Nova Solutions Trolley Manual

b.
s
Phillips Screwdriver
Power screwdriver may also be used.
Parts List
The Trolley™
Monitor lift System
Installation & Operating Instructions
Step 1:
The Trolley™ Removable Metal
Front Cover
100mm VESA
Plate
Qty. 1
Pan head #10 x 5/8
Black Screw for
front cover
Qty. 4
8-32 x 7/8
Locking Plate Screw,
Longer
Qty. 4
Locking Plates
Qty. 4
10-24 x 3/4
Locking Plate Screw,
Shorter
Qty. 1
4mm x 0.7
Anti-tilt screw, black
(Pre-installed in
Tounge of VESA Plate
Note: Do not connect the Trolley™ to power source until step 4
1a. Remove Trolley™ and parts from shipping box.
1b. Place Trolley™ in it’s upright, vertical position
with the open interior side facing you.
Step 2:
a.
Tools (not included)
Need assistance? Call 1-800-730-6682 for NOVA Solutions Customer Support
2a. With arm in down
position, remove
black cable
management
cover.
2b. Remove right
screw from cable
retention clip on
cable management
channel. Then
loosen left screw
and rotate clip
downward.

Step 3:
Step 4:
4b. With the open side of the Trolley™
facing the user side of the desk, place
Trolley™ on work surface adjacent to
work surface cutout.
Feed video and power cables through
cutout.
4a. Position locking plates as shown, over
four threaded hole locations in Trolley™.
Use (4) shorter 10-24 x 3/4 locking
plate screws and tighten locking plates.
Insert (4) longer locking plate screws into
second locking plate hole. Finish
tightening in Step 4e.
Video Port Power Port
Flat panel monitor (bottom view). Dell monitor pictured here. Other brands may vary.
B
Side Grommet
Side Grommet
C
D
E
A. Feed monitor video and power cables through the grommets
on either side of the Trolley™.
B. Align other end of video & power cables with ports on monitor.
Position the end of the cables even with the center of the VESA
plate on monitor arm. These cords may need adjustment in step
6b.
C. Leave about 1” of clearance between the video/power cables
and the bottom of the Trolley™.
D. Place video/power cables in two center wire management
channels on monitor arm. Bring wire clip (rotated downward
in step 2b) back up over wires, aligning right side over screw
hole. Tighten left screw, then reinstall and tighten right screw.
E. Place video and power cables in wire retention clamps on side
grommet. Secure screws in grommet. Make sure all wires are
clear of screw hole. See figures 1 & 2.
F. Reinstall black cable management cover that was removed in
step 2.
G. Completely remove two shipping screws indicated by the
yellow warning label.
Fig. 1 - Side grommet
with wire retention
clamps
F
b.
a.
4c. Lower Trolley™ into the cutout.
c.
4f. Plug the Trolley™ into power source. Wait 5 seconds to
activate, then push the UP button to open door and
raise the Trolley™ arm.
4d. Turn locking tabs 90°.
4e. Tighten locking plate
screws to worksurface
tight enough to
prevent the Trolley™
from shifting.
1”
Fig. 2 - Top view
of wire retention
clamps
d.
e.
WARNING: After screws are removed and
before monitor is installed, arm may move
upward. If this happens, it should be
stopped by holding it with your hand.
A
A
Need assistance? Call 1-800-730-6682 for NOVA Solutions Customer Support
Page 2 of 4
The Trolley™
Monitor lift System
Installation & Operating Instructions

b.
6b.
Step 5:
Step 6:
5a. Confirm appropriate size VESA
plate for your monitor.
(100mm VESA plate installed)
Note: Once installed, the bottom of your
monitor should be 1 1/2” to 2” above the
closed Trolley™ door.
c.
Step 7:
c.
.
b.
a.
(H)
a.
a.
5b. VESA plates
can be detached
and rotated to
ensure a monitor
height clearance
of 1 1/2” to 2”
above the closed
Trolley™ door.
5c. Depending on the depth of your monitor’s VESA plate mounting area and/or the
thickness of your monitor, different screw holes can be used to adjust the space
between the monitor and the Trolley™ arm.
Using the
flush screw
holes
increases
the space
between
the monitor
and the
arm.
c. Using the
indented
screw holes
decreases
the space
between
the monitor
and the
arm.
(G)
Note: To enable the
adjustability of the
monitor, remove the
Anit-tilt Screw (G) witch
secures the VESA plate to
arm.
Optional: If 75mm VESA
plate is required, contact
Customer Service at
1-800-730-6682
6a. Remove the four
screws located
on back of
monitor.
6b. Attach the video and power cables to
your monitor. Allow enough slack in
cables for easy tilting of monitor, but
do not allow them to touch the work
surface or interfere with Trolley
operation
Note: cables should
allow for monitor tilt,
but should not touch
work surface
6c. Attach monitor to
VESA plate using
the four removed
monitor screws.
Note: It may be helpful to
have another person assist in
holding the monitor while
attaching it to the VESA
plate.
7a. Push “Down” button for a
few seconds to activate
unit. Once the monitor is
completely lowered into
the Trolley™, the door will
close automatically.
Note: Pushing the “Up” button
will close the door.
7b. Remove the black screw located
at the bottom of the Trolley™
(H). Slide the top end of the
removable metal front cover
into the upper front cover slot.
Note: Top of front cover must slide
inside the groove of the top structure.
Slide bottom of cover into
Trolley™ aligning with screw
hole. Reinstall the screw.
b.
Need assistance? Call 1-800-730-6682 for NOVA Solutions Customer Support
Page 3 of 4
(H) Pan head #10 x 5/8 Black Screw for front cover
The Trolley™
Monitor lift System
Installation & Operating Instructions

Overview
The Trolley™ EXL includes Intelligent Motion Technology™. This feature reduces the risk of accidental
damage and personal injury. Utilizing information from various different sensors, Intelligent Motion
Technology™ continually monitors the Trolley’s™ opperational status and delivers information to the
power control module.
If conditions create a “conflict” within the Trolley’s™ programming, the system will automatically take
action to reduce damage or injury. See below for some common operational conditions and how to
resume normal operation.
Operational Guidelines / Troubleshooting
Condition Opperational
Status To Resume Opperation...
Power Failure
• In the event of a power failure during operation... Unit will STOP Once power is restored, push the “Up” button to
resume normal operation. The Trolley™ will return to
the “Up” postion.
Obstruction During Upward Motion
• If someone or something obstructs the upward
motion of the monitor (such as someone leaning
on or pushing down on the monitor)...
Unit will STOP Once obstruction is cleared, push the “Up” button to
resume normal operation. The Trolley™ will return to
the “Up” postion.
Monitor is Tilted During Operation
• If the monitor is moved out of vertical alignment
while Trolley™ is operating...
Unit will STOP Move monitor to fully vertical position. Push “Up” to
resume normal operation.
Note: The Trolley™ will not operate when the monitor
is tilted
Access Door is Obstructed or Jammed
• If the Trolley™ senses an obstruction in the path
of the access door...
Unit will STOP The Trolley’s™ “Over-current Sensor” will stop the unit
from operating until the door obstruction is removed.
Once the path is clear, push either “Up” or “Down”
buttons to resume normal operation.
For more information on installation and operation of the Trolley™ EXL,
please contact NOVA at 800-730-6682 or [email protected]
Need assistance? Call 1-800-730-6682 for NOVA Solutions Customer Support
Page 4 of 4
Trolley_Retro_Inst_05/19
The Trolley™
Monitor lift System
Installation & Operating Instructions