nvent Schroff 20836-820 User manual

VME64x System Subrack 8 U
User’s Manual
Product No.:
20836-820
Revision: R1.1, November 14, 2008
Doc-No: 63972-158

Impressum:
Schroff GmbH
D-75334 Straubenhardt, Germany
The details in this manual have been carefully compiled and
checked - supported by certified Quality Management System
to EN ISO 9001/2000
The company cannot accept any liability for errors or misprints.
The company reserves the right to amendments of technical
specifications due to further development and improvement of
products.
Copyright © 2007
All rights and technical modifications reserved.
Rev. Date updated Change
R1.0 November 19, 2007 Initial release
R1.1 November 14, 2008 Part no. FCM added

VME64x System Subrack 8 U
20836-820
www.schroff.biz I R1.1, November 14, 2008
Table of Contents
1 Safety................................................................................................................. 1
1.1 Intended Application............................................................................................ 1
1.2 Safety Instructions............................................................................................... 2
1.3 Safety Symbols used in this document................................................................ 2
1.4 General Safety Precautions................................................................................. 2
1.5 References and Architecture Specifications........................................................ 3
2 Product Definition............................................................................................. 4
2.1 Mechanical Overview........................................................................................... 5
2.2 Subrack................................................................................................................ 6
2.3 VME64x Backplane ............................................................................................. 6
2.4 Power Supply....................................................................................................... 7
2.4.1 Grounding.............................................................................................. 7
2.5 Thermals............................................................................................................ 10
2.6 Fan Control Module (FCM)................................................................................ 11
2.7 Chassis Monitoring Module (CMM) -optional- ................................................... 12
2.8 Display Module.................................................................................................. 13
3 Installation....................................................................................................... 14
3.1 Unpacking.......................................................................................................... 14
3.1.1 Ensuring Proper Airflow....................................................................... 14
3.2 Rack-Mounting................................................................................................... 15
3.3 Initial Operation.................................................................................................. 16
4 Service............................................................................................................. 17
4.1 Technical support and Return for Service Assistance....................................... 17
4.2 Declaration of Conformity.................................................................................. 17
4.3 Scope of delivery............................................................................................... 18
4.4 Accessories ....................................................................................................... 18
4.5 Spare Parts........................................................................................................ 18
5 Technical Data ................................................................................................ 19

VME64x System Subrack 8 U
20836-820
www.schroff.biz II R1.1, November 14, 2008

VME64x System Subrack 8 U Safety
20836-820
www.schroff.biz 1 R1.1, November 14, 2008
1 Safety
1.1 Intended Application
The VME system subrack, described in this manual, is intended as a platform
fora microcomputersystem basedon theVME bussystem (VME(VITA 1-1994)
and VME64x (VITA 1.1-1997)).
The VME64x system subracks are designed for protection class IP 20 and can
be used only in the resp. environments.
For higher protection requirements, a.e. IP 54/55 you must install the system
subrack in a protective case.
VME64x system subracksare not end-products,so there is novalid approval for
this unit. In order to enable stand-alone functionality, additional elements are
required. An operational system is achieved only by way of appropriate VME or
VME64x boards.
The completion and final testing of the units have been carried out, or at least
supervised, by qualified technicians. These instructions are directed exclusively
to these qualified technicians i.e.engineers, trained and qualified electricians
etc.
Make sure that:
• the assembled unit complies with the safety regulations currently applicable
in the country it is going to be used.
• the overall unit complies with all other regulations and specifications at the
place and country of use, e.g. interference limits, approval by the telecom-
munications authorities.

