Novus NVIP-2DN5002V/IRH-1P User manual

U s e r ’s m a n u a l
( s h o rt f o r m)
NVIP-2DN5002V/IRH-1P

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
 Electromagnetic compatibility EMC 2004/108/EC.
 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2012/19/EU
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European Directive on Waste Electrical and Electronic
Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly,
you will help to prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2011/65/EU
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions described in the
manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com
website in order to access the newest manual
Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A. holds
exclusive rights to modify this manual. The producer reserves the rights for device specification modification
and change in the design without prior notice.

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS.....................................................................................................4
1. FOREWORD INFORMATION .....................................................................................5
1.1. General Characteristics........................................................................................5
1.2. NVIP-2DN5002V/IRH-1P tech specification ....................................................6
1.3. Camera dimension ..............................................................................................7
1.4. Package contents..................................................................................................8
2. START-UP AND INITIAL IP CAMERA CONFIGURATION .................................9
2.1. Description of connectors and control tools ........................................................9
2.2. Cable connectors................................................................................................10
2.3. NVIP-2DN5002V/IRH-1P mounting ................................................................10
2.4. Starting the IP camera........................................................................................11
2.5. Initial configuration via the Web browser.........................................................12
3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................15
3.1. Recommended PC specification for web browser .............................................15
3.2. Connection with IP camera via the Internet Explorer ........................................15
4. WWW INTERFACE - WORKING WITH IP CAMERA.........................................17
4.1. Displaying live pictures......................................................................................17
5. ELECTRIC CONNECTORS AND ACCESORIES .................................................19
5.1. Connecting power supply to the camera. ..........................................................19
5.2. Connecting alarm inputs and outpust .................................................................19
5.3. SD card installation ...........................................................................................19
6. RESTORING FACTORY DEFAULTS .....................................................................20
6.1. Restoring software factory defaults....................................................................20
6.2. Restoring hardware factory defaults in IP cameras............................................20
TABLE OF CONTENTS

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
 Imager resolution: 2 megapixels
 Mechanical IR cut filter
 IR operation capability
 Min. Illumination from 0,04 lx/F=2.3 , 0 lx (IR on)
 Digital Slow Shutter (DSS)
 Digital Noise Reduction (DNR)
 Wide Dynamic Range (WDR)
 Lens f=2.8m/F=2.3
 Built-in IR LED - 1 pcs., up to 6 m
 Privacy zones: 5
 Compression: H.264, M-JPEG
 Max video processing resolution : 1920x1080
 Dual stream mode compression, resolution, speed and quality defined individually for two video
streams
 RTP/RTSP protocol support for video transmission
 Pre & post-alarm functions
 Hardware motion detection
 Built-in webserver: camera configuration through the website
 MicroSD/SDHC card support
 Wide range of responses to alarm events: e-mail with attachment, saving file on microSD card,
 Network protocol support : ONVIF(2.2) ,HTTP, TCP/IP, IPv4/v6, UDP/IP, RTSP, FTP, DHCP,
NTP, PPPoE, SMTP
 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
 Power supply: VDC, PoE (Power over Ethernet)
FOREWORD INFORMATION

