURE NEEDS

2/ 12
5R
1. Unpacking
Thank you for choosing our products. For your own safety, please read this
manual before installing the device. This manual covers the important information on
installation and applications. Please install and operate the fixture with following
instructions, make sure the power is off before opening the light or repairing.
Meanwhile, please keep this manual well for future needs.
It is made of a new type of high temperature strength of engineering plastics
and cast aluminum casing with nice outlook. The fixture is designed and manufactured
strictly following CE standards, complying with international standard DMX512 protocol.
It’s available independently controlled and linkable with each other for operation. And it
is applicable for large-scale live performances, theater, studio, nightclubs and discos.
350W beam spot wash 3-in-1 fixture which features high brightness and stability.
Please carefully unpack it when you receive the fixture and check whether it is
damaged during the transportation. And please check whether the following items are
included inside the box:
Moving head--------One DMX signal cable-------One
Power cable--------One User manual---------------One
Omega bracket----Two Safety cable-------------One

3/ 12
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could damage
the device. Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore, it is essential that the device
be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this
manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this
would be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning
it. Only handle the power cord by the plug. Never pull out the plug by tugging the
power cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease
gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall
be exclusively replaced by the manufacturer or his service agent or a similar
qualified person in order to avoid a hazard.

4/ 12
3. Key Features
• Voltage: AC90-AC260V 50-60Hz
• Power consumption: 600W
• Light source: Yodn 350W 17R lamp
• Color temperature: 8000K
• Lamp usage life: 1000 to 2000 hours
• Pan:540degree Tilt:270degree
• Color wheel: 13 colours+open
• Fixed Gobo wheel: 14 fixed gobos+open
• Rotation Gobo: 9 rotation gobos+open
• Prism: 2 rotation prisms, 1 round 8 facet prism + 16facet prism and 1 linear 6 facet
prism, with rotation in both direction and can combinate to make better effect
• Beam angel: 2°-38° via ZOOM function
• Strobe: 0.5-9 times/second
• Touch display screen and button control
• Control mode: DMX512, auto, sound active
• DMX Channels: 20/24 two channel mode
• Packing size: 48*48*60 cm
• Gross weight: 23.5 Kg
•Display can change 180 degrees to fit different installation position
•Pan/Tilt with 3 phase motor
•With electronic zoom and focus function

5/ 12
4. Operation Instructions
-The moving head is for beam wash spot purpose.
-Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes.
So, make sure to operate the fixture until it is in normal temperature.
-This light should be kept away from strong shaking during any transportation or
movement.
-Don’t pull up the light by only the head, or it might cause damages to the
mechanical parts.
-Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the
fixture.
-Make sure to put the safety chain and check whether the screws are screwed
properly when installing the fixture.
-Make sure the lens is in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture
before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like shock short circuit, electronic shock,
lamp broke, etc.
5. Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas where the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any surface, make sure that the installation area can
hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment,
such as an appropriate safety cable.

6/ 12
Never stand directly below the device when mounting, removing, or servicing the
fixture from a
periodic safety inspection of all installation material and the fixture. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can
result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the
main power cord to the appropriate wall outlet.
Clamp Mounting: The beam spot wash 3-in-1 provides a unique mounting bracket
assembly that integrates the bottom of the base, the included “Omega Bracket,” and
the safety cable rigging point in one unit (see the illustration below). When mounting
this fixture to truss be sure to secure an appropriately rated clamp to the included
omega bracket using a M10 screw fitted through the center hole of the “omega
bracket”. As an added safety measure, be sure to attached at least one properly
rated safety cable to the fixture using one of the safety cable rigging points
integrated in the base assembly
Regardless of the rigging option you choose for your 10R, always be sure to secure
your fixture with a safety cable. The fixture provides a built-in rigging point for a
safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a
carrying handle.

7/ 12
6. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving heads be connected together through serial linking. The cable needed should be
two core, screened cable with XLR input and output connectors. Please refer to the
diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically
noisy environment, such as in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the digital control signal by electrical
noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected
between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture
in the chain. Please see illustrations below.
1
23
PIN 3
PIN 2
120Ω

8/ 12
7. Display menu control
MENU
Set Up RunMode
DMX
Address
Channel
Factory
DMX
SOUND
AUTO
001-512
20CH
24CH
No Singal Keep
Clean
Screen Saver On
Off
LampOnStart
Info
Factory default
data, don’t change
anything unless it’s
necessary
Pan Reverse
Tilt Reverse
Code Wheel
ON
OFF
ON
OFF
ON
OFF
Advanced
Return
On
Off
Fan Speed
RunTime
On Time
Lamp Hours
Hours
DMX Monitor
Error Log
Return
Current Fan speed
How long has worked this time
How long the fixture has be on
How long the lamp on this time
The rest lifetime of lamp
Show the exact DMX
value of listed function
Manual Manual control of each channel
System error record