VME64x System Subrack 8 U Safety
20836-820
www.schroff.biz 2 R1.1, November 14, 2008
1.2 Safety Instructions
The intended audience of this User’s Manual is system integrators and
hardware/software engineers.
1.3 Safety Symbols used in this document
1.4 General Safety Precautions
• Service personnel must know the necessary electrical safety, wiring and
connection practices for installing this equipment in a telecommunication
environment.
• Install this equipment only in compliance with local and national electrical
codes.
Hazardous voltage!
This is the electrical hazard symbol. It indicates that there are dangerous
voltages inside the Shelf.
Caution!
This is the user caution symbol. It indicates a condition where damage of the
equipment or injury of the service personnel could occur. To reduce the risk of
damage or injury, follow all steps or procedures as instructed.
Danger of electrostatic discharge!
TheShelfcontainsstaticsensitivedevices.Topreventstaticdamageyoumust
wear an ESD wrist strap.
Warning!
Voltages over 60 VDC can be present in this equipment. This equipment is
intended to be accessed, to be installed and maintained by qualified and
trained service personnel only.
This equipment is designed in accordance with protection class 1!
It must therefore be operated only with protective GND/earth connection!

VME64x System Subrack 8 U Safety
20836-820
www.schroff.biz 3 R1.1, November 14, 2008
1.5 References and Architecture Specifications
• User Manual VME64x Backplanes
Order no.: 73972-103
• Short Form User Manual VME64x Backplanes
Order no.: 73972-074
• User Manual Fan Control Module (FCM)
Order no.: 73972-083
• User Manual Chassis Monitoring Module (CMM)
Order no.: 73972-084
For more information see the catalogue „Electronic Packaging“ and at
www.schroff.biz

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 4 R1.1, November 14, 2008
2 Product Definition
The Schroff VME64x subrack system consists of:
• A shielded 19“ subrack with front assembly area for
6 U front boards according to VME64x Standard (VITA 1.1-1997)
• Rear assembly area for 6 U, 4 HP Rear Transition Modules
• A VME64x (VITA 1.1-1997) Backplane with P0 connectors
• An open frame power supply with wide range input
• Speed controlled fans for cooling the boards
• Fan Control Module (FCM) for fan monitoring/controlling
• Display module
• Mains/line switch
• Chassis Monitoring Module (CMM) -as an option-

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 5 R1.1, November 14, 2008
2.1 Mechanical Overview
Figure 1: Mechanical Overview
10006841
1 VME64x Backplane 6 Fan Tray
2 Front card cage 7 Rear card cage
3 Air filter 8 Power Supply
4 Fan Control Module (FCM) 9 Mains/line switch
5 Display module
FAN
-12V
+12V
+5VTEMP
3.3V
7
8
9
6
1
2
3
4
5

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 6 R1.1, November 14, 2008
2.2 Subrack
The 8 U / 19“ system based on the Schroff europacPro System with EMC
shielding. The subrack is equipped with a front card cage for up to 21 VME64x
Boards (6 U, 4 HP, 160 mm deep) and a rear card cage for up to 21 Rear I/O
Boards (6 U, 4 HP, 80 mm deep).
The lower guide rails are fitted with ESD clips.
2.3 VME64x Backplane
The 6 U 21 slot Backplane with P0 connectors is compliant to:
• VITA 1.1-1997
• VITA 38 Systemmanagement for VME
For more information see the Backplane’s User Manual, Order No.: 73972-074,
in the catalogue and at www.schroff.biz
Variations
The Schroff assembly service can customize your subrack system with:
• Different Backplane configurations
• Drive mounting cassettes
• Special power supplies
• A Chassis Monitoring Module (CMM)
More information in the catalogue or at www.schroff.biz
1 Slot = 4 HP = 20,32 mm

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 7 R1.1, November 14, 2008
2.4 Power Supply
The subrack system has a open frame AC power supply with wide range input.
The power supply is assembled at the rear bottom side.
The power input is provided by a AC mains/line module with IEC 320-C14
connector, integrated mains/line fuses and line filter.
A mains/line switch is located at the lower front side.
The maximum fuse values is 8 A.
2.4.1 Grounding
There is a M6 threaded stut located at the back side. This connector is only for
equipotential bonding. Grounding is achieved through the protective earth
conductor of the power cable!
Hazardous voltage!
Parts of the power supply may be exposed with hazardous voltage. Always
remove mains/line connector before carry out any assembly work.
Caution!
Your system has not been provided with a AC power cable. Purchase a
AC power cable that is approved for use in your country. The AC power cable
must be rated for the product and for the voltage and current marked on the
product's electrical ratings label. The voltage and current rating of the cable
should be greater than the ratings marked on the product.
Warning!
The fuse value has been determined in factory for the maximum power
delivered by the power supply. The fuse value must be changed to the actual
current of the complete equipped system.
Caution!
The unit is designed inaccordance with protection class 1! It must therefore be
operated with protective earth/GND connection. Use only a three conductor
AC power cable with a protective earth conductor that meets the IEC safety
standards!