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
6
1.2. NVIP-2DN5002V/IRH-1P specification
FOREWORD INFORMATION
NVIP-2DN5002V/IRH-1P
IMAGE
Image Sensor 2 MPX CMOS sensor 1/2.8” APTINA
Number of Effective Pixels 1920 (H) x 1080 (V)
Min. Illumination 0.8 lx/F2.3 - color mode,
0.04 lx/F2.3 - color mode (DSS),
0 lx (IR on) - B/W mode
Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s
Digital Slow Shutter (DSS) up to 1/5 s
Wide Dynamic Range (WDR) yes
Digital Noise Reduction (DNR) 2D, 3D
LENS
Lens Type standard, f=2.8 mm/F2.3
Angle of View (H) 75°
DAY/NIGHT
Switching Type mechanical IR cut filter
Switching Mode auto, manual, time
Visible Light Sensor yes
NETWORK
Stream Resolution 1920 x 1080 (Full HD), 1280 x 720 (HD), 720 x 576 (D1), 640 x 480 (VGA),
640 x 360, 352 x 288 (CIF), 320 x 240 (QVGA), 176 x 144 (QCIF)
Frame Rate 30 fps for each resolution
Multistreaming Mode 2 streams
Video/Audio Compression H.264, MJPEG/G.711, RAW_PCM
Number of Simultaneous Connections max. 2
Bandwidth 5 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4, IPv4/v6, HTTPS, FTP, DHCP, DNS, 3GPP, SMTP
ONVIF Protocol Support Profile S (ONVIF2.2)
Camera Configuration from Internet Explorer, Firefox, Chrome, Opera browser languages: Polish,
English, Russian
Compatible Software NMS
OTHER FUNCTIONS
Privacy Zones 4
Motion Detection yes
Image Processing 90˚ image rotation, 180˚ image rotation, mirror effect
Prealarm/Postalarm up to 5 MB/up to 86400 s
System Reaction to Alarm Events e-mail with attachment, saving file on SD card
IR LED
LED Number 1
Range 6 m
Angle 90°
INTERFACES
Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only
Audio Input/Output 1 x RCA/1 x RCA
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Memory Card Slot microSD
INSTALLATION PARAMETERS
Dimensions (mm) 100 (Ф) x 53 (H)
Weight 0.32 kg
Enclosure vandal proof IK10 impact rating aluminium, white
Power Supply PoE, 12 VDC
Power Consumption 5 W, 7 W (IR on), 8.5 W (IR and heater on)
Operating Temperature -20°C ~ 55°C
Built-in Heater/Fan yes/no
Degree of Protection IP 65

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
7
FOREWORD INFORMATION
1.3. Camera dimensions
100 mm
30.3 mm
53 mm
100 mm
49.2 mm

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
8
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 230 VAC / 12 VDC power supply
 Accessories bag
 Short version of user’s manual
 CD containing manual and software
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 Accessories bag
 RJ45 Coupler
 BNC Test Cable
 Mounting Template
 Short version of user’s manual
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
FOREWORD INFORMATION

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
9
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
2.1. Camera interior overview
2.2. Cabel connectors
Note :
Use the included RJ45 coupler to connect to male end of RJ45 Ethernet cable.
START-UP AND INITIAL CAMERA CONFIGURATION
No. Color Description
1 - RJ-45 male network connector
2 White RCA Audio input
3 Red RCA Audio output
4 - 12V DC Power In

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
10
2.3. NVIP-2DN5002V/IRH-1P mounting
1.Use the included allen key to remove the camera cover screws (2x). Lift the cover away from the
camera
2. Use the included mounting template or the camera to mark holes for the mounting screws and cable.
3. Mount the camera to the surface using the included mounting screws (2x)
START-UP AND INITIAL CAMERA CONFIGURATION
Mounting Screw Hole
Termination cables
Mounting Screws

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
11
4. To adjust the viewing angle power up the camera. Connect to the camera using a web browser
(see the chapter 2.4 for details ) or you can insert the included BNC test cable into video test cable
terminals and connect to a test monitor .
Caution : Make sure to follow the correct polarity if connecting the camera to DC power. Polarity is
marked on the power connector.
Note :Use the included RJ45 coupler to connect to male end of RJ45 Ethernet cable.
Loosen the screws on the sides of the and adjust the ball camera. Do not remove the screws holding the
ball camera. Tighten the screws when finished.
Note : Ensure the ball camera is pointed in the same direction as the IR LED to ensure a good night
time image.
START-UP AND INITIAL CAMERA CONFIGURATION
Video test cable
Loosen screws to adjust the angle
of the camera ball
IR LED

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
12
5. (Optional) Insert a microSD card (not in set included ) into the camera. To enable recording, you
must format the microSD card and configure microSD recording.
Note : The camera supports microSD cards up to a maximum size of 32GB. SanDisk™ or Kingston™
brand microSD cards are recommended.
6. Ensure the rubber gasket inside the camera is properly in place, then replace the camera cover and
the camera cover screws (2x).
START-UP AND INITIAL CAMERA CONFIGURATION
microSD card

