Nova Solutions FPA-0-1621-NK-24 User manual

FRONT EDGE
Dimension A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(32mm)
(Typ.)
W i d e s c r e e n F o r m a t
Figure 1A
Step 1.
Step 2.
The natural way to look at a computer
Figure 1B
PACKING LIST
QTY REF # ITEM # DESCRIPTION
1 A1 100mm *VESA Plate
1 A2 FPA-8-2006 Desk Mount Extension Tube
1 A3 VESA Plate Extension Tube
1 B 014138 Wing Screw
10 C 1412APPBO Screw, #14 x 3/4”, PHP, Black
1 D 20060126 Keyboard Hanger w/ Glide - Left
1 E 20060127 Keyboard Hanger w/ Glide - Right
1 F Varies Keyboard Drawer
1 G 1621 Glass, 16”x 21”
2 H 0149085 Screw, #14 x 1-1/2”, PHP, Black
4 J 0141158 Screw, #6 x 5/8”, PHP, Black
4 K 50900034 Trim Ring Corner
2 L 50900828 Trim Ring Straight - 13“
2 M 50900037 Trim Ring Straight - 18“
4 N 91200 Screw, M4-0.7 x 8mm, PHP, Zinc
Assembly Instructions
This kit ships with a 100mm VESA plate. If all four of the 100mm VESA plate
holes do not line up with the holes on the back of monitor, you may require
a smaller (75mm) VESA plate, which is sold separately. Also available with a
Privacy/Glare Visor (sold separately). Contact Customer Service for more
information.
Cut opening for viewport (Figure 1A). When ordering with a
keyboard, prepare surface for keyboard drawer (Figure 1B).
Using the hole pattern on the Desk Mount Extension Tube
(A2) as a template, locate and drill holes (Figure 1A). Please note
drill size and hole depth.
Flat Panel Display Arm
FPA-0-1621-NK-___
Keyboard Size
-XK for No
Keyboard
Option
Keyboard Size Options: 24 / 28 / 30/ 34
Desk Mount Extension Tube
1.26”
(32mm)
1.26”
(32mm)
A2
” Diameter
” Deep
6 Holes
FRONT EDGE
All corners
3"
(76 mm)
Center on
viewport opening
"
24”
(609.6 mm)
16 ¼”
(413 mm)
21 ¼”
(540 mm)
A2
UNDERSIDE OF TOP CLEARANCE
24” (609.6 mm) minimum clearance depth of worksurface
½” (12.7 mm) R.
Keyboard Drawer Size Dimension A
28”
30”
34”
26 ” (664 mm)
28 ” (715 mm)
32 ” (816 mm)
24” 22 ” (574 mm)
Includes:
Flat Panel Display Arm,
Keyboard Drawer, Glass,
and Trim Ring.
Also Available:
Privacy/Glare Visor
(Sold Separately)
Hole Pattern for Keyboard Drawer
” Diameter
” Deep
6 Holes
P.O. Box 725 • 421 Industrial Avenue • • Phone: [phone] • Fax: [phone] • [e-mail] • www.novadesk.com
FPA-0-1621 Widescreen Asy. Instr. 09/23 Patents Pending Page 1
*VESA 100 Standard

Step 6. Install trim ring & viewport glass
Step 3.
Figure 4
C
H
VESA Plate
Adjustment
D
E
H
C
K
L
M
Figure 5
Step 5
Step 4. Attach Flat Panel Display to VESA plate
Figure 2
A1
A2
N
Back edge of cut-out
Figure 3
100 mm
(3-
15/16")
4-7/16"
100 mm
(3-
15/16")
320°
270°
Monitor Angle
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
B
A3
B
C
A1
Align holes in Desk Mount Extension Tube (A2) with holes in
worksurface (Figure 2) and attach using 6 screws (C). The Flat
Panel Display Arm comes fully assembled.
WARNING: Removing the set screws or oiling the joints
could cause the flat panel display to fall and void the
warranty.
Flat Panel Arm
ships fully
assembled.
Remove flat panel display base. Attach flat panel display to
VESA plate (using screws located on the back of your flat
panel display supplied by manufacturer). See Figure 3
Depress silver spring pin on VESA plate extension tube and
slide it into the desk mount extension tube. Tighten wing
nut (B, Figure 4). See “Monitor Angle” for adjustment
guidance. When installing some Apple® flat panel
displays, a VESA Adapter may be necessary. Contact
Customer Support for more information.
