Novoterm Kerra Tuluza User manual

Thank you for purchasing our product. Please
read this manual carefully before cabin
installation.
Pictures in this manual are for
information purposes only.
Due to product specificity we recommend installation
of the cabin by authorized installation service. Current
list of authorized service points is available on our
website www.novoterm.pl or at:
801 144 200
NOTE: If you decide to install the cabin yourself, we would like to advise that due to safety reasons
plumbing and electrical installation of the device must be performed by a qualified plumber or licensed
electrician. Those systems must be executed in compliance with applicable laws and regulations. Incorrect
installation may cause cabin damage!
BEFORE INSTALLATION MAKE SURE THAT:
1. 1. The place where the cabin is to be installed
has been prepared as shown on the drawing
(fig. 1).
2. Water connection is ½’’ and together with the
valves does not stick away from the wall further
than 30 mm.
3. The prepared drain hole is 50mm in diameter and
is adapted to standard rubber reducers available
on the market. The set does not include a reducer.
4. The hot water temperature is not higher than
65°C. Higher water temperature may causa
faster wear of plumbing elements of the cabin.
5. The plumbing system has been flushed and
equipped with angle valves with mechanical
water filters.
6. Static pressure in the water supply system does
not exceed 4.5 bar. For safety reasons
we recommend installation of pressure reducer
regardless of the measurement results –
temporary pressure fluctuations are possible
even if it is not shown by a measurement.
7. We recommend connecting the cabin to the
municipal water mains, a water storage
heater or heater with electronic temperature
control. Do not connect the cabin to a
hydraulic instantaneous water heater.
For some functions such heater may not turn
on or water may not reach the temperature
desired.
8. Electricity connection or electrical socket are
placed at the height preventing water access or
ensuring that it is resistant to water ingress. The
terminal box or socket must be at least IP45
water resistant. Cabins equipped with grounding
cable must be permanently connected to the
electrical system. Electrical system must be
compliant with PN-EN-60335-1 standard.
9. The supply system is equipped with a 30 mA
residual current circuit breaker with contact
spacing minimum 3 mm.
10. The supply voltage is compliant with the
parameters set out on the rating plate and
protection is minimum 1A.
11. The room where the cabin is to be installed is
equipped with working and efficient ventilation
system.
12. The place of cabin installation has level surface
at even level with the remaining part of the room,
and level vertical walls.
Compliance with the above requirements is necessary for correct installation and use of the cabin
tuluza 2.indd 2
2014-09-02 08:36:21
INSTALLATION
MANUAL
HYDROMASSAGE CABIN
TULUZA

Recommended hydraulic pressure: 2-4 bar
Recommended hot water temperature: 55 - 65°C
Recommended cold water temperature: 10 - 20°C
Cabin size: 120.5 x 80.5 x 217 cm
TECHNICAL PARAMETERS
- space for the cabin
- space that must remain free after the cabin installation
electrical
connection
water
connection
water drain
Fig. 1

To make sure that cabin installation runs smoothly, please get the following tools ready:
To install the cabin you will need hoses supplying cold and hot water from the water system to the cabin (not provided in the set).
Hose parameters should be as follows: ½’’ x ½’’, length of supply hoses should be selected according to individual needs.
LIST OF COMPONENTS:
NOTE: Check if the set is complete immediately after purchase. Any missing or damaged parts should be immediately
reported to the seller
TOOLS REQUIRED

symbol
name
qty
symb
ol
name
qty
A
small head screw 4 x 25
8
5
shower panel
1
B
large head screw 4 x 14
10
6
right rear wall
1
C
large head screw 4 x 12
32
7
right rear wall
1
D
large head screw 4 x 35
2
8
right corner profile
1
E
sleeve f 6 x 5,5
2
9
shower tray
1
F
stopper
2
10
top horizontal profile
1
G
jet ended with stopper
1
11
left side profile
1
H
jet
5
12
“ U ” s h ap e cr o s s-section seal
2
I
door handle
2
13
fixed front glass
1
J
shower set
1
14
door side seal
2
K
shelf
1
15
door glass
1
L
power supply
1
16
magnetic seal
2
M
hinge
4
17
right door glass
1
N
drainage
1
18
fixed front glass
1
O
band clip
12
19
right side profile
1
P
connecting hose - 250 cm
1
20
bottom seal of front glass
2
left corner profile
1
21
bottom door seal
2
2
left rear wall
1
22
short horizontal profile
2
3
left rear wall
1
23
bottom horizontal profile
1
4
top cover
1
tuluza 2.indd 6
2014-09-02 08:36:23

Glass elements of the cabin are made of safety glass.
It is necessary to be particularly careful during
unpacking, handling and installation of glass parts.
The glass should not be put directly on the floor or
leaned against walls. Do not hit them or lever with
hard tools. Damaged glass will break into tiny pieces!
Before finishing with silicone clean all surfaces of any dirt.
We recommend to wait about 24 hours after the cabin
installation for the silicone to bind.
Openings for the drainage in the shower tray are
standard size. If necessary, you may use different
drainage set than the one provided in the set.
NOTE: Check all components before installation. Do
not install the cabin if you find that any of the
components is damaged! After the cabin is installed,
no complaints on this account will be accepted!
u
s
z
c
z
e
l
n
i
c
t
a
s
m
a
t
e
f
l
o
n
o
w
a
L
e
a
v
e
a
g
a
p
o
f
m
i
n
i
m
u
m
2
m
m
b
e
t
w
e
e
n
t
h
e
f
l
o
o
r

X X
N> -»■

tuluza 2.indd 9
2014-09-02 08:36:24

tuluza 2.indd 10
2014-09-02 08:36:24

EH

EH

Cables are marked with labels. Connect to each other only those cables which are marked with the same
label.
Connecting hoses and drainage reducer are not provided in the
set.

Before finishing with silicone clean all surfaces!
Do not seal drainage holes in the upper part of the tray!!
After the cabin is finished with silicone we recommend waiting 24 hours for the adhesive to bind!
After the silicone binds, check if the cabin is waterproof! Any leaks should be removed before it is positioned by the wall!
Connect the cabin to the electrical system only after you have checked if it is waterproof!
It must be connected by a licensed electrician.
It must be connected in compliance with currently binding standards. At this stage, the telephone line should be connected if
you are going to use the telephone function.