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
13
2.4. Starting the IP camera
To run NOVUS IP camera you have to connect ethernet cable between camera and network switch
with PoE support (IEEE 802.3af).
You can also connect it directly via power supply adapter with parameters compatible with camera
power supply specification.
After connecting power status red LED should light on. Initialization process is then started which can
take about 2 minutes. You can then proceed to connect to the camera via web browser.
If the connection is successfully established green network status LED blinks with a frequency
proportional to the quantity of data sent.
The recommended way to start an IP camera and perform its configuration is a connection directly
to the network switch which is not connected to other devices. To obtain further information about
network configuration parameters (IP address, gateway, network mask, etc.) please contact your
network administrator.
Note : Use the included RJ45 coupler to connect to male end of RJ45 Ethernet cable.
 Connection utilising network switch with PoE support
 Connection utilising external power supply and network switch
START-UP AND INITIAL CAMERA CONFIGURATION
Power supply and
network transmission
Computer
IP Camera
Network Switch
PoE
Network transmission
IP Camera
Network transmission
Network Switch Computer
Network transmission

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
14
 Connection utilising external power supply directly to the computer
Note :
Power supply adapter is not included. Please use power adapter with parameters specified in user‘s
manual.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
2.5. Initial configuration via the web browser
The default network settings for NVIP-1DN5xxx IP camera series are :
1. IP address= 192.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 192.168.1.1
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can
operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera
yourself or select DHCP mode (DHCP server is required in this method in target network) by using
web browser or by NMS software. When you use DHCP server check IP address lease and its linking
with camera MAC address to avoid changing or losing IP address during device operation or network/
DHCP server breakdown. You have to remember to use a new camera IP address after changing
network parameters.
After network setting configuration has been done, the camera can be connected to a target network.
START-UP AND INITIAL CAMERA CONFIGURATION
Network transmission - cross over cable
IP Camera Computer

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
15
3. NETWORK CONNECTION UTILIZING WEB BROSWER
3.1. Recommended PC specification for web browser connections
Requirements below apply to connection with an IP camera, assuming image display in 1280x960
resolution and 25 fps speed.
1. CPU Intel Pentium IV 3 GHz or newer
2. RAM Memory min. 512 MB
3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)
4. OS Windows XP / VISTA /Windows 7 / Windows 8
5. Direct X version 9.0 or newer
6. Network card 10/100/1000 Mb/s
3.2. Connection with IP camera via the Internet Explorer
You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user
login window will be displayed:
Default user is root and default password is pass.
In the Language box you can change the display language. The default language is English.
For safety reasons, it is recommended to change default user name and password.
It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera
browsers. Running the IP camera in this browsers are very similar.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
16
If your computer has Flash Player ins t a ll ed, the main screen for the camera web interface opens.
From here you can view and configure the ca m e ra .
Caution: If your computer does not have Flash Player ins t a ll ed, you will be prompted t o select if
y o u would like t o use Activ eX or Flash Play er t o connect to the ca m e ra:
 Click Click here to shift playing life video with short delay widget! to play live video with ActiveX
control to reduce latency (recommended): Uses an ActiveX plug-in to connect to the camera. To
install the plug-in, click on the video area, and select Install this Add-on for all users on this
computer, and follow the prompts.
 Click Please download the latest version of Flash Player to play live video: Opens a link to
download Flash Player from Adobe’s website. After completing the installation, restart your
browser and reconnect to the camera.
Caution: In Windows Vista/7/8 the ActiveX applet may be blocked by Windows Defender or User
account control. In such case you should allow to run this applet, or simply disable these
functions.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
17
4. WWW INTERFACE - WORKING WITH IP CAMERA
4.1. Displaying live pictures
1. Camera settings
Live Video - Live video preview
Playback - Play records from SD cards
Device Info - Device information
Stream Configuration - Video and audio settings for each stream
Device Configuration - Device configuration (e.g. Local Network, Date&Time)
External Device - External device configuration (function unavailable)
Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)
Local Record - Local Record Configuration
Privacy Masking - Configuration up to 5 privacy masks
Network Service - Network services configuration (e.g. DDNS)
Service Center - Service center configuration (e.g. SMTP)
Privilege Manager - users and groups management
Protocol - Protocols settings (e.g. ONVIF)
Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log
Maintenance - Device Restart and restoring Default Settings
WWW INTERFACE - WORKING WITH IP CAMERA
3.
4.
1. 2.