Attach
keyboard
hangers (D, E,
Figure 5) to
underside of worksurface
with screws (C, H).
IMPORTANT: The longer
screws (H) pass through the
tubular section of the
keyboard hanger. That
allows the assembly to be
leveled by loosening or
tightning the screws.
Snap trim ring pieces
(K, L, M) together.
Insert into viewport
cutout and attach with
screws (J). Carefully
insert viewport glass
(G) into trim ring.
Slide Keyboard
drawer into glides
and use locking tabs to
secure in place.
Locking Tab:
Locked when pushed towards user and
unlocked when pushed away.
1. Position screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen
should be closer to eyes than top of screen).
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and raise
flat panel display.
A2
A3
FPA-0-1621 Widescreen Asy. Instr. 09/23 Patents Pending Page 2

FRONT EDGE
Dimension A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(32mm)
(Typ.)
Figure 1A
Step 1.
Step 2.
The natural way to look at a computer
Figure 1B
Assembly Instructions
Cut opening for viewport (Figure 1A). When ordering with a
keyboard, prepare surface for keyboard drawer (Figure 1B).
Using the hole pattern on the Desk Mount Extension Tube (A2)
as a template, locate and drill holes (Figure 1A). Please note drill
size and hole depth.
Flat Panel Display Arm
FPA-0-1818-NK-___
Keyboard Size
-XK for No
Keyboard
Option
Keyboard Size Options: 24 / 28 / 30 / 34
FRONT EDGE
All corners
3"
(76 mm)
Center on
viewport opening
¼"
24”
(609.6 mm)
18 ¼”
(464 mm)
18 ¼”
(464 mm)
A2
UNDERSIDE OF TOP CLEARANCE
24” (609.6 mm) minimum clearance depth of worksurface
½” (12.7 mm) R.
Keyboard Drawer Size Dimension A
28”
30”
34”
26 ” (664 mm)
28 ” (715 mm)
32 ” (816 mm)
24” 22 ” (574 mm)
Hole Pattern for Keyboard Drawer
” Diameter
” Deep
6 Holes
P.O. Box 725 • 421 Industrial Avenue • • Phone: [phone] • Fax: [phone] • [e-mail] • www.novadesk.com
FPA-0-1818 Asy. Instr. 09/23 Patents Pending Page 1
Desk Mount Extension Tube
1.26”
(32mm)
1.26”
(32mm)
A2
” Diameter
” Deep
6 Holes
This kit ships with a 100mm VESA plate. If all four of the 100mm VESA plate
holes do not line up with the holes on the back of monitor, you may require
a smaller (75mm) VESA plate, which is sold separately. Also available with a
Privacy/Glare Visor (sold separately). Contact Customer Service for more
information.
PACKING LIST
QTY REF # ITEM # DESCRIPTION
1 A1 100mm *VESA Plate
1 A2 FPA-8-2006 Desk Mount Extension Tube
1 A3 VESA Plate Extension Tube
1 B 014138 Wing Screw
10 C 1412APPBO Screw, #14 x 3/4”, PHP, Black
1 D 20060126 Keyboard Hanger w/ Glide - Left
1 E 20060127 Keyboard Hanger w/ Glide - Right
1 F Varies Keyboard Drawer
1 G 6737 Glass, 18”x 18”
2 H 0149085 Screw, #14 x 1-1/2”, PHP, Black
4 J 0141158 Screw, #6 x 5/8”, PHP, Black
4 K 50900034 Trim Ring Corner
4 L 50900035 Trim Ring Straight - 15”
4 N 91200 Screw, M4-0.7 x 8mm, PHP, Zinc
Includes:
Flat Panel Display Arm,
Keyboard Drawer, Glass,
and Trim Ring.
Also Available:
Privacy/Glare Visor
(Sold Separately)
*VESA 100 Standard

Step 6. Install trim ring & viewport glass
Step 3.
Figure 4
C
H
VESA Plate
Adjustment
D
E
H
C
Figure 5
Step 5
Step 4.
Attach Flat Panel Display to VESA plate
Figure 2
A1
A2
N
Figure 3
100 mm
(3-
15/16")
4-7/16"
100 mm
(3-
15/16")
320°
270°
Monitor Angle
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
B
A3
B
C
A1
Align holes in Desk Mount Extension Tube (A2) with holes in
worksurface (Figure 2) and attach using 6 screws (C). The Flat
Panel Display Arm comes fully assembled.