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 8 R1.1, November 14, 2008
Figure 2: Power Supply
Table 1: Data AC Power Supply
e
10006814
Input voltage nominal 100 - 240 VAC
Mains Frequency 50 / 60 / 400 Hz
Output (max.) 642 W (600 W if U < 200 VAC)
Output voltages 3.3
5.0
12.0
-12.0
V
V
V
V
-
-
-
-
60
60
10
4
A
A
A
A
Ripple < 1 %
Dynamic response < 2 % or 100 mV with 25 % load
step
Recovery time to within 1% < 300 µsec
Overvoltage protection for all voltages
110 – 120 % U > 5 V or
122 – 134 % U < 5 V
Overcurrent protection 105 – 120 % of rated output current
Hold-up time >= 20 ms

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 9 R1.1, November 14, 2008
Figure 3: Block Diagram
10006816

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 10 R1.1, November 14, 2008
2.5 Thermals
The front boards are cooled by forced air convection through 3 speed controlled
24 VDC axial fans (each fan 270 m³/h (160 cfm)).
The fans are assembled on a front-accessable Fan Tray below the card cage.
The fan speed is controlled by the Fan Control Module (FCM) depending on the
exhaust temperature. The average temperature increase at full load is 8 K.
Figure 4: Air Flow
Caution!
To maintain proper airflow, all open slots must be covered with filler panels.
The filler panel should include an airflow baffle that extends to backplane.
10006842

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 11 R1.1, November 14, 2008
2.6 Fan Control Module (FCM)
The Fan Control Module (FCM):
• Monitors and controls up to four fans
• Monitors the signals from up to four temperature sensors
• Controls the Display Module
• Speed up the fans in case of a failure of one fan
• Is able to communicate with the optional Chassis Monitoring Module (CMM)
Up to four NTC temperaturesensors can be connected to the FCM.The highest
temperature level is the reference for the fan speed. If one ore more sensors
exceed 60° C the output for the temperature fail LED and a digital output are
activated. Since the fan speed is temperature controlled by the FCM, the fans
rotate with the lowest speed possible. Lower speeds reduce acoustic noise and
increase the longevity of the fans.
The FCM also controls a Display Module. 4 green LEDs signal the 4 VME64x
voltages, two red LEDs signal over-temperature and fan fail events.
Figure 5: Diagram fan speed/temperature
8
Formore informationsee theFCM’s UserManual, OrderNo.: 73972-083and at
www.schroff.biz
10006807
60
100
Fan Speed
(%)
Over-Temp.

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 12 R1.1, November 14, 2008
2.7 Chassis Monitoring Module (CMM) -optional-
The Chassis Monitoring Module (CMM)
• monitors the four VME64x voltages
• can monitor two additional voltages with a range of ±24 VDC
• can monitor up to seven NTC temperature sensors
• can communicate with the Fan Control Module (FCM)
• provides 16 digital inputs
• provides 10 digital outputs
The CMM is an optional assembly and not included with the subrack by default.
The CMM is a pluggable unit in the 3 U euroboard format with a
3 U/1 HP front panel and can be assembled at the front or rear side.
The CMM allows communicationand remote monitoring via RS-232 or Ethernet
interface. The front panel provides a RJ45 connector (Ethernet) an a D-Sub9
connector (RS-232).
A user interface via HTML page is available.
The CMM can monitor the 4 VME64x voltages and two additional voltages (up
to ±24 VDC). The error status can be displayed by LEDs, through the RS-232
serial interface or via ethernet as a HTML page.
Up to 7 NTC temperature sensors can be connected to the CMM.Two alarm
thresholds between 20° C and 70° C can be set.
The CMM provides 16 digital inputs and 10 digital outputs for custom specific
applications. Four digital outputs are open collector outputs, isolated by opto-
couplers, six digital outputs are TTL-compatible non-isolated.
The CMM is connected to the FCM. The temperature values and the fan speeds
are transferred to the CMM.
For more information see the CMM’s User Manual, Order No.: 73972-084 and
at www.schroff.biz