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
18
2. Video Parameter
Stream - Stream ID (choose one from available streams)
Bite Rate Type - Bit rate type
Bit Rate (kbps) - Bit rate
I Frame Interval - I frame interval
Quality - Quality
USE TIME STAMP - Video buffer (increases delay when enabled, maximum delay is 5s)
NOTICE: USE TIME STAMP function will not be available when using Flash instead of Activex.
3. Camera Control
Function unavailable.
4. Menu bar
Change Password - Change users password
NOTICE: Default password "pass" can be restored only after restoring default settings of the camera)
Sign Out - Log out from camera
5. Video Control
Camera - Default number of the camera is 1.
Video - Turn on/off video
Audio - Turn on/off audio
Interphone - Turn on/off Interphone
NOTICE: Audio and Interphone functions will not be available when using Flash instead of ActiveX
WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
19
5. ELECTRIC CONNECTORS AND ACCESORIES
5.1. Connecting power supply to the camera.
The camera can be supplied by using RJ45 network socket or by power connector. To run NOVUS IP
camera you can connect ethernet cable between camera and network switch with PoE support (IEEE
802.3af). You can also use a power injector with (IEEE 802.3af) PoE standard. Use power supplay with
parameters compatible with camera specification to power camera via power in jack.
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
Caution:
Make sure to follow the correct polarity if connecting the camera to DC power. Polarity is
marked on the power connector.
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
5.2. Connecting audio inputs/outputs.
5.3. SD card installation
Camera supports microSD and microSDHC cards with their capacity up to 32GB. In order to install the
card properly, please follow the instructions below:
 Turn the camera off
 Mount microSD card in the socket , according to the picture:
ELECTRIC CONNECTORS AND ACCESORIES
Color Description
White RCA Audio input—Connect to a self-powered microphone
for listen-in audio.
Red RCA Audio output—Connect to anamplifier or self-powered
speaker for intercom/2-way audio
microSD

NVIP-2DN5002V/IRH-1P User’s manual ver.1.0
(short form)
All rights reserved © AAT Holding S.A.
20
 Turn the camera on
 Format the card using a IP camera.
Click Local Record ->Record Directory. Click Modify. In menu click Format button.
A window will appear click OK to start formating . Wait for the formatting to complete and then
click OK.
6. RESTORING FACTORY DEFAULTS
NOVUS IP cameras allow to restore defaults via:
 Software (web browser level) resetting the camera settings
 Hardware (using reset) restores factory defaults.
6.1. Restoring software factory defaults
Restoring factory software default can restore default settings of the IP camera ,optionally network
settings can be saved.
Logon to the camera and choose MAINTENANCE> DEFAULT SETTINGS.
 Check the Save the IP setting box to preserve IP seting after restore.
 Click Restore button. The camera re-starts then, taking about two minutes to complete.
 Log on approx. using default user name (root) and password (pass)
6.2. Restoring hardware factory defaults in IP cameras
In order to restore factory defaults for the camera please follow the instructions:
 Remove the camera cover screws (2x) and remove the camera cover
 Press and hold the white reset button for 5 seconds then release the button to reset the camera to
factory defaults
 Re-attach the camera cover and replace the camera cover screws (2x)
 Log on after approx. 2 minutes using default IP address (http://192.168.1.200) and default user
name (root) and password (pass)
ELECTRIC CONNECTORS AND ACCESORIES
Reset button