WARNING: Removing the set screws or oiling the joints
could cause the flat panel display to fall and void the
warranty.
Flat Panel Arm
ships fully
assembled.
Remove flat panel display base. Attach flat panel display to
VESA plate (using screws located on the back of your flat
panel display supplied by manufacturer). See Figure 3
Depress silver spring pin on VESA plate extension tube and
slide it into the desk mount extension tube. Tighten wing
nut (B, Figure 4). See “Monitor Angle” for adjustment
guidance. When installing some Apple® flat panel
displays, a VESA Adapter may be necessary. Contact
Customer Support for more information.
Attach
keyboard
hangers (D, E,
Figure 5) to
underside of worksurface
with screws (C, H).
IMPORTANT: The longer
screws (H) pass through the
tubular section of the
keyboard hanger. That
allows the assembly to be
leveled by loosening or
tightning the screws.
Snap trim ring pieces
(K, L) together. Insert
into viewport cutout
and attach with
screws (J). Carefully
insert viewport glass
(G) into trim ring.
Slide Keyboard
drawer into glides
and use locking tabs to
secure in place.
Locking Tab:
Locked when pushed towards user and
unlocked when pushed away.
1. Position screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen
should be closer to eyes than top of screen).
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and raise
flat panel display.
A2
A3
FPA-0-1818 Asy. Instr. 09/23 Patents Pending Page 2
L
K
Back edge of cut-out

FRONT EDGE
Dimension A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(32mm)
(Typ.)
Wide s c r e e n F o r m a t
Figure 1A
Step 1.
Step 2.
The natural way to look at a computer
Figure 1B
Assembly Instructions
Cut opening for viewport (Figure 1A). When ordering with a
keyboard, prepare surface for keyboard drawer (Figure 1B).
Using the hole pattern on the Desk Mount Extension Tube (A2)
as a template, locate and drill holes (Figure 1A). Please note drill
size and hole depth.
Flat Panel Display Arm
FPA-0-1821-NK-___
Keyboard Size
-XK for No
Keyboard
Option
Keyboard Size Options: 24 / 28 / 30 / 34
Desk Mount Extension Tube
1.26”
(32mm)
1.26”
(32mm)
A2
” Diameter
” Deep
6 Holes
FRONT EDGE
All corners
3"
(76 mm)
Center on
viewport opening
"
24”
(609.6 mm)
18 ¼”
(464 mm)
20 ”
(526 mm)
A2
UNDERSIDE OF TOP CLEARANCE
24” (609.6 mm) minimum clearance depth of worksurface
½” (12.7 mm) R.
Keyboard Drawer Size Dimension A
28”
30”
34”
26 ” (664 mm)
28 ” (715 mm)
32 ” (816 mm)
24” 22 ” (574 mm)
Hole Pattern for Keyboard Drawer
” Diameter
” Deep
6 Holes
P.O. Box 725 • 421 Industrial Avenue • • Phone: [phone] • Fax: [phone] • [e-mail] • www.novadesk.com
FPA-0-1821 Widescreen Asy. Instr. 09/23 Patents Pending Page 1
Includes:
Flat Panel Display Arm,
Keyboard Drawer, Glass,
and Trim Ring.
Also Available:
Privacy/Glare Visor
(Sold Separately)
This kit ships with a 100mm VESA plate. If all four of the 100mm VESA plate
holes do not line up with the holes on the back of monitor, you may require
a smaller (75mm) VESA plate, which is sold separately. Also available with a
Privacy/Glare Visor (sold separately). Contact Customer Service for more
information.
PACKING LIST
QTY REF # ITEM # DESCRIPTION
1 A1 100mm *VESA Plate
1 A2 FPA-8-2006 Desk Mount Extension Tube
1 A3 VESA Plate Extension Tube
1 B 014138 Wing Screw
10 C 1412APPBO Screw, #14 x 3/4”, PHP, Black
1 D 20060126 Keyboard Hanger w/ Glide - Left
1 E 20060127 Keyboard Hanger w/ Glide - Right
1 F Varies Keyboard Drawer
1 G 7467 Glass, 18”x 20.5”
2 H 0149085 Screw, #14 x 1-1/2”, PHP, Black
4 J 0141158 Screw, #6 x 5/8”, PHP, Black
4 K 50900034 Trim Ring Corner
2 L 50900035 Trim Ring Straight - 15“
2 M 50900036 Trim Ring Straight - 17.5“
4 N 91200 Screw, M4-0.7 x 8mm, PHP, Zinc
*VESA 100 Standard

Step 6. Install trim ring & viewport glass
Step 3.