VME64x System Subrack 8 U Product Definition
20836-820
www.schroff.biz 13 R1.1, November 14, 2008
2.8 Display Module
Figure 6: Display Module
The Display Module is located at the upper front side of the subrack. 4 green
LEDs signal the 4 VME64x voltages, two red LEDs signal over-temperature and
fan fail events.
The Display Module is controlled by the FCM.
When a CMM is present, the Display Module is controlled by the CMM.

VME64x System Subrack 8 U Installation
20836-820
www.schroff.biz 14 R1.1, November 14, 2008
3 Installation
3.1 Unpacking
Consider the following when unpacking and storing the system:
• Leave the system packed until it is needed for immediate installation.
• After unpacking the system, save and store the packaging material in case
the system must be returned.
If the packaging is damaged and possible system damage is present, report to
the shipper and analyze the damage.
3.1.1 Ensuring Proper Airflow
• Install the system in an open rack whenever possible. If installation in an
enclosed rack is unavoidable, ensure that the rack has adequate ventilation.
• Maintain ambient airflow to ensure normal operation. If the airflow is blocked
or restricted, or if the intake air is too warm, an over temperature condition
can occur.
• Ensure that cables from other equipment do not obstruct the airflow through
the systems.
• Use filler panels to cover all empty chassis slots. The filler panel prevents
fan air from escaping out of the front of an open slot.
Caution!
When opening the shipping carton, use caution to avoid damaging the system.
Caution!
To maintain proper airflow, all open slots must be covered with filler panels.
The filler panel should include an airflow baffle that extends to backplane.

VME64x System Subrack 8 U Installation
20836-820
www.schroff.biz 15 R1.1, November 14, 2008
3.2 Rack-Mounting
This subrack system can be installed in 19“ equipment racks. The rack must be
accessible from the front and rear for equipment installation.
Mounting brackets and a rack mount kit come with the system. Allow sufficient
clearance around the rack for system maintenance.
Mounting Instructions:
• Ensure that the rack is constructed to support the weight and dimensions of
the Shelf.
• Install any stabilizers that came with your equipment rack before mounting
or servicing the system in the rack.
• Load the rack from the bottom to the top, with the heaviest system at the
bottom, avoid uneven mechanical loading of the rack.
• We recommend to use also chassis support brackets.
Warning!
Do NOT move the a full equipped system by yourself. Due to the weight at
least two persons are needed to accomplish this task
Warning!
Do NOT stack the system on top of any other equipment. If the system falls, it
can cause severe bodily injury and damage the equipment.

VME64x System Subrack 8 U Installation
20836-820
www.schroff.biz 16 R1.1, November 14, 2008
3.3 Initial Operation
Before starting the system with VME boards the following tests have to be done:
• Ensure that the unit does not get damaged during tranport.
• Check the Protective Earth (PE) resistance, should be < 0,1 Ohm.
• Switch on the system and check all VME voltages on the Backplane
connectors before you plug in the VME boards.
Note: The +12 V output requires 10% minimum load, i.e. a resistor
12 Ohm / 12 W.
• Plug in the VME boards.
• Cover all open Slots with filler panels.
• Tighten the rear panel mounting screws.
• Power-on the system and determine the actual current consumtion.
• Replace the mains fuses suitable to the actual current.
Figure 7: Mains Fuses
Warning!
Voltages over 60 VDC can be present in this equipment. This equipment is
intended to be accessed, to be installed and maintained by qualified and
trained service personnel only.
This eqipment is designed in accordance with protection class 1!
It must therefore be operated only with protective GND/earth connection!
The fuse value has been determined in factory for the maximum power
delivered by the power supply. The fuse value must be adjusted to the actual
current consumtion of the completed system.
Maximum value is 8 A slow blow.
10006815
1 Fuse 2 Power Socket