NRS EASYLIFT N43541 User manual

1
USER INSTRUCTIONS
EASYLIFT OVER BED/CHAIR TABLE
N43541 Easylift Over Bed Table Beech Top – Standard Base
N43553 Easylift Over Bed Table Beech Top – Standard Base – Low
N43565 Easylift Over Bed/Chair Table – Beech Top – Curved Base
N43577 Easylift Over Bed/Chair Table – Standard Top – Curved Base
N43589 Easylift Over Bed/Chair Table – Tilt Top – Curved Base
N85195 Easylift Over Bed/Chair Table – Beech Tilt Top – Curved Base
General Safety Warning
Please make sure that you read and follow
these instructions carefully. Keep these
instructions in a safe place for future reference.
1. INTENDED USE
The Easylift Over Bed Table Range provides
users with a rm, at surface that is suitable for
eating, writing, reading, etc. The single column
construction and adjustable height makes them
suitable for use with most types of beds and chairs.
N43565, N43577, N43589 & N85195 are also
suitable for use with wheelchairs.
2. SAFETY
Warnings:
• Do not exceed the safe working load of 25 kg
(55 lbs) evenly distributed.
• Do not lean or sit on the table.
• Correctly position and adjust the table for safe
and comfortable use.
• Do not place hot utensils, crockery etc. directly
on the table surface. It has a maximum heat
resistance of 65°C (149°F).
• Take care when moving the table over rough or
uneven surfaces. Lift the table over large ridges
and wide gaps.
• Take care with tilting table tops not to trap
ngers between xed and moving parts.
Figure 1
N43553
N85195
N43589
N43541
N43565 N43577

2
3. UNPACKING
Remove the packaging and check all parts
carefully. Contact your supplier immediately if
parts are missing or damaged and do not try and
assemble. This product includes all tools needed
for assembly.
3.1 Contents:
1
3
2
Figure 2
1. Table Top Assembly (Fixed or Split Top)
2. Lift Column Assembly
3. Base Assembly (Castors tted)
• M8 x 50 mm Bolts x 3
• M8 x 15 mm Cap Screws x 4
• M8 Washers x 7
• Split Washer x 3
• Spanner
• Hexagon Tool
Warning: Take care when handling the
Spring-Loaded Lift Column Assembly.
The column contains a compression spring
that will open rapidly, in the direction shown
(see Figure 3), if compressed during
assembly. Handle with care.
Once assembled the weight of the Table Top
ensures that the ‘rapid expansion’ does not occur
during use.
Figure 3
4. ASSEMBLY
4.1 To attach the spring-loaded column:
• Remove the protective plastic cap from the nut
and bolt at the end of the column. See Figure 4.
Figure 4
• Put the Base Assembly on its side and locate
the spring column in position. See Figure 5.
Figure 5
• Secure using the M8 x 50 Bolts and the Split
Washers, see Figure 5.

3
4.2 To attach the Table Top:
Figure 6
• Carefully put the Table Top upside down on the
oor. See Figure 6.
Warning: Take care when doing this with
N43589 & N85195 to not allow the hinged
section to swing away from the frame. This
could cause injury and damage the tilt
mechanism.
• Locate the column and base assembly in
position, see Figure 6.
• Secure using the M8 x 15 Cap Screws and M8
Washers.
• Allow the table to extend to the maximum height
position before returning to its castors.
5. ADJUSTMENTS
5.1 Height
To lower the Table Top:
• Lift the lever (A) on the underside of the table
near the spring loaded column, see Figure 7.
• Push down on the Table Top to lower its height.
• Release lever to lock in position.
To raise the Table Top:
• Pull the Table Top upwards. Hold the base down
with your foot when lifting the top.
Figure 7
5.2 Tilt (Models N43589 & N85195 Only)
The tilt angle section of the Table Top will adjust to
angles of 24°, 31°, 37°, 42° and 47°.
Take care not to trap ngers between the xed
and moving parts of the table when using the tilt
mechanism.
To increase the tilt angle:
• Hold the edge of the table (B), see Figure 8.
• Lift the table top until the ratchet (C) engages at
the position you need.
To reduce the tilt angle:
• Hold the edge of the table (B), see Figure 8.
• Lift the table top as far as it will go to release the
ratchet.
• Lower the Table Top back to the at, horizontal
position.
Figure 8
C
B

4
6. MAINTENANCE
Check the castors are securely tted and free to
rotate. Periodically, remove build-up of dirt and
debris.
Check the height adjustment mechanism functions
smoothly and that the table locks securely in
position over the full range of height.
Check the tilt adjustment operates smoothly and
locks securely in position.
Inspect product regularly for signs of wear. Report
any suspected faults or damage immediately to the
supplier and do not use the product.
7. CLEANING INSTRUCTIONS
Clean regularly, using a general purpose, neutral
detergent and warm water.
Please check the suitability of the cleaning products
before use.
To disinfect, wipe with a dilute bleach solution, and
rinse thoroughly with fresh water.
Allow product to fully dry before use/storage.
DO NOT use abrasive cleaners or cloths as
these could permanently damage the surface and
invalidate any warranty.
DO NOT use solvents or phenol based uids to
clean the product.
DO NOT use hot water. The table top has a
maximum heat resistant temperature of 65°C
(149°F).
8. PRODUCT DISPOSAL
Thoroughly clean and sterilise this product before
disposal.
This product is manufactured from metal and
plastic and can be disposed of through Local
Authority Household Waste and Recycling Centres
or through Local Trade Waste Collectors.
9. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period
of 12 months, from the date of purchase, against
faulty materials and workmanship.
This guarantee does not cover; fair wear & tear,
abuse, misuse, interference or tampering with any
part of the product.
Any guarantee issued by NRS Healthcare does not
a󰀨ect your statutory rights.
If you have any problems with our products, please
contact us at the address below.
If you have experienced an injury, contact us but
feel free to contact the Medical and Healthcare
products Regulatory Agency at:
[email protected].uk
N43541-UI-6 02-02-2023
NRS HEALTHCARE Sherwood House, Cartwright Way, Forest Business Park
Bardon Hill, Coalville, Leicestershire, LE67 1UB, UK.
Tel: Customer Services: 0345 121 8111 Email: [e-mail]
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk
10. GLOSSARY
Warning Important Note