Figure 4
C
H
VESA Plate
Adjustment
D
E
H
C
K
L
Figure 5
Step 5
Step 4. Attach Flat Panel Display to VESA plate
Figure 2
A1
A2
N
Back edge of cut-out
Figure 3
100 mm
(3-
15/16")
4-7/16"
100 mm
(3-
15/16")
320°
270°
Monitor Angle
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
B
A3
B
C
A1
Align holes in Desk Mount Extension Tube (A2) with holes in
worksurface (Figure 2) and attach using 6 screws (C). The Flat
Panel Display Arm comes fully assembled.
WARNING: Removing the set screws or oiling the joints
could cause the flat panel display to fall and void the
warranty.
Flat Panel Arm
ships fully
assembled.
Remove flat panel display base. Attach flat panel display to
VESA plate (using screws located on the back of your flat
panel display supplied by manufacturer). See Figure 3
Depress silver spring pin on VESA plate extension tube and
slide it into the desk mount extension tube. Tighten wing
nut (B, Figure 4). See “Monitor Angle” for adjustment
guidance. When installing some Apple® flat panel
displays, a VESA Adapter may be necessary. Contact
Customer Support for more information.
Attach
keyboard
hangers (D, E,
Figure 5) to
underside of worksurface
with screws (C, H).
IMPORTANT: The longer
screws (H) pass through the
tubular section of the
keyboard hanger. That
allows the assembly to be
leveled by loosening or
tightning the screws.
Snap trim ring pieces
(K, L, M) together.
Insert into viewport
cutout and attach with
screws (J). Carefully
insert viewport glass
(G) into trim ring.
Slide Keyboard
drawer into glides
and use locking tabs to
secure in place.
Locking Tab:
Locked when pushed towards user and
unlocked when pushed away.
1. Position screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen
should be closer to eyes than top of screen).
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and raise
flat panel display.
A2
A3
FPA-0-1821 Widescreen Asy. Instr. 09/23 Patents Pending Page 2
M

FRONT EDGE
Dimension A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(32mm)
(Typ.)
Figure 1A
Step 1.
Step 2.
The natural way to look at a computer
Figure 1B
Retrot Kit
Assembly Instructions
Cut opening for viewport (Figure 1A). When ordering with a
keyboard, prepare surface for keyboard drawer (Figure 1B).
Using the hole pattern on the Desk Mount Extension Tube (A2)
as a template, locate and drill holes (Figure 1A). Please note drill
size and hole depth.
Flat Panel Display Arm
FPA-0-2121-NK-___
Keyboard Size
-XK for No
Keyboard
Option
Keyboard Size Options: 24 / 28 / 30 / 34
Desk Mount Extension Tube
1.26”
(32mm)
1.26”
(32mm)
A2
⁄” Diameter
⁄” Deep
6 Holes
FRONT EDGE
All corners
3"
(76 mm)
Center on
viewport opening
¼"
27 ¼”
(692 mm)
21 ¼”
(540 mm)
21 ¼”
(540 mm)
A2
UNDERSIDE OF TOP CLEARANCE
27 ¼” (692mm) minimum clearance depth of worksurface
½” (12.7 mm) R.
Keyboard Drawer Size Dimension A
27”
28”
30”
34”
25 ⁄” (643 mm)
26 ⁄” (664 mm)
28 ⁄” (713 mm)
32 ⁄” (816 mm)
24” 22 ⁄” (574 mm)
Hole Pattern for Keyboard Drawer
⁄” Diameter
⁄” Deep
6 Holes
P.O. Box 725 • 421 Industrial Avenue • Effingham, IL 62401 • Phone: [phone] • Fax: [phone] • [email protected] • www.novadesk.com
Includes:
Flat Panel Display Arm,
Keyboard Drawer, Glass,
and Trim Ring.
Also Available:
Privacy/Glare Visor
(Sold Seperately)
This kit ships with a 100mm VESA plate. If all four of the 100mm VESA plate
holes do not line up with the holes on the back of monitor, you may require
a smaller (75mm) VESA plate, which is sold seperately. Also available with a
Privacy/Glare Visor (sold seperately). Contact Customer Service for more
information.