9/ 12
8. DMX Channels
20 Channel Mode
CH
Function
DMX Value
Details
1
Pan
0-255
Pan movement
2
Pan fine
0-255
Pan fine
3
Tilt
0-255
Tilt movement
4
Tilt fine
0-255
Tilt fine
5
Pan/Tilt Speed
0-255
Pan/Tilt speed control from fast to slow
6
Strobe
0-3
No function
4-103
Pulse strobe from slow to fast
104-107
Open
108-207
Thunder strobe from slow to fast
208-212
Open
213-251
Random strobe from slow to fast
252-255
Open
7
Dimmer
0-255
Dimmer from dark to bright
8
Color wheel
0-9
Open
10-14
Open mixed with color 1
15-19
Color 1
20-24
Color 1 mixed with color 2
……….
……………
135-139
Color 14
140-149
Color 14 mixed with open
150-203
Color wheel colockwise rotation
204-255
Color wheel anti-clockwise rotation
9
Static gobo wheel
0-5
Open
6-89
Static gobo(Each 6 DMX value is a gobo)
90-134
Gobo wheel clockwise rotation from slow to fast
135-139
Open
140-185
Gobo wheel anti-clockwise rotation from slow to fast
186-255
Gobo shock(Each 5 DMX value is a gobo) slow to fast
10
Rotation gobo wheel
0-8
Open
9-89
Rotation gobo(Each 10 DMX value is a gobo)
90-145
Gobo wheel clockwise rotation from slow to fast
146-155
Open
156-210
Gobo wheel anti-clockwise rotation from slow to fast
211-255
Gobo shock(Each 5 DMX value is a gobo) slow to fast
11
Rotaion gobo
0-64
Rotation
65-127
Anti-clockwise continious rotation from slow to fast
128-191
Clockwise continious rotation from slow to fast
192-255
Rotation like a X
12
Zoom
0-255
Zoom
13
Focus
0-255
Focus
14
6 facet linar prism
0-255
0-127 no function, 128-255 6 facet prism effect
15
6 facet prism rotation
0-64
Rotation
65-127
Anti-clockwise continuous rotation
128-191
Clockwise continuous rotation
192-255
Rotation like a X
16
8+16 Prism
0-255
0-127 no function, 128-255 is 8+16 facet prism effect
17
8+16 facet prism
rotation
0-64
Rotation
65-127
Clockwise continuous rotation
128-191
Anti-clockwise continuous rotation
192-255
Rotation like a X
18
Frost
0-255
0-128 no function, 129-255 is frost effect
19
Uniform spot
0-255
0-127 no function, 128-255 is uniform spot effect
20
Lamp & reset
0-255
0-99 No function, 100-105 Lamp off, 106-199 No function,
200-205 Lamp on, 206-249 No function,250-255 Reset

10 / 12
24 Channel Mode
CH
Function
DMX Value
Details
1
Pan
0-255
Pan movement
2
Pan fine
0-255
Pan fine
3
Tilt
0-255
Tilt movement
4
Tilt fine
0-255
Tilt fine
5
Pan/Tilt Speed
0-255
Pan/Tilt speed control from fast to slow
6
Strobe
0-3
No function
4-103
Pulse strobe from slow to fast
104-107
Open
108-207
Thunder strobe from slow to fast
208-212
Open
213-251
Random strobe from slow to fast
252-255
Open
7
Dimmer
0-255
Dimmer from dark to bright
8
Color wheel
0-9
Open
10-14
Open mixed with color 1
……….
……………
135-139
Color 14
140-149
Color 14 mixed with open
150-203
Color wheel clockwise rotation
204-255
Color wheel anti-clockwise rotation
9
Static gobo wheel
0-5
Open
6-89
Static gobo(Each 6 DMX value is a gobo)
90-134
Gobo wheel clockwise rotation from slow to fast
135-139
Open
140-185
Gobo wheel anti-clockwise rotation from slow to fast
186-255
Gobo shock(Each 5 DMX value is a gobo) slow to fast
10
Rotation gobo wheel
0-8
Open
9-89
Rotation gobo(Each 10 DMX value is a gobo)
90-145
Gobo wheel clockwise rotation from slow to fast
146-155
Open
156-210
Gobo wheel anti-clockwise rotation from slow to fast
211-255
Gobo shock(Each 5 DMX value is a gobo) slow to fast
11
Rotation gobo
0-64
Rotation
65-127
Anti-clockwise continuous rotation from slow to fast
128-191
Clockwise continuous rotation from slow to fast
192-255
Rotation like a X
12
Zoom
0-255
Zoom
13
Zoom fine
0-255
Zoom fine
14
Focus
0-255
Focus
15
Focus fine
0-255
Focus fine
16
6 facet liner prism
0-255
0-127 no function, 128-255 6 facet prism effect
17
6 facet prism rotation
0-64
Rotation
65-127
Anti-clockwise continuous rotation
128-191
Clockwise continuous rotation
192-255
Rotation like a X
18
8+16 Prism
0-255
0-127 no function, 128-255 is 8+16 facet prism effect
19
8+16 facet prism
rotation
0-64
Rotation
65-127
Clockwise continuous rotation
128-191
Anti-clockwise continuous rotation
192-255
Rotation like a X
20
Frost
0-255
0-128 no function, 129-255 is frost effect
21
Uniform spot
0-255
0-127 no function, 128-255 is uniform spot effect
22
No function
0-255
No function
23
Lamp & reset
0-255
0-99 No function, 100-105 Lamp off, 106-199 No function,
200-205 Lamp on, 206-255 No function
24
Reset
0-255
0-249 No function, 250-255 Reset

11 / 12
9. Maintenance and Cleaning
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected
and must not be corroded.
2. There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate
with unbalances.
4. The electric power supply cables must not show any damage, material fatigue or
sediments.
Further instructions depending on the installation spot and usage have to be adhered by
a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a
regular cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakens of the lights due to
accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make
sure that the circuit contacts are in good condition, prevent the poor contact of circuit
from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.
Never use alcohol or solvents. There are no serviceable parts inside the device. Please
refer to the instructions under “Installation instructions”. Should you need any spare
parts, please order genuine parts from your local dealer.