Novus NVIP-2DN3031V/IR-1P-II User manual

User’s manual
(short )
NVIP-2DN3031V/IR-1P-II

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2014/30/UE) and LVD (2014/35/UE) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and
national regulations implementing the directives:
Electromagnetic compatibility EMC 2014/30/UE.
Low voltage LVD 2014/35/U.The Directive applies to electrical equipment designed for use with a
voltage rating of between 50VAC and 1000VAC as well as 75VDC and 1500VDC.
WEEE Directive 2012/19/EU
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and
Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is
disposed of correctly, you will help to prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance
may not be treated as household waste. It shall be handed over to the applicable collection point for
used up electrical and electronic equipment for recycling purpose. For more information about
recycling of this product, please contact your local authorities, your household waste disposal service
or the shop where you purchased the product.
RoHS Directive 2011/65/EU
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our
products have been tested and do not contain hazardous substances whose exceeding limits
could have negative impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other
devices during device operation.
WARNING!
Prior to undertaking any action that is not described for the given product in user’s manual and other
documents delivered with the product, or if it does not arise from the usual application of
the product, manufacturer must be contacted under the rigor of excluding the
manufacturer’s responsibility for the results of such an action.

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary.
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual.
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden.
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,
bath tubs, damp basements).
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself as a
consequence.
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to
supply the camera from a power sources with unknown parameters, unstable or not meeting
producer’s requirements.
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS .................................................................................................... 4
1. FOREWORD INFORMATION................................................................................... ..5
1.1. General characteristics......................................................................................... 5
1.2. Technical specification .................................................................................... ...6
1.3. Camera dimension ........................................................................................... ...7
1.4. Package contents .............................................................................................. ...7
2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8
2.1. View of the camera, layout of the camera items ................................................. 8
2.2. Connecting Ethernet cable................................................................................... 9
2.3. Connecting power supply to the camera .......................................................... 10
2.4. Installation ......................................................................................................... 10
2.5. Starting the camera............................................................................................ 11
2.6. Initial configuration via the web browser……………………………………..12
3. NETWORK CONNECTION USING WEB BROSWER ......................................... 13
3.1. Recommended PC specification for web browser ............................................. 13
3.2. Connection with IP camera via web browser..................................................... 13
4. WEB BROWSER INTERFACE ................................................................................. 15
4.1. Displaying live pictures...................................................................................... 15
5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 16
5.1. Connecting audio input ..................................................................................... 16
5.1. Connecting BNC analog video output .............................................................. 16
5.2. Memory card slot and RESET button………………………………………….16
6. RESTORING FACTORY DEFAULTS .................................................................... 17
6.1. Restoring factory defaults by software (web browser) ...................................... 17
6.2. Restoring factory defaults by software (IPtool) ................................................ 17
6.3. Restoring factory defaults by hardware using RESET button .......................... 17
TABLE OF CONTENTS

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
 Imager resolution: 2.0 megapixels
 Mechanical IR cut filter, IR operation capability
 Min. Illumination from 0 lx with IR LED on
 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions
 Digital Noise Reduction (DNR)
 Lens type: standard, f= 2.8mm/F=1.85
 Built-in LED illuminator: 16 pcs LED
 Built-in webserver: compresses and transmits over a network of video and audio in real time
 Compression: H.264, H.265/ MJPEG
 Max video processing resolution: 1920 x1080
 Multi streaming (3 video streams)
 Compression, resolution, speed and quality defined individually for each video stream
 ROI functions
 Private Zones
 Motion detection
 RTP/RTSP protocol support for video transmission
 Schedule functions
 Post-alarm functions
 Audio input
 BNC output
 Built-in webserver: camera configuration through the website
 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server, SD
card
 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
 Video Content Analysis (VCA):
Exception
Line Crossing
Intrusion
 Power supply: 12VDC, PoE (Power over Ethernet)
FOREWORD INFORMATION