PACKING LIST
QTY REF # ITEM # DESCRIPTION
1 A1 100mm *VESA Plate
1 A2 FPA-8-2006 Desk Mount Extension Tube
1 A3 VESA Plate Extension Tube
1 B 014138 Wing Screw
10 C 1412APPBO Screw, #14 x 3/4”, PHP, Black
1 D 20060126 Keyboard Hanger w/ Glide - Left
1 E 20060127 Keyboard Hanger w/ Glide - Right
1 F Varies Keyboard Drawer
1 G 7436 Glass, 21”x 21”
2 H 0149085 Screw, #14 x 1-1/2”, PHP, Black
4 J 0141158 Screw, #6 x 5/8”, PHP, Black
4 K 50900034 Trim Ring Corner
4 L 50900037 Trim Ring Straight - 18”
4 M 91200 Screw, M4-0.7 x 8mm, PHP, Zinc
*VESA 100 Standard
FPA-0-2121 Asy. Instr. 09/23 Patents Pending Page 1

Step 6. Install trim ring & viewport glass
Step 3.
Figure 4
C
H
VESAPlate
Adjustment
D
E
H
C
Figure 5
Step 5
Step 4.
Attach Flat Panel Display to VESA plate
Figure 2
A1
A2
N
Figure 3
100 mm
(3-
15/16")
4-7/16"
100 mm
(3-
15/16")
320°
270°
Monitor Angle
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
B
A3
B
C
A1
Align holes in Desk Mount Extension Tube (A2) with holes in
worksurface (Figure 2) and attach using 6 screws (C). The Flat
Panel Display Arm comes fully assembled.
WARNING: Removing the set screws or oiling the joints
could cause the flat panel display to fall and void the
warranty.
Flat Panel Arm
ships fully
assembled.
Remove flat panel display base. Attach flat panel display to
VESA plate (using screws located on the back of your flat
panel display supplied by manufacturer). See Figure 3
Depress silver spring pin on VESA plate extension tube and
slide it into the desk mount extension tube. Tighten wing
nut (B, Figure 4). See “Monitor Angle” for adjustment
guidance. When installing some Apple® flat panel
displays, a VESA Adapter may be necessary. Contact
Customer Support for more information.
Attach
keyboard
hangers (D, E,
Figure 5) to
underside of worksurface
with screws (C, H).
IMPORTANT: The longer
screws (H) pass through the
tubular section of the
keyboard hanger. That
allows the assembly to be
leveled by loosening or
tightning the screws.
Snap trim ring pieces
(K, L) together. Insert
into viewport cutout
and attach with
screws (J). Carefully
insert viewport glass
(G) into trim ring.
Slide Keyboard
drawer into glides
and use locking tabs to
secure in place.
Locking Tab:
Locked when pushed towards user and
unlocked when pushed away.
1. Position screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen
should be closer to eyes than top of screen).
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and raise
flat panel display.
A2
A3
FPA-0-2121 Asy. Instr. 09/23 Patents Pending Page 2
L
K
Back edge of cut-out

FRONT EDGE
Dimension A
2
1
/ 2 "
(64 mm )
4
"
(102 mm )
1-1/4"
(32mm)
(Typ.)
Wide s c r e e n F o r m a t
Figure 1A
Step 1.
Step 2.
The natural way to look at a computer
Figure 1B
Assembly Instructions
Cut opening for viewport (Figure 1A). When ordering with a
keyboard, prepare surface for keyboard drawer (Figure 1B).
Using the hole pattern on the Desk Mount Extension Tube (A2)
as a template, locate and drill holes (Figure 1A). Please note drill
size and hole depth.
Flat Panel Display Arm
FPA-0-2124-NK-___
Keyboard Size
-XK for No
Keyboard
Option
Keyboard Size Options: 28 / 30 / 34
Desk Mount Extension Tube
1.26”
(32mm)
1.26”
(32mm)
A2
” Diameter
” Deep
6 Holes
FRONT EDGE
All corners
3"
(76 mm)
Center on
viewport opening
¼"
27 ¼”
(692 mm)
21 ¼”
(540 mm)
24 ¼”
(616 mm)
A2
UNDERSIDE OF TOP CLEARANCE
27 ¼” (692mm) minimum clearance depth of worksurface
½” (12.7 mm) R.
Keyboard Drawer Size Dimension A
28”
30”
34”
26 ” (664 mm)
28 ” (713 mm)
32 ” (816 mm)
Hole Pattern for Keyboard Drawer
” Diameter
” Deep
6 Holes
P.O. Box 725 • 421 Industrial Avenue • • Phone: [phone] • Fax: [phone] • [e-mail] • www.novadesk.com
FPA-0-2124 Widescreen Asy. Instr. 09/23 Patents Pending Page 1
Includes:
Flat Panel Display Arm,
Keyboard Drawer, Glass,
and Trim Ring.
Also Available:
Privacy/Glare Visor
(Sold Separately)
This kit ships with a 100mm VESA plate. If all four of the 100mm VESA plate
holes do not line up with the holes on the back of monitor, you may require
a smaller (75mm) VESA plate, which is sold separately. Also available with a
Privacy/Glare Visor (sold separately). Contact Customer Service for more
information.
PACKING LIST
QTY REF # ITEM # DESCRIPTION
1 A1 100mm *VESA Plate
1 A2 FPA-8-2006 Desk Mount Extension Tube
1 A3 VESA Plate Extension Tube
1 B 014138 Wing Screw
10 C 1412APPBO Screw, #14 x 3/4”, PHP, Black
1 D 20060126 Keyboard Hanger w/ Glide - Left
1 E 20060127 Keyboard Hanger w/ Glide - Right
1 F Varies Keyboard Drawer
1 G 2124 Glass, 21“ x 24”
2 H 0149085 Screw, #14 x 1-1/2”, PHP, Black
4 J 0141158 Screw, #6 x 5/8”, PHP, Black
4 K 50900034 Trim Ring Corner
2 L 50900037 Trim Ring Straight - 18“
2 M 50900038 Trim Ring Straight - 21“
4 N 91200 Screw, M4-0.7 x 8mm, PHP, Zinc
*VESA 100 Standard

Step 6. Install trim ring & viewport glass
Step 3.
Figure 4
C
H
VESA Plate
Adjustment
D
E
H
C
K
L
Figure 5
Step 5
Step 4. Attach Flat Panel Display to VESA plate
Figure 2
A1
A2
N
Back edge of cut-out
Figure 3
100 mm
(3-
15/16")
4-7/16"
100 mm
(3-
15/16")
320°
270°
Monitor Angle
viewport cut-out
Silver spring pin
Desk mount
Extension tube VESA plate
Extension tube
B
A3
B
C
A1
Align holes in Desk Mount Extension Tube (A2) with holes in
worksurface (Figure 2) and attach using 6 screws (C). The Flat
Panel Display Arm comes fully assembled.
WARNING: Removing the set screws or oiling the joints
could cause the flat panel display to fall and void the
warranty.
Flat Panel Arm
ships fully
assembled.
Remove flat panel display base. Attach flat panel display to
VESA plate (using screws located on the back of your flat
panel display supplied by manufacturer). See Figure 3
Depress silver spring pin on VESA plate extension tube and
slide it into the desk mount extension tube. Tighten wing
nut (B, Figure 4). See “Monitor Angle” for adjustment
guidance. When installing some Apple® flat panel
displays, a VESA Adapter may be necessary. Contact
Customer Support for more information.
Attach
keyboard
hangers (D, E,
Figure 5) to
underside of worksurface
with screws (C, H).
IMPORTANT: The longer
screws (H) pass through the
tubular section of the
keyboard hanger. That
allows the assembly to be
leveled by loosening or
tightning the screws.
Snap trim ring pieces
(K, L, M) together.
Insert into viewport
cutout and attach with
screws (J). Carefully
insert viewport glass
(G) into trim ring.
Slide Keyboard
drawer into glides
and use locking tabs to
secure in place.
Locking Tab:
Locked when pushed towards user and
unlocked when pushed away.
1. Position screen as high as possible without raising glass.
2. Aim screen slightly above user’s eyes. (Bottom of screen
should be closer to eyes than top of screen).
3. Preferred location is with top edge of flat panel display at back
edge of glass.
4. For semi-recessed positions, remove viewport glass and raise
flat panel display.
A2
A3
FPA-0-2124 Widescreen Asy. Instr. 09/23 Patents Pending Page 2
M