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
6
1.2. Technical specification
FOREWORD INFORMATION
IMAGE
Image Sensor 2 MPX CMOS sensor 1/2.7” APTINA
Number of Eecve Pixels 1920 (H) x 1080 (V)
Min. Illuminaon 0.12 lx/F1.85 - color mode,
0 lx (IR on) - B/W mode
Electronic Shuer auto: 1/25 s ~ 1/100000 s
Wide Dynamic Range (WDR) yes
Digital Noise Reducon (DNR) 3D
Defog Funcon (F-DNR) yes
LENS
Lens Type standard, f=2.8 mm/F1.85
DAY/NIGHT
Switching Type mechanical IR cut lter
Switching Mode auto, manual, me
Switching Level Adjustment yes
Switching Schedule yes
Visible Light Sensor yes
NETWORK
Stream Resoluon 1920 x 1080 (Full HD), 1280 x 720 (HD), 720 x 576 (D1), 480 x 270, 352 x 288 (CIF)
Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resoluons
Mulstreaming Mode 3 streams
Video/Audio Compression H.264, H.265, MJPEG/G.711
Number of Simultaneous Connecons max. 4
Bandwidth 8 Mb/s in total
Network Protocols Support TCP/IP, UDP, FTP, DHCP, DDNS, NTP, RTSP, UPnP, PPPoE, SMTP
ONVIF Protocol Support Prole S (ONVIF 2.3)
Camera Conguraon from Internet Explorer, languages: Polish, English, Russian, and others
Compable Soware NMS
OTHER FUNCTIONS
Privacy Zones 4
Moon Detecon yes
Region of interest (ROI) 8
Image Processing 90˚ image rotaon, 180˚ image rotaon, 270˚ image rotaon, ip, sharpening, mirror eect
Prealarm/Postalarm -/up to 120 s
System Reacon to Alarm Events e-mail with aachment, saving le on FTP server, saving le on SD card
IR LED
LED Number 16
Range 20 m
Angle 90°
INTERFACES
Video Output BNC, 1.0 Vp-p, 75 Ohm
Audio Input/Output 1 x Jack (3.5 mm)/-
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Memory card slot microSD up to 128GB
INSTALLATION PARAMETERS
Dimensions (mm) 117 (Ф) x 90 (H)
Weight 0.62 kg
Degree of Protecon IP 66 (details in the further part of this manual on page 10)
Enclosure vandal proof IK10, aluminium, white
Power Supply PoE, 12 VDC
Power Consumpon 3 W, 6 W (IR on)
Operang Temperature -20°C ~ 50°C

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
7
FOREWORD INFORMATION
1.3. Camera dimensions
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 Accessories bag
 Short version of user’s manual
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches
the temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
8
START-UP AND INITIAL IP CAMERA CONFIGURATION
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
2.1. View of the camera, layout of the camera items
1. BNC output
2. Audio input
3. Power supply 12VDC
4. 100 Mb/s Ethernet port (RJ-45 hermetic connector)
5. Cover screws
6. IR Illuminator
7. Day/night sensor
5
6
7

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
9
2.2. Connecting ethernet cable
To maintain tightness of ethernet cable connection, please follow instruction below:
1. Loosen the nut (a) from the main element (b).
2. Put network cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45
connector.
3. Connect the cable to the hermetic connector (c), screw main cover (b), then screw the nut (a).
Warning! Other connectors and sockets ar e not her metically sealed. User should ensur e their
tightness on their own.
2.3. Connecting power supply to the camera.
Camera can be supplied using external power supply unit corresponding with the camera parameters or
by using RJ45 network socket and PoE (802.3at Type 1 ) power supply unit.
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
Caution:
It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not
compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that
results from the usage of improper power supply source are not covered by the warranty
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
START-UP AND INITIAL IP CAMERA CONFIGURATION
ab
a
b
c
12 VDC +
GND
Camera 12 VDC power supply connection schema

NVIP-2DN3031V/IR-1P-II - User’s manual (short) ver 1.0
All rights reserved © AAT Holding S.A.
10
2.4. Installation
1. Remove locking screw from camera base and then remove camera base.
2. Put base of the camera to the desired mounting surface, and mark drilling holes using base as a
template.
3. Drill mounting and cable holes in previously selected points.
4. Mount the camera base using included screws on smooth surface providing declared degree of IP
protection.
5. Adjust the position of the camera module. If required, loosen the screws blocking camera
module.
6. Put on the camera cover again, matching screws to the corresponding holes located in the base
of the camera and screwing until slight resistance is felt.
CAUTION!!!
The declared degree of protection of the camera relates to its housing and does not take into ac-
count the possibility of moisture infiltration into the interior of the camera by connecting cables.
Connection cables protection through i.e. sealing up is the responsibility of the camera installer.
The manufacturer is not liable for any damages to the camera caused as a result of failing in
performing that activity by installer, which also means that camera damaged in that way is not
subject to warranty repairs
START-UP AND INITIAL CAMERA CONFIGURATION